Intel® Cyclone® 10 GX Transceiver PHY User Guide

Download PDF
ID 683054
Date 4/14/2023
Public
Document Table of Contents
Document Table of Contents x
1. Intel® Cyclone® 10 GX Transceiver PHY Overview 2. Implementing Protocols in Intel® Cyclone® 10 GX Transceivers 3. PLLs and Clock Networks 4. Resetting Transceiver Channels 5. Cyclone® 10 GX Transceiver PHY Architecture 6. Reconfiguration Interface and Dynamic Reconfiguration 7. Calibration 8. Analog Parameter Settings
1. Intel® Cyclone® 10 GX Transceiver PHY Overview x
1.1. Device Transceiver Layout 1.2. Transceiver PHY Architecture Overview 1.3. Calibration 1.4. Intel® Cyclone® 10 GX Transceiver PHY Overview Revision History
1.1. Device Transceiver Layout x
1.1.1. Intel® Cyclone® 10 GX Device Transceiver Layout 1.1.2. Intel® Cyclone® 10 GX Device Package Details
1.2. Transceiver PHY Architecture Overview x
1.2.1. Transceiver Bank Architecture 1.2.2. PHY Layer Transceiver Components 1.2.3. Transceiver Phase-Locked Loops 1.2.4. Clock Generation Block (CGB)
1.2.2. PHY Layer Transceiver Components x
1.2.2.1. The Transceiver Channel
1.2.3. Transceiver Phase-Locked Loops x
1.2.3.1. Advanced Transmit (ATX) PLL 1.2.3.2. Fractional PLL (fPLL) 1.2.3.3. Channel PLL (CMU/CDR PLL)
2. Implementing Protocols in Intel® Cyclone® 10 GX Transceivers x
2.1. Transceiver Design IP Blocks 2.2. Transceiver Design Flow 2.3. Cyclone® 10 GX Transceiver Protocols and PHY IP Support 2.4. Using the Cyclone® 10 GX Transceiver Native PHY IP Core 2.5. Interlaken 2.6. Ethernet 2.7. PCI Express (PIPE) 2.8. CPRI 2.9. Other Protocols 2.10. Simulating the Transceiver Native PHY IP Core 2.11. Implementing Protocols in Intel® Cyclone® 10 GX Transceivers Revision History
2.2. Transceiver Design Flow x
2.2.1. Select and Instantiate the PHY IP Core 2.2.2. Configure the PHY IP Core 2.2.3. Generate the PHY IP Core 2.2.4. Select the PLL IP Core 2.2.5. Configure the PLL IP Core 2.2.6. Generate the PLL IP Core 2.2.7. Reset Controller 2.2.8. Create Reconfiguration Logic 2.2.9. Connect the PHY IP to the PLL IP Core and Reset Controller 2.2.10. Connect Datapath 2.2.11. Make Analog Parameter Settings 2.2.12. Compile the Design 2.2.13. Verify Design Functionality
2.4. Using the Cyclone® 10 GX Transceiver Native PHY IP Core x
2.4.1. Presets 2.4.2. General and Datapath Parameters 2.4.3. PMA Parameters 2.4.4. Enhanced PCS Parameters 2.4.5. Standard PCS Parameters 2.4.6. PCS Direct 2.4.7. Dynamic Reconfiguration Parameters 2.4.8. PMA Ports 2.4.9. Enhanced PCS Ports 2.4.10. Standard PCS Ports 2.4.11. IP Core File Locations 2.4.12. Unused Transceiver Channels
2.4.9. Enhanced PCS Ports x
2.4.9.1. Enhanced PCS TX and RX Control Ports
2.5. Interlaken x
2.5.1. Metaframe Format and Framing Layer Control Word 2.5.2. Interlaken Configuration Clocking and Bonding 2.5.3. How to Implement Interlaken in Cyclone® 10 GX Transceivers 2.5.4. Native PHY IP Parameter Settings for Interlaken
2.5.2. Interlaken Configuration Clocking and Bonding x
2.5.2.1. xN Clock Bonding Scenario 2.5.2.2. TX Multi-Lane Bonding and RX Multi-Lane Deskew Alignment State Machine
2.5.2.2. TX Multi-Lane Bonding and RX Multi-Lane Deskew Alignment State Machine x
2.5.2.2.1. TX FIFO Soft Bonding 2.5.2.2.2. RX Multi-lane FIFO Deskew State Machine
2.6. Ethernet x
2.6.1. Gigabit Ethernet (GbE) and GbE with IEEE 1588v2 2.6.2. 10GBASE-R and 10GBASE-R with IEEE 1588v2 Variants 2.6.3. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core 2.6.4. Acronyms
2.6.1. Gigabit Ethernet (GbE) and GbE with IEEE 1588v2 x
2.6.1.1. 8B/10B Encoding for GbE, GbE with IEEE 1588v2 2.6.1.2. Word Alignment for GbE, GbE with IEEE 1588v2 2.6.1.3. 8B/10B Decoding for GbE, GbE with IEEE 1588v2 2.6.1.4. Rate Match FIFO for GbE 2.6.1.5. How to Implement GbE, GbE with IEEE 1588v2 in Intel® Cyclone® 10 GX Transceivers 2.6.1.6. Native PHY IP Parameter Settings for GbE and GbE with IEEE 1588v2
2.6.1.1. 8B/10B Encoding for GbE, GbE with IEEE 1588v2 x
2.6.1.1.1. Reset Condition for 8B/10B Encoder in GbE, GbE with IEEE 1588v2
