3.11.1. PHY Registers

E-tile Hard IP User Guide: E-Tile Hard IP for Ethernet and E-Tile CPRI PHY Intel® FPGA IPs

Download PDF

ID 683468

Date 12/28/2022

Version

Public

A newer version of this document is available. Customers should click here to go to the newest version.

Visible to Intel only — GUID: zmr1556288467394

Ixiasoft

View Details

3.11.1. PHY Registers

Table 107. PHY Registers
Address	Bit	Name	Description	Access	Reset
0x310	5	`set_data_lock`	Set data lock 1: Force PLL to lock to data.	`RW`	`0x0`
	4	`set_ref_lock`	Set ref lock 1: Force PLL to lock to reference.	`RW`	`0x0`
	2	`soft_rx_rst`	Soft RXP Reset 1: Resets the RX PCS and RX MAC.	`RW`	`0x0`
	1	`soft_tx_rst`	Soft TXP Reset 1: Resets the TX PCS and TX MAC.	`RW`	`0x0`
	0	`eio_sys_rst`	Ethernet IO System Reset 1: Resets the IP core (TX and RX MACs, Ethernet reconfiguration registers, PCS, and transceivers).	`RW`	`0x0`
0x321	3:0	`eio_freq_lock`	Clock Data Recovery (CDR) PLL locked 1: Corresponding physical lane's CDR has locked to reference for 10 and 25G links.	`RO`	`0x0`
0x30E	9	`use_aligner`	Use RX PCS Alignment 1:RX PCS has aligner turned on to align incoming data. 0: The RX PCS expects to receive aligned data, and its internal alignment logic is bypassed. After power on, this register defaults to 0 After `i_csr_rst_n`, this register is set depending on the Select Ethernet IP Layers parameter In all modes that include RS-FEC, this register is set to 0 In modes that do not include RS-FEC, this register is set to 1	`RW`	`0x0`
0x322	0	`tx_pcs_ready`	TX Ready 1: TX Datapath is out of reset, stable, and ready for use.	`RO`	`0x0`
0x323	19:0	`frmerr`	Frame error(s) detected 1: A frame error was detected on the corresponding lane. For single lanes, only bit 0 is used This bit is sticky, and must be cleared by asserting `sclr_frame_error`	`RO`	`0x0`
0x324	0	`clr_frmerr`	Clear PHY frame error(s). 1: Return all sticky frame error bits to 0.	`RW`	`0x0`
0x325	19	`rx_pcs_in_rst`	Reset RX PCS 1: Reset RX PCS. Defaults to 0 after power-up and `i_csr_rst_n` asserted	`RW`	`0x1`
	17	`tx_pcs_in_rst`	Reset TX PCS 1: Reset TX PCS. Defaults to 0 after power-up and `i_csr_rst_n` asserted.	`RW`	`0x1`
	14	`force_hip_ready`	Override Hard IP ready 1: Assert `force_hip_ready`, even if all the conditions for Hard IP ready have not been met. Note that one of the conditions for `force_hip_ready` is the completion of configuration loading. If there is a problem with the configuration logic, `force_hip_ready` may be prevented from taking effect This feature is provided for test and debug only Defaults to 0 after power-up and `i_csr_rst_n` asserted.	`RW`	`0x0`
	2	`trst`	TX Datapath reset 1: Hold TX datapath in reset, including TX PLD, TX MAC, and TX PCS. Performs same function as the `i_tx_rst_n` port The IP core asserts `o_tx_rst` signal when this reset is active Does not reset TX MAC statistics Space the assertion and deassertion of reset to prevent sudden changes in power consumption Defaults to 0 after power-up and `i_csr_rst_n` asserted.	`RW`	`0x0`
	0	`rrst`	RX Datapath reset 1: Hold RX datapath in reset, including RX PLD, RX MAC, and RX PCS. Performs same function as the `i_rx_rst_n` port The IP core asserts `o_rx_rst` when this reset is active Does not reset RX MAC statistics Space the assertion and deassertion of reset to prevent sudden changes in power consumption Defaults to 1 after power-up Defaults to 0 after `i_csr_rst_n` asserted.	`RW`	`0x0`
0x326	1	`hi_ber`	Hi-BER 1: One or more virtual lanes are in Hi-BER state.	`RO`	`0x0`
0x326	0	`rx_aligned`	RX PCS fully aligned 1: The RX PCS is fully aligned and ready to start decoding data	`RO`	`0x0`
0x32A	31:0	`count`	BER Count 32-bit count that increments each time the core enters `BER_BAS_SH` state. Rolls over when maximum count is reached Clears when the channel is reset Can be captured using snapshot or RX shadow request	`RO`	`0x0`
0x32B	19:16	`ehip_rx_transfer_ready`	EHIP/ELANE RX Channels Transfer Ready Status 1: `transfer_ready` is 1.	`RO`	0x0
