Cyclone V Device Handbook: Volume 2: Transceivers

Download PDF
ID 683586
Date 10/24/2018
Public
Document Table of Contents
Document Table of Contents x
1. Transceiver Architecture in Cyclone V Devices 2. Transceiver Clocking in Cyclone V Devices 3. Transceiver Reset Control in Cyclone V Devices 4. Transceiver Protocol Configurations in Cyclone V Devices 5. Transceiver Custom Configurations in Cyclone V Devices 6. Transceiver Loopback Support 7. Dynamic Reconfiguration in Cyclone V Devices
1. Transceiver Architecture in Cyclone V Devices x
1.1. Architecture Overview 1.2. PMA Architecture 1.3. PCS Architecture 1.4. Channel Bonding 1.5. PLL Sharing 1.6. Document Revision History
1.1. Architecture Overview x
1.1.1. Transceiver Banks 1.1.2. 6.144 Gbps CPRI Support Capability in GT Devices 1.1.3. Transceiver Channel Architecture
1.1.1. Transceiver Banks x
1.1.1.1. Usage Restrictions on Specific Channels
1.2. PMA Architecture x
1.2.1. Transmitter PMA Datapath 1.2.2. Receiver PMA Datapath 1.2.3. Transmitter PLL 1.2.4. Clock Divider 1.2.5. Calibration Block
1.2.1. Transmitter PMA Datapath x
1.2.1.1. Serializer 1.2.1.2. Transmitter Buffer
1.2.1.1. Serializer x
1.2.1.1.1. Transmitter Polarity Inversion 1.2.1.1.2. Bit Reversal
1.2.1.2. Transmitter Buffer x
1.2.1.2.1. Transmitter Buffer Features and Capabilities 1.2.1.2.2. Programmable Transmitter Analog Settings 1.2.1.2.3. Programmable Transmitter VCM 1.2.1.2.4. Programmable Transmitter Differential OCT 1.2.1.2.5. Transmitter Protocol Specific
1.2.2. Receiver PMA Datapath x
1.2.2.1. Receiver Buffer 1.2.2.2. Deserializer
1.2.2.1. Receiver Buffer x
1.2.2.1.1. Programmable CTLE and DC Gain 1.2.2.1.2. Programmable Receiver VCM 1.2.2.1.3. Programmable Receiver Differential On-Chip Termination 1.2.2.1.4. Signal Threshold Detection Circuitry
1.2.2.2. Deserializer x
1.2.2.2.1. Clock-slip
1.2.3. Transmitter PLL x
1.2.3.1. Channel PLL Architecture 1.2.3.2. Channel PLL as CDR PLL 1.2.3.3. Channel PLL as a CMU PLL 1.2.3.4. fPLL as a Transmitter PLL
1.2.3.2. Channel PLL as CDR PLL x
1.2.3.2.1. Lock-to-Reference Mode 1.2.3.2.2. Lock-to-Data Mode 1.2.3.2.3. CDR PLL in Automatic Lock Mode 1.2.3.2.4. CDR PLL in Manual Lock Mode
1.3. PCS Architecture x
1.3.1. Transmitter PCS Datapath 1.3.2. Receiver PCS Datapath
1.3.1. Transmitter PCS Datapath x
1.3.1.1. Transmitter Phase Compensation FIFO 1.3.1.2. Byte Serializer 1.3.1.3. 8B/10B Encoder 1.3.1.4. Transmitter Bit-Slip
1.3.1.1. Transmitter Phase Compensation FIFO x
1.3.1.1.1. Registered Mode 1.3.1.1.2. Phase Compensation Mode
1.3.1.2. Byte Serializer x
1.3.1.2.1. Byte Serializer in Single-Width Mode 1.3.1.2.2. Byte Serializer in Double-Width Mode
1.3.1.3. 8B/10B Encoder x
1.3.1.3.1. 8B/10B Encoder in Single-Width Mode 1.3.1.3.2. 8B/10B Encoder in Double-Width Mode 1.3.1.3.3. Running Disparity Control 1.3.1.3.4. Control Code Encoding 1.3.1.3.5. Reset Condition 1.3.1.3.6. Encoder Output During Reset Sequence
1.3.2. Receiver PCS Datapath x
1.3.2.1. Word Aligner 1.3.2.2. Rate Match FIFO 1.3.2.3. 8B/10B Decoder 1.3.2.4. Byte Deserializer 1.3.2.5. Byte Ordering 1.3.2.6. Receiver Phase Compensation FIFO
1.3.2.1. Word Aligner x