2.6.2. 10GBASE-R and 10GBASE-R with IEEE 1588v2 Variants x
2.6.2.1. The XGMII Clocking Scheme in 10GBASE-R 2.6.2.2. How to Implement 10GBASE-R and 10GBASE-R with IEEE 1588v2 in Intel® Cyclone® 10 GX Transceivers 2.6.2.3. Native PHY IP Parameter Settings for 10GBASE-R and 10GBASE-R with IEEE 1588v2 2.6.2.4. Native PHY IP Ports for 10GBASE-R and 10GBASE-R with IEEE 1588v2 Transceiver Configurations
2.6.2.1. The XGMII Clocking Scheme in 10GBASE-R x
2.6.2.1.1. TX FIFO and RX FIFO
2.6.3. 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core x
2.6.3.1. About the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core 2.6.3.2. Using the IP Core 2.6.3.3. Functional Description 2.6.3.4. Configuration Registers 2.6.3.5. Interface Signals
2.6.3.1. About the 1G/2.5G/5G/10G Multi-rate Ethernet PHY Intel® FPGA IP Core x
2.6.3.1.1. Features 2.6.3.1.2. Release Information 2.6.3.1.3. Device Family Support 2.6.3.1.4. Resource Utilization
2.6.3.2. Using the IP Core x
2.6.3.2.1. Parameter Settings
2.6.3.3. Functional Description x
2.6.3.3.1. Clocking and Reset Sequence 2.6.3.3.2. Timing Constraints 2.6.3.3.3. Switching Operation Speed
2.6.3.5. Interface Signals x
2.6.3.5.1. Clock and Reset Signals 2.6.3.5.2. Operating Mode and Speed Signals 2.6.3.5.3. XGMII Signals 2.6.3.5.4. Status Signals 2.6.3.5.5. Serial Interface Signals 2.6.3.5.6. Transceiver Status and Reconfiguration Signals 2.6.3.5.7. Avalon® Memory-Mapped Interface Signals
2.7. PCI Express (PIPE) x
2.7.1. Transceiver Channel Datapath for PIPE 2.7.2. Supported PIPE Features 2.7.3. How to Connect TX PLLs for PIPE Gen1 and Gen2 Modes 2.7.4. How to Implement PCI Express (PIPE) in Cyclone® 10 GX Transceivers 2.7.5. Native PHY IP Parameter Settings for PIPE 2.7.6. fPLL IP Parameter Core Settings for PIPE 2.7.7. ATX PLL IP Parameter Core Settings for PIPE 2.7.8. Native PHY IP Ports for PIPE 2.7.9. fPLL Ports for PIPE 2.7.10. ATX PLL Ports for PIPE 2.7.11. How to Place Channels for PIPE Configurations
2.7.2. Supported PIPE Features x
2.7.2.1. Gen1/Gen2 Features
2.7.2.1. Gen1/Gen2 Features x
2.7.2.1.1. Dynamic Switching Between Gen1 (2.5 Gbps) and Gen2 (5 Gbps) 2.7.2.1.2. Transmitter Electrical Idle Generation 2.7.2.1.3. Power State Management 2.7.2.1.4. 8B/10B Encoder Usage for Compliance Pattern Transmission Support 2.7.2.1.5. Receiver Status 2.7.2.1.6. Receiver Detection 2.7.2.1.7. Gen1 and Gen2 Clock Compensation 2.7.2.1.8. PCIe Reverse Parallel Loopback
2.7.11. How to Place Channels for PIPE Configurations x
2.7.11.1. Master Channel in Bonded Configurations
2.8. CPRI x
2.8.1. Transceiver Channel Datapath and Clocking for CPRI 2.8.2. Supported Features for CPRI 2.8.3. Word Aligner in Manual Mode for CPRI 2.8.4. How to Implement CPRI in Cyclone® 10 GX Transceivers 2.8.5. Native PHY IP Parameter Settings for CPRI
2.8.1. Transceiver Channel Datapath and Clocking for CPRI x
2.8.1.1. TX PLL Selection for CPRI 2.8.1.2. Auto-Negotiation
2.8.2. Supported Features for CPRI x
2.8.2.1. Word Aligner in Deterministic Latency Mode for CPRI
2.8.2.1. Word Aligner in Deterministic Latency Mode for CPRI x
2.8.2.1.1. Transmitter and Receiver Latency
2.9. Other Protocols x
2.9.1. Using the 'Basic (Enhanced PCS)' Configuration 2.9.2. Using the Basic/Custom, Basic/Custom with Rate Match Configurations of Standard PCS 2.9.3. How to Implement PCS Direct Transceiver Configuration Rule
2.9.1. Using the 'Basic (Enhanced PCS)' Configuration x
2.9.1.1. How to Implement the Basic (Enhanced PCS) Transceiver Configuration Rules in Cyclone® 10 GX Transceivers 2.9.1.2. Native PHY IP Parameter Settings for Basic (Enhanced PCS) 2.9.1.3. How to Enable Low Latency in Basic Enhanced PCS 2.9.1.4. Enhanced PCS FIFO Operation 2.9.1.5. TX Data Bitslip 2.9.1.6. TX Data Polarity Inversion 2.9.1.7. RX Data Bitslip 2.9.1.8. RX Data Polarity Inversion
2.9.2. Using the Basic/Custom, Basic/Custom with Rate Match Configurations of Standard PCS x
