8. Document Revision History for the JESD204B Intel® FPGA IP User...

JESD204B Intel® FPGA IP User Guide

Download PDF

ID 683442

Date 5/05/2023

Version

Public

A newer version of this document is available. Customers should click here to go to the newest version.

Visible to Intel only — GUID: bhc1411117154775

Ixiasoft

8. Document Revision History for the JESD204B Intel® FPGA IP User Guide

Document Version	Intel® Quartus® Prime Version	IP Version	Changes
2023.05.05	21.3	19.2.0	Updated Related Information list in JESD204B IP Quick Reference. Updated description in tables: syncn_sysref_ctrl Bit 10:3, csr_rbd_offset rx_err0 Bit 4, csr_lane_deskew_err
2022.08.18	21.3	19.2.0	Fixed broken link to the E-Tile Channel Placement Tool in the Pin Assignments section. Updated the JESD204B Intel® FPGA IP User Guide Archives section.
2022.05.18	21.3	19.2.0	Corrected IP Version from 19.3.0 to 19.2.0. Corrected the Intel® Quartus® Prime Version and Release Date descriptions in Table: JESD204B IP Release Information.
2021.12.09	21.3	19.2.0	Corrected the support final for Intel Agilex® 7 (E-tile) devices from Advance to Final in Table: Intel Device Family Support.
2021.11.01	21.3	19.2.0	Updated the description for Control and Status Registers clarify that registers that are Read-Writable must be protected to comply with Security Development Lifecycle (SDL) practices. Added support for QuestaSim* simulator. Updated for latest branding standards.
2021.06.23	20.2	19.2.0	Updated Transceiver Calibration Clock Source to include information about the `OSC_CLK_1` requirements for Intel Agilex® 7 and Intel® Stratix® 10 E-tile devices. Removed support for NCSim in the following tables: Table: Brief Information About the JESD204B IP Table: Simulation Setup Scripts Table: Simulation Run Scripts
2021.04.01	20.2	19.2.0	Updated Table: tx_status0 to correct the bit information for csr_dll_state and csr_dev_syncn.
2020.09.10	20.2	19.2.0	Added a new section, Transceiver Calibration Clock Source, which provides information about the `OSC_CLK` pin that provides the transceiver calibration clock source for Intel® Stratix® 10 L-tile and H-tile devices. Corrected the reset value for the receiver `csr_lane_alignment_err_link_reinit[13]` and `csr_lane_alignment_err_link_reinit[12]` registers. The reset value should be 0x1, not 0x0. Added a new section, Removing Irrelevant Signals and Adding E-Tile PHY Signals, which provides the steps to remove irrelevant PHY signals for Intel® Stratix® 10 E-tile designs. Added a link to the Removing Irrelevant Signals and Adding E-Tile PHY Signals section in the Creating a Debug File to Match Your Design Hierarchy section.
2020.06.30	19.4	19.2.0	Added the supported data rate for PMA speed grade 2 for Intel Agilex® 7 E-tile devices and for PMA speed grade 3 for Intel® Stratix® 10 E-tile devices in the Performance and Resource Utilization section. Corrected the offset address for the receiver `lane_ctrl_1` register. The offset address should be 0x8, not 0xC.
2020.03.03	19.4	19.2.0	Edited the Enable Bit reversal and Byte reversal parameter description in the JESD204B Intel® FPGA IP Parameters section.
2019.12.16	19.4	19.2.0	Updated the supported maximum data rate to 19.2 Gbps (for Intel Agilex® 7 devices) in the JESD204B IP Quick Reference, About the JESD204B Intel® FPGA IP , and Performance and Resource Utilization sections. Updated the maximum data rate value option to 19.2 Gbps for Intel Agilex® 7 devices for the Data Rate parameter and edited the Enable Bit reversal and Byte reversal parameter description in the JESD204B Intel® FPGA IP Parameters section.
2019.10.07	19.3	19.2.0	Added advance support for Intel Agilex® 7 devices. Updated the supported maximum data rate to 17.4 Gbps (for Intel Agilex® 7 devices) in the JESD204B IP Quick Reference and About the JESD204B Intel® FPGA IP sections. Updated the JESD204B Intel® FPGA IP Performance table in the Performance and Resource Utilization section with Intel Agilex® 7 devices information. Updated the maximum data rate value option to 17.4 Gbps for Intel Agilex® 7 devices in the JESD204B Intel® FPGA IP Parameters section. Added a reference link to the JESD204B Intel Agilex® 7 FPGA IP Design Example User Guide.
2019.05.27	19.1	19.1	Corrected typos in the Transmitter Registers and Receiver Registers sections; changed LEMC to LMFC.
2019.04.01	19.1	19.1	Added support for Intel® Stratix® 10 E-tile devices. Revised the resource utilization data for version 19.1 in the Performance and Resource Utilization section. Updated the JESD204B Intel® FPGA IP Performance table with Intel® Stratix® 10 E-tile device information in the Performance and Resource Utilization section. Updated the Channel Bonding section to include information about Intel® Stratix® 10 E-tile devices. For Intel® Stratix® 10 E-tile devices, you must use contiguous channels to enable channel bonding with NRZ PMA transceiver channels. Added the Transceiver Tile option which is available when you target an Intel® Stratix® 10 device that supports both and H-tile and E-tile. Renamed the Enable Altera Debug Master Endpoint parameter to Enable Native PHY Debug Master Endpoint as per Intel