1.3.2.1.1. Word Aligner Options and Behaviors 1.3.2.1.2. Word Aligner in Manual Alignment Mode 1.3.2.1.3. Word Aligner in Bit-Slip Mode 1.3.2.1.4. Word Aligner in Automatic Synchronization State Machine Mode 1.3.2.1.5. Word Aligner in Automatic Synchronization State Machine Mode with a 10-Bit PMA-PCS Interface Configuration 1.3.2.1.6. Word Aligner Operations in Deterministic Latency State Machine Mode 1.3.2.1.7. Programmable Run-Length Violation Detection 1.3.2.1.8. Receiver Polarity Inversion 1.3.2.1.9. Bit Reversal 1.3.2.1.10. Receiver Byte Reversal
1.3.2.3. 8B/10B Decoder x
1.3.2.3.1. 8B/10B Decoder in Single-Width Mode 1.3.2.3.2. 8B/10B Decoder in Double-Width Mode 1.3.2.3.3. Control Code Group Detection
1.3.2.4. Byte Deserializer x
1.3.2.4.1. Byte Deserializer in Single-Width Mode 1.3.2.4.2. Byte Deserializer in Double-Width Mode
1.3.2.5. Byte Ordering x
1.3.2.5.1. Byte Ordering in Single-Width Mode 1.3.2.5.2. Byte Ordering in Double-Width Mode 1.3.2.5.3. Word Aligner-Based Ordering Mode 1.3.2.5.4. Manual Ordering Mode
1.3.2.6. Receiver Phase Compensation FIFO x
1.3.2.6.1. Registered Mode
2. Transceiver Clocking in Cyclone V Devices x
2.1. Input Reference Clocking 2.2. Internal Clocking 2.3. FPGA Fabric–Transceiver Interface Clocking 2.4. Document Revision History
2.1. Input Reference Clocking x
2.1.1. Dedicated Reference Clock Pins 2.1.2. Fractional PLL (fPLL)
2.1.1. Dedicated Reference Clock Pins x
2.1.1.1. Dedicated refclk Using the Reference Clock Network 2.1.1.2. Dual-Purpose RX/refclk Pins
2.2. Internal Clocking x
2.2.1. Transmitter Clock Network 2.2.2. Transmitter Clocking 2.2.3. Receiver Clocking
2.2.2. Transmitter Clocking x
2.2.2.1. Non-Bonded Channel Configurations 2.2.2.2. Bonded Channel Configurations
2.2.3. Receiver Clocking x
2.2.3.1. Receiver Non-Bonded Channel Configurations 2.2.3.2. Receiver Bonded Channel Configurations
2.3. FPGA Fabric–Transceiver Interface Clocking x
2.3.1. Transceiver Datapath Interface Clocking 2.3.2. Transmitter Datapath Interface Clocking 2.3.3. Receiver Datapath Interface Clock
2.3.2. Transmitter Datapath Interface Clocking x
2.3.2.1. Quartus II-Software Selected Transmitter Datapath Interface Clock 2.3.2.2. Selecting a Transmitter Datapath Interface Clock
2.3.3. Receiver Datapath Interface Clock x
2.3.3.1. Quartus II Software-Selected Receiver Datapath Interface Clock 2.3.3.2. Selecting a Receiver Datapath Interface Clock
3. Transceiver Reset Control in Cyclone V Devices x
3.1. PHY IP Embedded Reset Controller 3.2. User-Coded Reset Controller 3.3. Transceiver Reset Using Avalon Memory Map Registers 3.4. Clock Data Recovery in Manual Lock Mode Resetting the Transceiver During Dynamic Reconfiguration 3.6. Transceiver Blocks Affected by the Reset and Powerdown Signals 3.7. Transceiver Power-Down 3.8. Document Revision History
3.1. PHY IP Embedded Reset Controller x
3.1.1. Embedded Reset Controller Signals 3.1.2. Resetting the Transceiver with the PHY IP Embedded Reset Controller During Device Power-Up 3.1.3. Resetting the Transceiver with the PHY IP Embedded Reset Controller During Device Operation
3.2. User-Coded Reset Controller x
3.2.1. User-Coded Reset Controller Signals 3.2.2. Resetting the Transmitter with the User-Coded Reset Controller During Device Power-Up 3.2.3. Resetting the Transmitter with the User-Coded Reset Controller During Device Operation 3.2.4. Resetting the Receiver with the User-Coded Reset Controller During Device Power-Up Configuration 3.2.5. Resetting the Receiver with the User-Coded Reset Controller During Device Operation
3.3. Transceiver Reset Using Avalon Memory Map Registers x
3.3.1. Transceiver Reset Control Signals Using Avalon Memory Map Registers