2.9.2.1. Word Aligner Manual Mode 2.9.2.2. Word Aligner Synchronous State Machine Mode 2.9.2.3. RX Bit Slip 2.9.2.4. RX Polarity Inversion 2.9.2.5. RX Bit Reversal 2.9.2.6. RX Byte Reversal 2.9.2.7. Rate Match FIFO in Basic (Single Width) Mode 2.9.2.8. Rate Match FIFO Basic (Double Width) Mode 2.9.2.9. 8B/10B Encoder and Decoder 2.9.2.10. 8B/10B TX Disparity Control 2.9.2.11. How to Enable Low Latency in Basic 2.9.2.12. TX Bit Slip 2.9.2.13. TX Polarity Inversion 2.9.2.14. TX Bit Reversal 2.9.2.15. TX Byte Reversal 2.9.2.16. How to Implement the Basic, Basic with Rate Match Transceiver Configuration Rules in Cyclone® 10 GX Transceivers 2.9.2.17. Native PHY IP Parameter Settings for Basic, Basic with Rate Match Configurations
2.10. Simulating the Transceiver Native PHY IP Core x
2.10.1. NativeLink Simulation Flow 2.10.2. Scripting IP Simulation 2.10.3. Custom Simulation Flow
2.10.1. NativeLink Simulation Flow x
2.10.1.1. How to Use NativeLink to Specify a ModelSim Simulation 2.10.1.2. How to Use NativeLink to Run a ModelSim RTL Simulation 2.10.1.3. How to Use NativeLink to Specify Third-Party RTL Simulators
2.10.2. Scripting IP Simulation x
2.10.2.1. Generating a Combined Simulator Setup Script
2.10.3. Custom Simulation Flow x
2.10.3.1. How to Use the Simulation Library Compiler 2.10.3.2. Custom Simulation Scripts
3. PLLs and Clock Networks x
3.1. PLLs 3.2. Input Reference Clock Sources 3.3. Transmitter Clock Network 3.4. Clock Generation Block 3.5. FPGA Fabric-Transceiver Interface Clocking 3.6. Transmitter Data Path Interface Clocking 3.7. Receiver Data Path Interface Clocking 3.8. Unused/Idle Clock Line Requirements 3.9. Channel Bonding 3.10. PLL Feedback and Cascading Clock Network 3.11. Using PLLs and Clock Networks 3.12. PLLs and Clock Networks Revision History
3.1. PLLs x
3.1.1. Transmit PLLs Spacing Guidelines when using ATX PLLs and fPLLs 3.1.2. ATX PLL 3.1.3. fPLL 3.1.4. CMU PLL
3.1.2. ATX PLL x
3.1.2.1. Instantiating the ATX PLL IP Core 3.1.2.2. ATX PLL IP Core
3.1.3. fPLL x
3.1.3.1. Instantiating the fPLL IP Core 3.1.3.2. fPLL IP Core
3.1.4. CMU PLL x
3.1.4.1. Instantiating CMU PLL IP Core 3.1.4.2. CMU PLL IP Core
3.2. Input Reference Clock Sources x
3.2.1. Dedicated Reference Clock Pins 3.2.2. Receiver Input Pins 3.2.3. PLL Cascading as an Input Reference Clock Source 3.2.4. Reference Clock Network 3.2.5. Global Clock or Core Clock as an Input Reference Clock
3.3. Transmitter Clock Network x
3.3.1. x1 Clock Lines 3.3.2. x6 Clock Lines 3.3.3. xN Clock Lines
3.9. Channel Bonding x
3.9.1. PMA Bonding 3.9.2. PMA and PCS Bonding 3.9.3. Selecting Channel Bonding Schemes 3.9.4. Skew Calculations
3.9.1. PMA Bonding x
3.9.1.1. x6/xN Bonding 3.9.1.2. PLL Feedback Compensation Bonding
3.11. Using PLLs and Clock Networks x
3.11.1. Non-bonded Configurations 3.11.2. Bonded Configurations 3.11.3. Implementing PLL Cascading 3.11.4. Timing Closure Recommendations
3.11.1. Non-bonded Configurations x
3.11.1.1. Implementing Single Channel x1 Non-Bonded Configuration 3.11.1.2. Implementing Multi-Channel x1 Non-Bonded Configuration 3.11.1.3. Implementing Multi-Channel xN Non-Bonded Configuration
3.11.2. Bonded Configurations x
3.11.2.1. Implementing x6/xN Bonding Mode 3.11.2.2. Implementing PLL Feedback Compensation Bonding Mode
4. Resetting Transceiver Channels x
4.1. When Is Reset Required? 4.2. Transceiver PHY Implementation 4.3. How Do I Reset? 4.4. Using the Transceiver PHY Reset Controller 4.5. Using a User-Coded Reset Controller 4.6. Combining Status or PLL Lock Signals 4.7. Timing Constraints for Bonded PCS and PMA Channels 4.8. Resetting Transceiver Channels Revision History
4.3. How Do I Reset? x
4.3.1. Model 1: Default Model 4.3.2. Model 2: Acknowledgment Model 4.3.3. Transceiver Blocks Affected by Reset and Powerdown Signals
4.3.1. Model 1: Default Model x
4.3.1.1. Recommended Reset Sequence 4.3.1.2. Resetting the Transmitter During Device Operation 4.3.1.3. Resetting the Receiver During Device Operation 4.3.1.4. Resetting the Transceiver Channel During Device Operation 4.3.1.5. Dynamic Reconfiguration of Channel Using the Default Model
