1. About the Video and Image Processing Suite
2. Avalon Streaming Video
3. Clocked Video
4. VIP Run-Time Control
5. Getting Started
6. VIP Connectivity Interfacing
7. Clocked Video Interface IPs
8. 2D FIR II IP Core
9. Mixer II IP Core
10. Clipper II IP Core
11. Color Plane Sequencer II IP Core
12. Color Space Converter II IP Core
13. Chroma Resampler II IP Core
14. Control Synchronizer IP Core
15. Deinterlacer II IP Core
16. Frame Buffer II IP Core
17. Gamma Corrector II IP Core
18. Configurable Guard Bands IP Core
19. Interlacer II IP Core
20. Scaler II IP Core
21. Switch II IP Core
22. Test Pattern Generator II IP Core
23. Trace System IP Core
24. Warp Lite Intel FPGA IP
25. Avalon-ST Video Stream Cleaner IP Core
26. Avalon-ST Video Monitor IP Core
27. VIP IP Core Software Control
28. Security Considerations
29. Video and Image Processing Suite User Guide Archives
30. Document Revision History for the Video and Image Processing Suite User Guide
A. Avalon-ST Video Verification IP Suite
7.1. Supported Features for Clocked Video Output II IP
7.2. Control Port
7.3. Clocked Video Input IP Format Detection
7.4. Clocked Video Output IP Video Modes
7.5. Clocked Video Output II Latency Mode
7.6. Generator Lock
7.7. Underflow and Overflow
7.8. Timing Constraints
7.9. Handling Ancillary Packets
7.10. Modules for Clocked Video Input II IP Core
7.11. Clocked Video Input II Signals, Parameters, and Registers
7.12. Clocked Video Output II Signals, Parameters, and Registers
15.1. Deinterlacing Algorithm Options
15.2. Deinterlacing Algorithms
15.3. Run-time Control
15.4. Pass-Through Mode for Progressive Frames
15.5. Cadence Detection (Motion Adaptive Deinterlacing Only)
15.6. Avalon-MM Interface to Memory
15.7. Motion Adaptive Mode Bandwidth Requirements
15.8. Avalon-ST Video Support
15.9. 4K Video Passthrough Support
15.10. Behavior When Unexpected Fields are Received
15.11. Handling of Avalon-ST Video Control Packets
15.12. Deinterlacer II Parameter Settings
15.13. Deinterlacing Control Registers
A.3.1. c_av_st_video_control
A.3.2. c_av_st_video_data
A.3.3. c_av_st_video_file_io
A.3.4. c_av_st_video_item
A.3.5. c_av_st_video_source_sink_base
A.3.6. c_av_st_video_sink_bfm_’SINK
A.3.7. c_av_st_video_source_bfm_’SOURCE
A.3.8. c_av_st_video_user_packet
A.3.9. c_pixel
A.3.10. av_mm_transaction
A.3.11. av_mm_master_bfm_`MASTER_NAME
A.3.12. av_mm_slave_bfm_`SLAVE_NAME
A.3.13. av_mm_control_register
A.3.14. av_mm_control_base
26.2. Monitor Settings
The capture settings panel of the trace table provides convenient access to the monitor settings.
You can change the monitor settings with the trace_write_monitor and trace_read_monitor TCL commands. At the hardware level, you can access the register map through the control Avalon-MM slave port of the monitor component.
The capture settings panel offers three options.
- Enable—sends of statistics and sampled data.
- Disable—blocks the sending of statistics and sampled data.
- Enable with pixel capture— the monitor starts sampling the actual pixel data in the video data packets, and displays the captured pixels in the detailed event view.
The Capture Rate per 1000000 parameter controls the pixel percentage from randomly sampled data packets. A higher capture rate (closer to 1000000) displays a higher pixel percentage in the sample.
- If the capture rate is 5000 out of 1000000 pixels, the monitor attempts to sample one in every 200 pixels.
- If the monitor captures all the 1000000 pixels available, the monitor samples every pixel in the image.
- If there is not enough bandwidth to sample every pixel in the image, the reconstructed image may have a black and purple checkerboard pattern.
Assign a smaller capture rate value to allow the trace system to send all the debugging information through and avoid the checkerboard pattern.