3.4. Clock Data Recovery in Manual Lock Mode x
3.4.1. Control Settings for CDR Manual Lock Mode 3.4.2. Resetting the Transceiver in CDR Manual Lock Mode
4. Transceiver Protocol Configurations in Cyclone V Devices x
4.1. PCI Express 4.2. Gigabit Ethernet 4.3. XAUI 4.4. Serial Digital Interface 4.5. Serial Data Converter (SDC) JESD204 4.6. SATA and SAS Protocols 4.7. Deterministic Latency Protocols—CPRI and OBSAI 4.8. Document Revision History
4.1. PCI Express x
4.1.1. PCIe Transceiver Datapath 4.1.2. PCIe Supported Features 4.1.3. PCIe Supported Configurations and Placement Guidelines
4.1.2. PCIe Supported Features x
4.1.2.1. PIPE Interface 4.1.2.2. Transmitter Electrical Idle Generation 4.1.2.3. Power State Management 4.1.2.4. 8B/10B Encoder Usage for Compliance Pattern Transmission Support 4.1.2.5. Receiver Status 4.1.2.6. Receiver Detection 4.1.2.7. Clock Rate Compensation Up to ±300 ppm 4.1.2.8. PCIe Reverse Parallel Loopback
4.2. Gigabit Ethernet x
4.2.1. Gigabit Ethernet Transceiver Datapath
4.3. XAUI x
4.3.1. Transceiver Datapath in a XAUI Configuration 4.3.2. XAUI Supported Features 64-Bit SDR Interface to the MAC/RS 8B/10B Encoding/Decoding Transmitter and Receiver State Machines Synchronization Deskew Clock Compensation 4.3.3. Transceiver Clocking and Channel Placement Guidelines in XAUI Configuration
4.4. Serial Digital Interface x
4.4.1. Configurations Supported in SDI Mode 4.4.2. Serial Digital Interface Transceiver Datapath
4.7. Deterministic Latency Protocols—CPRI and OBSAI x
4.7.1. Latency Uncertainty Removal with the Phase Compensation FIFO in Register Mode 4.7.2. Channel PLL Feedback for Deterministic Relationship 4.7.3. CPRI and OBSAI 4.7.4. 6.144-Gbps Support Capability in Cyclone V GT Devices 4.7.5. CPRI Enhancements
5. Transceiver Custom Configurations in Cyclone V Devices x
5.1. Standard PCS Configuration 5.2. Standard PCS in Low Latency Configuration 5.3. Document Revision History
5.1. Standard PCS Configuration x
5.1.1. Custom Configuration Channel Options 5.1.2. Rate Match FIFO in Custom Configuration
5.1.2. Rate Match FIFO in Custom Configuration x
5.1.2.1. Rate Match FIFO Behaviors in Custom Single-Width Mode 5.1.2.2. Rate Match FIFO Behaviors in Custom Double-Width Mode
5.2. Standard PCS in Low Latency Configuration x
5.2.1. Low Latency Custom Configuration Channel Options
6. Transceiver Loopback Support x
6.1. Serial Loopback 6.2. Forward Parallel Loopback 6.3. PIPE Reverse Parallel Loopback 6.4. Reverse Serial Loopback 6.5. Reverse Serial Pre-CDR Loopback 6.6. Document Revision History
7. Dynamic Reconfiguration in Cyclone V Devices x
7.1. Dynamic Reconfiguration Features 7.2. Offset Cancellation 7.3. Transmitter Duty Cycle Distortion Calibration 7.4. PMA Analog Controls Reconfiguration 7.5. Dynamic Reconfiguration of Loopback Modes 7.6. Transceiver PLL Reconfiguration 7.7. Transceiver Channel Reconfiguration 7.8. Transceiver Interface Reconfiguration 7.9. Reduced .mif Reconfiguration 7.10. Unsupported Reconfiguration Modes 7.11. Document Revision History
1. Transceiver Architecture in Cyclone V Devices
2. Transceiver Clocking in Cyclone V Devices
3. Transceiver Reset Control in Cyclone V Devices
4. Transceiver Protocol Configurations in Cyclone V Devices
5. Transceiver Custom Configurations in Cyclone V Devices
6. Transceiver Loopback Support
7. Dynamic Reconfiguration in Cyclone V Devices