4.3.1.3. Resetting the Receiver During Device Operation x
4.3.1.3.1. Clock Data Recovery in Auto Lock Mode 4.3.1.3.2. Clock Data Recovery in Manual Lock Mode 4.3.1.3.3. Control Settings for CDR Manual Lock Mode 4.3.1.3.4. Resetting the Transceiver in CDR Manual Lock Mode
4.3.2. Model 2: Acknowledgment Model x
4.3.2.1. Recommended Reset Sequence 4.3.2.2. Resetting the Transmitter During Device Operation 4.3.2.3. Resetting the Receiver During Device Operation 4.3.2.4. Dynamic Reconfiguration of Transmitter Channel Using the Acknowledgment Model 4.3.2.5. Dynamic Reconfiguration of Receiver Channel Using the Acknowledgment Model
4.4. Using the Transceiver PHY Reset Controller x
4.4.1. Parameterizing the Transceiver PHY Reset Controller IP 4.4.2. Transceiver PHY Reset Controller Parameters 4.4.3. Transceiver PHY Reset Controller Interfaces 4.4.4. Transceiver PHY Reset Controller Resource Utilization
4.5. Using a User-Coded Reset Controller x
4.5.1. User-Coded Reset Controller Signals
5. Cyclone® 10 GX Transceiver PHY Architecture x
5.1. Cyclone® 10 GX PMA Architecture 5.2. Cyclone® 10 GX Enhanced PCS Architecture 5.3. Cyclone® 10 GX Standard PCS Architecture 5.4. Intel® Cyclone® 10 GX Transceiver PHY Architecture Revision History
5.1. Cyclone® 10 GX PMA Architecture x
5.1.1. Transmitter 5.1.2. Serializer 5.1.3. Transmitter Buffer 5.1.4. Receiver 5.1.5. Receiver Buffer 5.1.6. Clock Data Recovery (CDR) Unit 5.1.7. Deserializer 5.1.8. Loopback
5.1.3. Transmitter Buffer x
5.1.3.1. High Speed Differential I/O 5.1.3.2. Programmable Output Differential Voltage 5.1.3.3. Programmable Pre-Emphasis 5.1.3.4. Power Distribution Network (PDN) induced Inter-Symbol Interference (ISI) compensation 5.1.3.5. Programmable Transmitter On-Chip Termination (OCT)
5.1.5. Receiver Buffer x
5.1.5.1. Programmable Common Mode Voltage (VCM) 5.1.5.2. Programmable Differential On-Chip Termination (OCT) 5.1.5.3. Signal Detector 5.1.5.4. Continuous Time Linear Equalization (CTLE) 5.1.5.5. Variable Gain Amplifier (VGA) 5.1.5.6. How to Enable CTLE
5.1.5.4. Continuous Time Linear Equalization (CTLE) x
5.1.5.4.1. High Gain Mode
5.1.5.6. How to Enable CTLE x
5.1.5.6.1. Configuration Methods
5.1.6. Clock Data Recovery (CDR) Unit x
5.1.6.1. Lock-to-Reference Mode 5.1.6.2. Lock-to-Data Mode 5.1.6.3. CDR Lock Modes
5.1.6.3. CDR Lock Modes x
5.1.6.3.1. Automatic Lock Mode 5.1.6.3.2. Manual Lock Mode
5.2. Cyclone® 10 GX Enhanced PCS Architecture x
5.2.1. Transmitter Datapath 5.2.2. Receiver Datapath
5.2.1. Transmitter Datapath x
5.2.1.1. Enhanced PCS TX FIFO 5.2.1.2. Interlaken Frame Generator 5.2.1.3. Interlaken CRC-32 Generator 5.2.1.4. 64B/66B Encoder and Transmitter State Machine (TX SM) 5.2.1.5. Pattern Generators 5.2.1.6. Scrambler 5.2.1.7. Interlaken Disparity Generator 5.2.1.8. TX Gearbox, TX Bitslip and Polarity Inversion
5.2.1.1. Enhanced PCS TX FIFO x
5.2.1.1.1. Phase Compensation Mode 5.2.1.1.2. Register Mode 5.2.1.1.3. Interlaken Mode 5.2.1.1.4. Basic Mode
5.2.1.5. Pattern Generators x
5.2.1.5.1. PRBS Pattern Generator (Shared between Enhanced PCS and Standard PCS) 5.2.1.5.2. Pseudo-Random Pattern Generator
5.2.2. Receiver Datapath x
5.2.2.1. RX Gearbox, RX Bitslip, and Polarity Inversion 5.2.2.2. Block Synchronizer 5.2.2.3. Interlaken Disparity Checker 5.2.2.4. Descrambler 5.2.2.5. Interlaken Frame Synchronizer 5.2.2.6. 64B/66B Decoder and Receiver State Machine (RX SM) 5.2.2.7. Pseudo Random Pattern Verifier 5.2.2.8. 10GBASE-R Bit-Error Rate (BER) Checker 5.2.2.9. Interlaken CRC-32 Checker 5.2.2.10. Enhanced PCS RX FIFO
5.2.2.6. 64B/66B Decoder and Receiver State Machine (RX SM) x
5.2.2.6.1. PRBS Checker
5.2.2.10. Enhanced PCS RX FIFO x
5.2.2.10.1. Phase Compensation Mode 5.2.2.10.2. Register Mode 5.2.2.10.3. Interlaken Mode 5.2.2.10.4. 10GBASE-R Mode 5.2.2.10.5. Idle OS Deletion 5.2.2.10.6. Idle Insertion 5.2.2.10.7. Basic Mode
5.3. Cyclone® 10 GX Standard PCS Architecture x
