Visible to Intel only — GUID: nle1657031228094
Ixiasoft
1. About the Video and Vision Processing Suite
2. Getting Started with the Video and Vision Processing IPs
3. Video and Vision Processing IPs Functional Description
4. Video and Vision Processing IP Interfaces
5. Video and Vision Processing IP Registers
6. Video and Vision Processing IPs Software Programming Model
7. Protocol Converter IP
8. 1D LUT IP
9. 3D LUT IP
10. Adaptive Noise Reduction IP
11. Advanced Test Pattern Generator IP
12. AXI-Stream Broadcaster IP
13. Bits per Color Sample Adapter IP
14. Black Level Correction IP
15. Black Level Statistics IP
16. Chroma Key IP
17. Chroma Resampler IP
18. Clipper IP
19. Clocked Video Input IP
20. Clocked Video to Full-Raster Converter IP
21. Clocked Video Output IP
22. Color Plane Manager IP
23. Color Space Converter IP
24. Defective Pixel Correction IP
25. Deinterlacer IP
26. Demosaic IP
27. FIR Filter IP
28. Frame Cleaner IP
29. Full-Raster to Clocked Video Converter IP
30. Full-Raster to Streaming Converter IP
31. Genlock Controller IP
32. Generic Crosspoint IP
33. Genlock Signal Router IP
34. Guard Bands IP
35. Histogram Statistics IP
36. Interlacer IP
37. Mixer IP
38. Pixels in Parallel Converter IP
39. Scaler IP
40. Stream Cleaner IP
41. Switch IP
42. Text Box IP
43. Tone Mapping Operator IP
44. Test Pattern Generator IP
45. Unsharp Mask IP
46. Video and Vision Monitor Intel FPGA IP
47. Video Frame Buffer IP
48. Video Frame Reader Intel FPGA IP
49. Video Frame Writer Intel FPGA IP
50. Video Streaming FIFO IP
51. Video Timing Generator IP
52. Vignette Correction IP
53. Warp IP
54. White Balance Correction IP
55. White Balance Statistics IP
56. Design Security
57. Document Revision History for Video and Vision Processing Suite User Guide
31.4.1. Achieving Genlock Controller Free Running (for Initialization or from Lock to Reference Clock N)
31.4.2. Locking to Reference Clock N (from Genlock Controller IP free running)
31.4.3. Setting the VCXO hold over
31.4.4. Restarting the Genlock Controller IP
31.4.5. Locking to Reference Clock N New (from Locking to Reference Clock N Old)
31.4.6. Changing to Reference Clock or VCXO Base Frequencies (switch between p50 and p59.94 video formats and vice-versa)
31.4.7. Disturbing a Reference Clock (a cable pull)
Visible to Intel only — GUID: nle1657031228094
Ixiasoft
19.2. Initializing the Clocked Video Input IP
The IP provides an Avalon memory-mapped interface, which you can use as a control interface to configure the IP. Initially, the IP is disabled and does not transmit any data or video. However, the Clocked Video Input IP still detects the format of the clocked video input and accepts data on the input video interface.
To start the output of the IP:
- Write a 1 to control register bit 0 to enable the clocked video input block
- Write a 1 to control register bit 4 to enable Vsync and Hsync autopolarity detection.
- Optionally, write a 1 to control register bit 3 to enable the frame cleaner logic.
- Optionally, write the minimum expected number of frames for F0 and F1 to control register bits 23:16 to enable autodetect interlaced video format mode. If you write zeros to this set of bits, the IP does not automatically auto-detect video interlaced formats.
- Write the expected output video height and width values to ref_lock_cfg1 register. The IP only starts transmitting video on the output interface when the values on ref_lock_cfg1 matches the values on registers active_line_count and total_line_count.
- Write the expected number of frames and output video lines values to ref_lock_cfg2 register. The IP only starts transmitting video on the output interface when the values on ref_lock_cfg2 are matched.
- Alternatively, if you write zeros to ref_lock_cfg1 and ref_lock_cfg2, the IP does not try to match any specific output video resolution values and immediately produces video.
- Optionally, set the values for each of the color planes that the frame cleaner use to do the padding on the output video frame in case a cable is pulled.
- Read status register bit 4. When this bit is 1, the IP starts transmitting video. The transmission starts on the next start of frame boundary.