Stratix® V Device Handbook: Volume 1: Device Interfaces and Integration
ID
683665
Date
10/18/2023
Public
1. Logic Array Blocks and Adaptive Logic Modules in Stratix V Devices
2. Embedded Memory Blocks in Stratix V Devices
3. Variable Precision DSP Blocks in Stratix V Devices
4. Clock Networks and PLLs in Stratix V Devices
5. I/O Features in Stratix V Devices
6. High-Speed Differential I/O Interfaces and DPA in Stratix® V Devices
7. External Memory Interfaces in Stratix V Devices
8. Configuration, Design Security, and Remote System Upgrades in Stratix V Devices
9. SEU Mitigation for Stratix V Devices
10. JTAG Boundary-Scan Testing in Stratix V Devices
11. Power Management in Stratix V Devices
2.1. Types of Embedded Memory
2.2. Embedded Memory Design Guidelines for Stratix V Devices
2.3. Embedded Memory Features
2.4. Embedded Memory Modes
2.5. Embedded Memory Clocking Modes
2.6. Parity Bit in Memory Blocks
2.7. Byte Enable in Embedded Memory Blocks
2.8. Memory Blocks Packed Mode Support
2.9. Memory Blocks Address Clock Enable Support
2.10. Memory Blocks Asynchronous Clear
2.11. Memory Blocks Error Correction Code Support
2.12. Embedded Memory Blocks in Stratix V Devices Revision History
4.2.1. PLL Physical Counters in Stratix V Devices
4.2.2. PLL Locations in Stratix® V Devices
4.2.3. PLL Migration Guidelines
4.2.4. Fractional PLL Architecture
4.2.5. PLL Cascading
4.2.6. PLL External Clock I/O Pins
4.2.7. PLL Control Signals
4.2.8. Clock Feedback Modes
4.2.9. Clock Multiplication and Division
4.2.10. Programmable Phase Shift
4.2.11. Programmable Duty Cycle
4.2.12. Clock Switchover
4.2.13. PLL Reconfiguration and Dynamic Phase Shift
5.1. I/O Standards Support in Stratix V Devices
5.2. I/O Design Guidelines for Stratix V Devices
5.3. I/O Banks in Stratix® V Devices
5.4. I/O Banks Groups in Stratix V Devices
5.5. I/O Element Structure in Stratix V Devices
5.6. Programmable IOE Features in Stratix® V Devices
5.7. On-Chip I/O Termination in Stratix® V Devices
5.8. I/O Termination Schemes for Stratix® V Devices
5.9. I/O Features in Stratix V Devices Revision History
5.6.1. Programmable Current Strength
5.6.2. Programmable Output Slew Rate Control
5.6.3. Programmable IOE Delay
5.6.4. Programmable Output Buffer Delay
5.6.5. Programmable Pre-Emphasis
5.6.6. Programmable Differential Output Voltage
5.6.7. Open-Drain Output
5.6.8. Bus-Hold Circuitry
5.6.9. Pull-up Resistor
5.7.1. RS OCT without Calibration in Stratix® V Devices
5.7.2. RS OCT with Calibration in Stratix® V Devices
5.7.3. RT OCT with Calibration in Stratix® V Devices
5.7.4. Dynamic OCT in Stratix® V Devices
5.7.5. LVDS Input RD OCT in Stratix V Devices
5.7.6. OCT Calibration Block in Stratix V Devices
5.7.7. OCT Calibration in Power-Up Mode
5.7.8. OCT Calibration in User Mode
6.1. Dedicated High-Speed Circuitries in Stratix® V Devices
6.2. High-Speed I/O Design Guidelines for Stratix® V Devices
6.3. Differential Transmitter in Stratix V Devices
6.4. Differential Receiver in Stratix V Devices
6.5. Source-Synchronous Timing Budget
6.6. High-Speed Differential I/O Interfaces and DPA in Stratix® V Devices Revision History
7.3.1. UniPHY IP
7.3.2. External Memory Interface Datapath
7.3.3. DQS Phase-Shift Circuitry
7.3.4. Phase Offset Control
7.3.5. PHY Clock (PHYCLK) Networks
7.3.6. DQS Logic Block
7.3.7. Leveling Circuitry
7.3.8. Dynamic OCT Control
7.3.9. IOE Registers
7.3.10. Delay Chains
7.3.11. I/O and DQS Configuration Blocks
8.1. Enhanced Configuration and Configuration via Protocol
8.2. MSEL Pin Settings
8.3. Configuration Sequence
8.4. Configuration Timing Waveforms
8.5. Device Configuration Pins
8.6. Fast Passive Parallel Configuration
8.7. Active Serial Configuration
8.8. Using EPCS and EPCQ Devices
8.9. Passive Serial Configuration
8.10. JTAG Configuration
8.11. Configuration Data Compression
8.12. Remote System Upgrades
8.13. Design Security
8.14. Configuration, Design Security, and Remote System Upgrades in Stratix V Devices Revision History
10.1. BST Operation Control
10.2. I/O Voltage for JTAG Operation
10.3. Performing BST
10.4. Enabling and Disabling IEEE Std. 1149.1 BST Circuitry
10.5. Guidelines for IEEE Std. 1149.1 Boundary-Scan Testing
10.6. IEEE Std. 1149.1 Boundary-Scan Register
10.7. IEEE Std. 1149.6 Boundary-Scan Register
10.8. JTAG Boundary-Scan Testing inStratix V Devices Revision History
8.12.1. Configuration Images
Each Stratix® V device in your system requires one factory image. The factory image is a user-defined configuration image that contains logic to perform the following:
- Processes errors based on the status provided by the dedicated remote system upgrade circuitry.
- Communicates with the remote host, receives new application images, and stores the images in the local non-volatile memory device.
- Determines the application image to load into the Stratix® V device.
- Enables or disables the user watchdog timer and loads its time-out value.
- Instructs the dedicated remote system upgrade circuitry to start a reconfiguration cycle.
You can also create one or more application images for the device. An application image contains selected functionalities to be implemented in the target device.
Store the images at the following locations in the EPCS or EPCQ devices:
- Factory configuration image— PGM[23..0] = 24'h000000 start address on the EPCS or EPCQ device.
- Application configuration image—any sector boundary. Altera recommends that you store only one image at one sector boundary.
When you are using EPCQ 256, ensure that the application configuration image address granularity is 32'h00000100. The granularity requirement is having the most significant 24 bits of the 32 bits start address written to PGM[23..0] bits.
Note: If you are not using the Intel® Quartus® Prime software or SRunner software for EPCQ 256 programming, put your EPCQ 256 device into four-byte addressing mode before you program and configure your device.