5.3.1. Transmitter Datapath 5.3.2. Receiver Datapath
5.3.1. Transmitter Datapath x
5.3.1.1. TX FIFO (Shared with Enhanced PCS and PCIe Gen2 PCS) 5.3.1.2. Byte Serializer 5.3.1.3. 8B/10B Encoder 5.3.1.4. Polarity Inversion Feature 5.3.1.5. Pseudo-Random Binary Sequence (PRBS) Generator 5.3.1.6. TX Bit Slip
5.3.1.1. TX FIFO (Shared with Enhanced PCS and PCIe Gen2 PCS) x
5.3.1.1.1. TX FIFO Low Latency Mode 5.3.1.1.2. TX FIFO Register Mode 5.3.1.1.3. TX FIFO Fast Register Mode
5.3.1.2. Byte Serializer x
5.3.1.2.1. Bonded Byte Serializer 5.3.1.2.2. Byte Serializer Disabled Mode 5.3.1.2.3. Byte Serializer Serialize x2 Mode 5.3.1.2.4. Byte Serializer Serialize x4 Mode
5.3.1.3. 8B/10B Encoder x
5.3.1.3.1. 8B/10B Encoder Control Code Encoding 5.3.1.3.2. 8B/10B Encoder Reset Condition 5.3.1.3.3. 8B/10B Encoder Idle Character Replacement Feature 5.3.1.3.4. 8B/10B Encoder Current Running Disparity Control Feature 5.3.1.3.5. 8B/10B Encoder Bit Reversal Feature 5.3.1.3.6. 8B/10B Encoder Byte Reversal Feature
5.3.2. Receiver Datapath x
5.3.2.1. Word Aligner 5.3.2.2. RX Polarity Inversion Feature 5.3.2.3. Rate Match FIFO 5.3.2.4. 8B/10B Decoder 5.3.2.5. Pseudo-Random Binary Sequence (PRBS) Checker 5.3.2.6. Byte Deserializer 5.3.2.7. RX FIFO (Shared with Enhanced PCS and PCIe Gen2 PCS)
5.3.2.1. Word Aligner x
5.3.2.1.1. Word Aligner Bit Slip Mode 5.3.2.1.2. Word Aligner Manual Mode 5.3.2.1.3. Word Aligner Synchronous State Machine Mode 5.3.2.1.4. Word Aligner Deterministic Latency Mode 5.3.2.1.5. Word Aligner Pattern Length for Various Word Aligner Modes 5.3.2.1.6. Word Aligner RX Bit Reversal Feature 5.3.2.1.7. Word Aligner RX Byte Reversal Feature
5.3.2.4. 8B/10B Decoder x
5.3.2.4.1. 8B/10B Decoder Control Code Encoding 5.3.2.4.2. 8B/10B Decoder Running Disparity Checker Feature
5.3.2.6. Byte Deserializer x
5.3.2.6.1. Byte Deserializer Disabled Mode 5.3.2.6.2. Byte Deserializer Deserialize x2 Mode 5.3.2.6.3. Byte Deserializer Deserialize x4 Mode 5.3.2.6.4. Bonded Byte Deserializer
5.3.2.7. RX FIFO (Shared with Enhanced PCS and PCIe Gen2 PCS) x
5.3.2.7.1. RX FIFO Low Latency Mode 5.3.2.7.2. RX FIFO Register Mode
6. Reconfiguration Interface and Dynamic Reconfiguration x
6.1. Reconfiguring Channel and PLL Blocks 6.2. Interacting with the Reconfiguration Interface 6.3. Configuration Files 6.4. Multiple Reconfiguration Profiles 6.5. Embedded Reconfiguration Streamer 6.6. Arbitration 6.7. Recommendations for Dynamic Reconfiguration 6.8. Steps to Perform Dynamic Reconfiguration 6.9. Direct Reconfiguration Flow 6.10. Native PHY IP or PLL IP Core Guided Reconfiguration Flow 6.11. Reconfiguration Flow for Special Cases 6.12. Changing PMA Analog Parameters 6.13. Ports and Parameters 6.14. Dynamic Reconfiguration Interface Merging Across Multiple IP Blocks 6.15. Embedded Debug Features 6.16. Using Data Pattern Generators and Checkers 6.17. Timing Closure Recommendations 6.18. Unsupported Features 6.19. Cyclone® 10 GX Transceiver Register Map 6.20. Reconfiguration Interface and Dynamic Reconfiguration Revision History
6.2. Interacting with the Reconfiguration Interface x
6.2.1. Reading from the Reconfiguration Interface 6.2.2. Writing to the Reconfiguration Interface
6.11. Reconfiguration Flow for Special Cases x
6.11.1. Switching Transmitter PLL 6.11.2. Switching Reference Clocks
6.11.2. Switching Reference Clocks x
6.11.2.1. ATX Reference Clock Switching 6.11.2.2. fPLL Reference Clock Switching 6.11.2.3. CDR and CMU Reference Clock Switching
6.12. Changing PMA Analog Parameters x
6.12.1. Changing VOD, Pre-emphasis Using Direct Reconfiguration Flow 6.12.2. Changing CTLE Settings in Manual Mode Using Direct Reconfiguration Flow 6.12.3. Enabling and Disabling Loopback Modes Using Direct Reconfiguration Flow
6.15. Embedded Debug Features x
6.15.1. Native PHY Debug Master Endpoint 6.15.2. Optional Reconfiguration Logic
6.15.2. Optional Reconfiguration Logic x
6.15.2.1. Capability Registers 6.15.2.2. Control and Status Registers 6.15.2.3. PRBS Soft Accumulators