0x32B	3:0	`ehip_tx_transfer_ready`	EHIP/ELANE TX Channels Transfer Ready Status 1: `transfer_ready` is 1.	`RO`	0x0
0x341	31:0	`khz_rx`	Recovered clock frequency Recovered clock frequency/100, in KHz.	`RO`	`0x0`
0x342	31:0	`khz_tx`	TX clock frequency TX clock frequency/100, in KHz.	`RO`	`0x0`
0x351	24	`err_tx_avst_fifo_overflow`	TX AVST FIFO Overflow Indicates that the FIFO was written while full Overflow would never happen—if it does, this indicates a problem with the way `i_valid` is being driven Once asserted this bit holds value until the `i_clear_internal_error` port is asserted to clear it This bit doesn't need to be polled— the IP asserts `o_internal_err` signal if this signal goes high	`RO`	`0x0`
	23	`err_tx_avst_fifo_empty`	TX AVST FIFO ran empty unexpectedly Asserts when the TX FIFO runs empty (regardless of read enable) Does not apply when in MAC mode Empty should never happen—if it does, this indicates a problem with the way `i_valid` is being driven	`RO`	`0x1`
	22	`err_tx_avst_fifo_underflow`	TX AVST FIFO Underflow Indicates that the FIFO was read when empty after steady state reading was established Underflow should never happen—if it does, this indicates a problem with the way `i_valid` is being driven Once asserted this bit holds value until the `i_clear_internal_error` port is asserted to clear it, or the TX datapath is reset This bit doesn't need to be polled—`o_internal_err` is asserted if this signal goes high	`RO`	`0x0`
0x360	20	`use_hi_ber_monitor`	Enable Hi-BER Monitor 0: Turn off Hi-BER monitor 1: Turn on Hi-BER monitor The Hi-BER monitor is turned on by default because it is used for standard compliance Hi-BER is needed to support Auto-Negotiation, and is generally used to report poor link conditions When the Hi-BER monitor is turned on, if a Hi-BER condition is detected, the PCS replaces incoming data with Local Fault blocks Disable the Hi-BER monitor if you need to monitor RX data while in a Hi-BER state At power-on, this register defaults to 0 After `i_csr_rst_n` is asserted, the register is set to the value given by the `hi_ber_monitor` module parameter	`RW`	`0x0`
0x37A	20:0	`cycles`	Timer window for BER measurements Sets the timer window for BER measurements in clock cycles. The Ethernet Standard (IEEE 802.3) defines the required times for Hi-BER measurements for each rate. These times must be converted to clock cycles with the accuracy of within +1% and -25% of the specified times. Note: If the clock rate you are using is different from the clock rate used to calculate the cycle count, you need to scale the cycle count. 100GBASE-R4: 21'd201415 (from Clause 82, 0.5ms +1%,-25% at 402.3 MHz 25GBASE-R1: 21'd806451 (from Clause 107, 2.0 ms +1%, -25% at 402.3 MHz 10GBASE-R1: 21'd20141 (from Clause 49, 0.125ms +1%, -25% at 161.13 MHz 10GBASE-R1: 21'd50403 (from Clause 49, 0.125ms +1%, -25% at 402.83 MHz The RX PCS must be reset after changing this value.	`RW`	`0x312C7`
0x37B	6:0	`count`	Hi-BER Frame Errors Sets the BER count that triggers `hi_ber`. The Ethernet Standard (IEEE 802.3) defines the appropriate setting for `ber_invalid_count` based on rate. 100GBASE-R4: 7'd97 (from Clause 82) 25GBASE-R1: 7'd97 (from Clause 107) 10GBASE-R1: 7'd16 (from Clause 49) The RX PCS must be reset after changing this value.	`RW`	`0x61`
0x37C	31:0	`count`	Error block count Counts the number of error blocks produced by the RX PCS decoder Valid only when the RX PCS decoder is used and alignment is achieved The error blocks can be received from the remote link, or generated by violations of the Ethernet Standard 64B66B encoding specification The counter is 32-bit wide and rolls over when the max count is reached The counter is reset when the RX datapath is reset, or the RX PCS is reset	`RO`	`0x0`

Select Your Language

Using Intel.com Search

Quick Links

Recent Searches

Advanced Search

Only search in

E-tile Hard IP User Guide: E-Tile Hard IP for Ethernet and E-Tile CPRI PHY Intel® FPGA IPs

3.11.1. PHY Registers