4.3.2. XAUI Supported Features

64-Bit SDR Interface to the MAC/RS

Clause 46 of the IEEE 802.3-2008 specification defines the XGMII interface between the XAUI PCS and the Ethernet MAC/RS. The specification requires each of the four XAUI lanes to transfer 8-bit data and 1-bit wide control code at both the positive and negative edge (DDR) of the 156.25 MHz interface clock.

Cyclone V transceivers and soft PCS solution in a XAUI configuration do not support the XGMII interface to the MAC/RS as defined in IEEE 802.3-2008 specification. Instead, they allow the transferring of 16-bit data and 2-bit control code on each of the four XAUI lanes, only at the positive edge (SDR) of the 156.25 MHz interface clock

Figure 84. Implementation of the XGMII Specification in Cyclone V Devices Configuration


8B/10B Encoding/Decoding

Each of the four lanes in a XAUI configuration support an independent 8B/10B encoder/decoder as specified in Clause 48 of the IEEE802.3-2008 specification. 8B/10B encoding limits the maximum number of consecutive 1s and 0s in the serial data stream to five, thereby ensuring DC balance as well as enough transitions for the receiver CDR to maintain a lock to the incoming data.

The XAUI PHY IP core provides status signals to indicate running disparity as well as the 8B/10B code group error.

Transmitter and Receiver State Machines

In a XAUI configuration, the Cyclone V soft PCS implements the transmitter and receiver state diagrams shown in Figure 48-6 and Figure 48-9 of the IEEE802.3-2008 specification.

In addition to encoding the XGMII data to PCS code groups, in conformance with the 10GBASE-X PCS, the transmitter state diagram performs functions such as converting Idle ||I|| ordered sets into Sync ||K||, Align ||A||, and Skip ||R|| ordered sets.

In addition to decoding the PCS code groups to XGMII data, in conformance with the 10GBASE-X PCS, the receiver state diagram performs functions such as converting Sync ||K||, Align ||A||, and Skip ||R|| ordered sets to Idle ||I|| ordered sets.

Synchronization

The word aligner block in the receiver PCS of each of the four XAUI lanes implements the receiver synchronization state diagram shown in Figure 48-7 of the IEEE802.3-2008 specification.

The XAUI PHY IP core provides a status signal per lane to indicate if the word aligner is synchronized to a valid word boundary.

Deskew

The lane aligner block in the receiver PCS implements the receiver deskew state diagram shown in Figure 48-8 of the IEEE 802.3-2008 specification.

The lane aligner starts the deskew process only after the word aligner block in each of the four XAUI lanes indicates successful synchronization to a valid word boundary.

The XAUI PHY IP core provides a status signal to indicate successful lane deskew in the receiver PCS.

Clock Compensation

The rate match FIFO in the receiver PCS datapath compensates up to ±100 ppm difference between the remote transmitter and the local receiver. It does so by inserting and deleting Skip ||R|| columns, depending on the ppm difference.

The clock compensation operation begins after:

  • The word aligner in all four XAUI lanes indicates successful synchronization to a valid word boundary.
  • The lane aligner indicates a successful lane deskew.

The rate match FIFO provides status signals to indicate the insertion and deletion of the Skip ||R|| column for clock rate compensation.

Level Two Title