6.16. Using Data Pattern Generators and Checkers x
6.16.1. Using PRBS Data Pattern Generator and Checker 6.16.2. Using Pseudo Random Pattern Mode
6.16.1. Using PRBS Data Pattern Generator and Checker x
6.16.1.1. Enabling the PRBS Data Generator in Non Bonded designs 6.16.1.2. Enabling the PRBS Data Generator in Bonded Designs 6.16.1.3. Enabling the PRBS Data Checker in Non Bonded design 6.16.1.4. Enabling the PRBS Checker in bonded designs 6.16.1.5. Disabling/Enabling PRBS Pattern Inversion
6.16.1.1. Enabling the PRBS Data Generator in Non Bonded designs x
6.16.1.1.1. Examples of Enabling the PRBS9 and PRBS31 Pattern Generators in Non Bonded designs
6.16.1.2. Enabling the PRBS Data Generator in Bonded Designs x
6.16.1.2.1. Examples of Enabling the PRBS9 and PRBS31 Pattern Generators in Bonded Designs
6.16.1.3. Enabling the PRBS Data Checker in Non Bonded design x
6.16.1.3.1. Examples of Enabling the PRBS Data Checker
6.16.2. Using Pseudo Random Pattern Mode x
6.16.2.1. Enabling Pseudo Random Pattern Mode
7. Calibration x
7.1. Reconfiguration Interface and Arbitration with PreSICE Calibration Engine 7.2. Calibration Registers 7.3. Power-up Calibration 7.4. User Recalibration 7.5. Calibration Example 7.6. Calibration Revision History
7.2. Calibration Registers x
7.2.1. Avalon® Memory-Mapped Interface Arbitration Registers 7.2.2. Transceiver Channel Calibration Registers 7.2.3. Fractional PLL Calibration Registers 7.2.4. ATX PLL Calibration Registers 7.2.5. Capability Registers 7.2.6. Rate Switch Flag Register
7.2.5. Capability Registers x
7.2.5.1. Rules to Build Customized Gating Logic to Separate tx_cal_busy and rx_cal_busy signals 7.2.5.2. PMA Capability Registers for Calibration Status
7.4. User Recalibration x
7.4.1. Conditions That Require User Recalibration 7.4.2. User Recalibration Sequence
7.5. Calibration Example x
7.5.1. ATX PLL Recalibration 7.5.2. Fractional PLL Recalibration 7.5.3. CDR/CMU PLL Recalibration 7.5.4. PMA Recalibration
8. Analog Parameter Settings x
8.1. Making Analog Parameter Settings using the Assignment Editor 8.2. Updating Quartus Settings File with the Known Assignment 8.3. Analog Parameter Settings List 8.4. Receiver General Analog Settings 8.5. Receiver Analog Equalization Settings 8.6. Transmitter General Analog Settings 8.7. Transmitter Pre-Emphasis Analog Settings 8.8. Transmitter VOD Settings 8.9. Dedicated Reference Clock Settings 8.10. Unused Transceiver Channels Settings 8.11. Analog Parameter Settings Revision History
8.4. Receiver General Analog Settings x
8.4.1. XCVR_C10_RX_TERM_SEL
8.5. Receiver Analog Equalization Settings x
8.5.1. CTLE Settings 8.5.2. VGA Settings
8.5.1. CTLE Settings x
8.5.1.1. XCVR_C10_RX_ONE_STAGE_ENABLE 8.5.1.2. XCVR_C10_RX_EQ_DC_GAIN_TRIM 8.5.1.3. XCVR_C10_RX_ADP_CTLE_ACGAIN_4S 8.5.1.4. XCVR_C10_RX_ADP_CTLE_EQZ_1S_SEL
8.5.2. VGA Settings x
8.5.2.1. XCVR_C10_RX_ADP_VGA_SEL
8.6. Transmitter General Analog Settings x
8.6.1. XCVR_C10_TX_TERM_SEL 8.6.2. XCVR_C10_TX_COMPENSATION_EN 8.6.3. XCVR_C10_TX_SLEW_RATE_CTRL
8.7. Transmitter Pre-Emphasis Analog Settings x
8.7.1. XCVR_C10_TX_PRE_EMP_SIGN_PRE_TAP_1T 8.7.2. XCVR_C10_TX_PRE_EMP_SIGN_PRE_TAP_2T 8.7.3. XCVR_C10_TX_PRE_EMP_SIGN_1ST_POST_TAP 8.7.4. XCVR_C10_TX_PRE_EMP_SIGN_2ND_POST_TAP 8.7.5. XCVR_C10_TX_PRE_EMP_SWITCHING_CTRL_PRE_TAP_1T 8.7.6. XCVR_C10_TX_PRE_EMP_SWITCHING_CTRL_PRE_TAP_2T 8.7.7. XCVR_C10_TX_PRE_EMP_SWITCHING_CTRL_1ST_POST_TAP 8.7.8. XCVR_C10_TX_PRE_EMP_SWITCHING_CTRL_2ND_POST_TAP
8.8. Transmitter VOD Settings x
8.8.1. XCVR_C10_TX_VOD_OUTPUT_SWING_CTRL
8.9. Dedicated Reference Clock Settings x
8.9.1. XCVR_C10_REFCLK_TERM_TRISTATE 8.9.2. XCVR_C10_TX_XTX_PATH_ANALOG_MODE
1. Intel® Cyclone® 10 GX Transceiver PHY Overview
2. Implementing Protocols in Intel® Cyclone® 10 GX Transceivers
3. PLLs and Clock Networks
4. Resetting Transceiver Channels
5. Cyclone® 10 GX Transceiver PHY Architecture
6. Reconfiguration Interface and Dynamic Reconfiguration
7. Calibration
8. Analog Parameter Settings

