External Memory Interfaces Intel® Agilex™ FPGA IP User Guide

ID 683216
Date 6/20/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

7.3.3.2. General Guidelines

You should follow the recommended guidelines when performing pin placement for all external memory interface pins targeting Intel® Agilex™ devices, whether you are using the hard memory controller or your own solution.
Note:
  • EMIF IP pin-out requirements for the Intel® Agilex™ Hard Processor Subsystem (HPS) are more restrictive than for a non-HPS memory interface. The HPS EMIF IP defines a fixed pin-out in the Intel® Quartus® Prime Pro Edition IP file (.qip), based on the IP configuration.
  • QDR-IV is not supported with HPS.

Observe the following general guidelines when placing pins for your Intel® Agilex™ external memory interface:

  1. Ensure that the pins of a single external memory interface reside on the same edge I/O.
  2. An external memory interface can occupy one or more banks on the same edge. When an interface must occupy multiple banks, ensure that those banks are adjacent to one another.
    • If an I/O bank is shared between two interfaces—meaning that two sub-banks belong to two different EMIF interfaces—then both the interfaces must share the same voltage.
    • Sharing of I/O lanes within a sub-bank for two different EMIF interfaces is not permitted; I/O lanes within a sub-bank can be assigned to one EMIF interface only.
  3. Any pin in the same bank that is not used by an external memory interface may not be available for use as a general purpose I/O pin:
    • For fabric EMIF, unused pins in an I/O lane assigned to an EMIF interface cannot be used as general-purpose I/O pins. In the same sub-bank, pins in an I/O lane that is not assigned to an EMIF interface, can be used as general-purpose I/O pins.
    • For HPS EMIF, unused pins in an I/O lane assigned to an EMIF interface cannot be used as general-purpose I/O pins. In the same sub-bank, pins in an I/O lane that is not assigned to an EMIF interface cannot be used as general-purpose I/O pins either. Refer to Restrictions on I/O Bank Usage for Intel® Agilex™ EMIF IP with HPS for more information.
  4. All address and command pins and their associated clock pins (CK and CK#) must reside within a single sub-bank. The sub-bank containing the address and command pins is identified as the address and command sub-bank.
  5. To minimize latency, when the interface uses more than two sub-banks, you must select the center sub-bank as the address and command sub-bank.
  6. The address and command pins and their associated clock pins in the address and command bank must follow a fixed pin-out scheme, as defined in the Intel® Agilex™ External Memory Interface Pin Information file, which is available here: Pin-Out Files for Intel FPGA Devices.
  7. An unused I/O lane in the address and command sub-bank can serve to implement a data group, such as a x8 DQS group. The data group must be from the same controller as the address and command signals.
  8. An I/O lane must not be used by both address and command pins and data pins.
  9. Place read data groups according to the DQS grouping in the pin table and Pin Planner. Read data strobes (such as DQS and DQS#) or read clocks (such as CQ and CQ# / QK and QK#) must reside at physical pins capable of functioning as DQS/CQ and DQSn/CQn for a specific read data group size. You must place the associated read data pins (such as DQ and Q), within the same group.
  10. One of the sub-banks in the device (typically the sub-bank within corner bank 3A) may not be available if you use certain device configuration schemes. For some schemes, there may be an I/O lane available for EMIF data group.
    • AVST-8 – This is contained entirely within the SDM, therefore all lanes of sub-bank 3A can be used by the external memory interface.
    • AVST-32 – Lanes 0, 1, 2, and 3 are all effectively occupied and are not usable by the external memory interface.
    • AVST-16 – Lanes 0, 1, and 3 are not usable by the external memory interface. However, lane 2 contains SDM_MISSION_DATA[25:16]. If SDM_MISSION_DATA[25:16] is not required for AVSTx16, then Lane 2 is available for use by the external memory interface.
  11. Sub-banks and I/O banks cannot be shared by two different memory interfaces.