3.1.2.2. ATX PLL IP Core

Table 154.  ATX PLL Configuration Options, Parameters, and Settings
Parameter Range Description

Message level for rule violations

Error

Warning

Specifies the messaging level to use for parameter rule violations.

  • Error—Causes all rule violations to prevent IP generation.
  • Warning—Displays all rule violations as warnings and allows IP generation in spite of violations.

Protocol mode

Basic

PCIe* Gen1

PCIe Gen2

SAS TX

Governs the internal setting rules for the VCO.

This parameter is not a preset. You must set all other parameters for your protocol.

Bandwidth

Low

Medium

High

Specifies the VCO bandwidth.

Higher bandwidth reduces PLL lock time, at the expense of decreased jitter rejection.

Number of PLL reference clocks

1 to 5

Specifies the number of input reference clocks for the ATX PLL.

You can use this parameter for data rate reconfiguration.

Selected reference clock source

0 to 4

Specifies the initially selected reference clock input to the ATX PLL.

Primary PLL clock output buffer

 GX clock output buffer

Specifies which PLL output is active initially.

  • If GX is selected, turn ON "Enable PLL GX clock output port".
Enable PLL GX clock output port

On/Off 

Enables the GX output port which feeds x1 clock lines.

You must select this parameter for PLL output frequency less than 8.7 GHz, or if you intend to reconfigure the PLL to a frequency below 8.7 GHz.

Turn ON this port if GX is selected in the "Primary PLL clock output buffer".

Enable PCIe clock output port 

 On/Off

Exposes the pll_pcie_clk port used for PCI Express*.

The port should be connected to the pipe_hclk_input port.

PLL output frequency

Refer to Intel® Arria® 10 Device Datasheet .

Use this parameter to specify the target output frequency for the PLL.

PLL integer reference clock frequency

Refer to the GUI

Selects the input reference clock frequency for the PLL.

Table 155.  ATX PLL—Master Clock Generation Block Parameters and Settings
Parameter Range Description

Include Master Clock Generation Block 28

On/Off

When enabled, includes a master CGB as a part of the ATX PLL IP core. The PLL output drives the Master CGB.

This is used for x6/xN bonded and non-bonded modes.

Clock division factor

 1, 2, 4, 8

Divides the master CGB clock input before generating bonding clocks.

Enable x6/xN non-bonded high-speed clock output port

 On/Off

Enables the master CGB serial clock output port used for x6/xN non-bonded modes.

Enable PCIe clock switch interface

 On/Off

Enables the control signals for the PCIe clock switch circuitry. Used for PCIe clock rate switching.

Number of auxiliary MCGB clock input ports

0, 1

Auxiliary input is used to implement the PCIe Gen3 protocol.

MCGB input clock frequency

Read only

Displays the master CGB's input clock frequency.

MCGB output data rate.

Read only

Displays the master CGB's output data rate.

Enable bonding clock output ports

On/Off

Enables the tx_bonding_clocks output ports of the master CGB used for channel bonding.

This option should be turned ON for bonded designs.

Enable feedback compensation bonding

On/Off

Enables this setting when using feedback compensation bonding. For more details about feedback compensation bonding, refer to the PLL Feedback Compensation Bonding section later in the document.

PMA interface width

8, 10, 16, 20, 32, 40, 64

Specifies PMA-PCS interface width.

Match this value with the PMA interface width selected for the Native PHY IP core. You must select a proper value for generating bonding clocks for the Native PHY IP core.

Table 156.  ATX PLL—Dynamic Reconfiguration
Parameter Range Description

Enable reconfiguration

On/Off

Enables the PLL reconfiguration interface. Enables the simulation models and adds Avalon® compliant ports for reconfiguration.

Enable Native PHY Debug Master Endpoint

On/Off

When you turn on this option, the Transceiver PLL IP core includes an embedded Native PHY Debug Master Endpoint (NPDME) that connects internally to the Avalon® memory-mapped interface slave interface for dynamic reconfiguration. The NPDME can access the reconfiguration space of the transceiver. It can perform certain test and debug functions via JTAG using the System Console. Refer to the Reconfiguration Interface and Dynamic Reconfiguration chapter for more details.

Separate reconfig_waitrequest from the status of AVMM arbitration with PreSICE

On/Off

When enabled, the reconfig_waitrequest does not indicate the status of Avalon® memory-mapped interface arbitration with PreSICE. The Avalon® memory-mapped interface arbitration status is reflected in a soft status register bit. (Only available if "Enable control and status registers feature" is enabled).

Enable capability registers

On/Off

Enables capability registers that provide high-level information about the ATX PLL's configuration.

Set user-defined IP identifier

User-defined

Sets a user-defined numeric identifier that can be read from the user_identifier offset when the capability registers are enabled.

Enable control and status registers

On/Off

Enables soft registers for reading status signals and writing control signals on the PLL interface through the embedded debug logic.

Configuration file prefix

Enter the prefix name for the configuration files to be generated.

Generate SystemVerilog package file 

On/Off

Generates a SystemVerilog package file containing all relevant parameters used by the PLL.

Generate C header file

On/Off

Generates a C header file containing all relevant parameters used by the PLL.

Enable multiple reconfiguration profiles

On/Off

Enables multiple configuration profiles to be stored.

Enable embedded reconfiguration streamer

On/Off

Enables embedded reconfiguration streamer which automates the dynamic reconfiguration process between multiple predefined configuration profiles.

Generate reduced reconfiguration files

On/Off

When enabled, the IP generates reconfiguration report files containing only the setting differences between the multiple reconfiguration profiles

Number of reconfiguration profiles

1 to 8

Specifies the number of reconfiguration profiles

Store current configuration to profile

0 to 7

Specifies which configuration profile to modify (store, load, clear or refresh) when clicking the corresponding action button.

Generate MIF (Memory Initialize File)

On/Off

Generates a MIF file which contains the current configuration.

Use this option for reconfiguration purposes in order to switch between different PLL configurations.

Table 157.  ATX PLL—Generation Options
Parameter Range Description

Generate parameter documentation file

On/Off

Generates a .csv file which contains descriptions of ATX PLL IP core parameters and values.

Table 158.  ATX PLL IP Core Ports
Port Direction Clock Domain Description

pll_powerdown

Input

Asynchronous

Resets the PLL when asserted high. Needs to be connected to a dynamically controlled signal (the Transceiver PHY Reset Controller pll_powerdown output if using this Intel FPGA IP).

pll_refclk0

Input

N/A

Reference clock input port 0.

There are a total of five reference clock input ports. The number of reference clock ports available depends on the Number of PLL reference clocks parameter.

pll_refclk1

Input

N/A

Reference clock input port 1.

pll_refclk2

Input

N/A

Reference clock input port 2.

pll_refclk3

Input

N/A

Reference clock input port 3.

pll_refclk4

Input

N/A

Reference clock input port 4.

tx_serial_clk

Output

N/A

High speed serial clock output port for GX channels. Represents the x1 clock network.

pll_locked

Output

Asynchronous

Active high status signal which indicates if the PLL is locked.

pll_pcie_clk

Output

N/A

Used for PCIe. 29

reconfig_clk0

Input

N/A

Optional Avalon® interface clock. Used for PLL reconfiguration. The reconfiguration ports appear only if the Enable Reconfiguration parameter is selected in the PLL IP Core GUI. When this parameter is not selected, the ports are set to OFF internally.

reconfig_reset0

Input

reconfig_clk0

Used to reset the Avalon® interface. Asynchronous to assertion and synchronous to deassertion.

reconfig_write0

Input

reconfig_clk0

Active high write enable signal.

reconfig_read0

Input

reconfig_clk0

Active high read enable signal.

reconfig_address0[9:0]

Input

reconfig_clk0

10-bit address bus used to specify address to be accessed for both read and write operations.

reconfig_writedata0[31:0]

Input

reconfig_clk0

32-bit data bus. Carries the write data to the specified address.

reconfig_readdata0[31:0]

Output

reconfig_clk0

32-bit data bus. Carries the read data from the specified address.

reconfig_waitrequest0

Output

reconfig_clk0

Indicates when the Avalon® interface signal is busy. When asserted, all inputs must be held constant.

pll_cal_busy

Output

Asynchronous

Status signal which is asserted high when PLL calibration is in progress.

OR this signal with tx_cal_busy port before connecting to the reset controller IP.

mcgb_rst

Input

Asynchronous

Master CGB reset control.

Deassert this reset at the same time as pll_powerdown .

tx_bonding_clocks[5:0]

Output

N/A

Optional 6-bit bus which carries the low speed parallel clock outputs from the master CGB. Each transceiver channel in a bonded group has this 6-bit bus.

Used for channel bonding, and represents the x6/xN clock network.

mcgb_serial_clk

Output

N/A

High speed serial clock output for x6/xN non-bonded configurations.

pcie_sw[1:0]

Input

Asynchronous

2-bit rate switch control input used for PCIe protocol implementation.

pcie_sw_done[1:0]

Output

Asynchronous

2-bit rate switch status output used for PCIe protocol implementation.

ext_lock_detect_clklow 30

Output

N/A

Clklow output for external lock detection. It can be exposed by selecting the Enable clklow and fref port

ext_lock_detect_fref 30

Output

N/A

Fref output for external lock detection. It can be exposed by selecting the Enable clklow and fref port.
Related Information
28 Manually enable the MCGB for bonding applications.
29 Connect this clock to hclk in PCIe applications.
30 The fPLL fref and clklow signals should only be used with the Intel® external soft lock detection logic.
Level Two Title