rebranding in the Intel® Quartus® Prime Pro Edition software. The Intel® Quartus® Prime Standard Edition software still uses Enable Altera Debug Master Endpoint. Added a note to refer to the PMA Adaptation section in the Intel Stratix 10 E-tile Transceiver PHY User Guide for more information about PMA Adaptation parameters. Edited the Transmitter Signals and Receiver Signals sections to add a note that certain signals are not applicable for Intel® Stratix® 10 E-tile devices or applicable only for Intel® Stratix® 10 L-tile and H-tile devices. Added the following signals that are applicable only for Intel® Stratix® 10 E-tile devices in the Transmitter Signals and Receiver Signals sections: phy_tx_ready phy_rx_ready phy_tx_pma_ready phy_rx_pma_ready phy_tx_rst_n phy_rx_rst_n tx_serial_data_n rx_serial_data_n Added a note in the Pin Assignments section to use the E-Tile Channel Placement Tool to get a valid pinout for Intel® Stratix® 10 E-tile devices. Added a note in the Adding External Transceiver PLLs section that Intel® Stratix® 10 E-tile device designs do not require external PLLs. Added a note in the Simulating the IP Core Testbench section that Intel® Stratix® 10 E-tile devices do not support the Riviera-PRO* simulator. Add information about Intel® Stratix® 10 E-tile devices in the Testbench Simulation Flow section. Edited the Creating a Debug File to Match Your Design Hierarchy section to add information about Intel® Stratix® 10 E-tile devices. Edited the Debugging JESD204B Link Using System Console section to add information about Intel® Stratix® 10 E-tile devices. Added the Transmitter Registers and Receiver Registers sections in the Registers chapter. The register information are now available in the document.
2018.12.10	18.1	18.1	Updated the Device Family Support section to indicate that the JESD204B Intel® FPGA IP core supports only Intel® Stratix® 10 (L-tile and H-tile) devices. Revised the data rate information for Intel® Stratix® 10 devices for speed grade 2 and 3. Revised the resource utilization data and speed grade information for version 18.1. Added resource utilization data and speed grade information for Intel® Stratix® 10 devices when number of octets per frame (F) is 3. Updated the Octets per frame (F) parameter option to support F=3 in the JESD204B IP Core Parameter section. F=3 is available only for Intel® Stratix® 10 devices. Categorized the following signals as debug and testing signals in the Transmitter Signals section: `csr_tx_testmode[3:0]` `csr_tx_testpattern_a[]` `csr_tx_testpattern_b[]` `csr_tx_testpattern_c[]` `csr_tx_testpattern_d[]` Categorized the `csr_rx_testmode[3:0]` signal as a debug and testing signal in the Receiver Signals section. Added a note in the Receiver Signals section that the test pattern checker is a component in the design example and is not a part of the JESD204B IP core Added a note in the Transmitter Signals section that the test pattern generator is a component in the design example and is not a part of the JESD204B IP core Edited the steps for running analysis and synthesis in the Creating a Signal Tap Debug File to Match Your Design section.
2018.05.07	18.0	18.0	Renamed JESD204B IP core to JESD204B Intel® FPGA IP as per Intel rebranding. Added support for Intel® Cyclone® 10 GX devices. Added simulation setup and run scripts for the Cadence Xcelium* Parallel simulator. Added links to the JESD204B Intel® FPGA IP Design Example for Intel® Cyclone® 10 GX Devices User Guide. Edited a typo in in the Brief Information About the JESD204B IP Core table. Changed Platform Designer (Standard) to Platform Designer. Revised the resource utilization data and speed grade information for version 18.0. Updated the JESD204B IP Core Parameters and Signals sections with Intel® Cyclone® 10 GX information. Edited the steps in the Creating a Signal Tap Debug File to Match Your Design Hierarchy section. Added a note in the Testbench Simulation Flow section that for Intel® Stratix® 10 devices, reset deassertion staggering of TX/RX analog and digital reset happens before the assertion of TX/RX ready.

Date	Version	Changes
November 2017	2017.11.06	Updated `alldev_lane_aligned` signal description. Updated bonded channel requirements for Intel® Stratix® 10 and Intel® Arria® 10 devices. Updated instances of Qsys to Platform Designer. Updated steps to simulate the testbench design using the Aldec Riviera-PRO simulator. Removed note stating that the dynamic reconfiguration is not supported for the JESD204B IP core testbench. Added Base only, or Simplex TX configuration in Preset Configurations for JESD204B IP Core Testbench table. Added Provide Separate Reconfiguration Interface for Each Channel parameter in the JESD204B IP Core Parameters table. Updated Link Clock F_MAX (MHz) for all devices in the JESD204B IP Core FPGA Performance table. Added supported data rate note to Intel® Arria® 10 variants in JESD204B IP Core FPGA Performance table. Updated rx_phy and tx_phy assignments in Creating a Signal Tap Debug File to Match Your Design Hierarchy. Updated the data rate support for Intel® Stratix® 10 devices: For speed grade 1 to up to 16.0 Gbps. For speed grade 2 to up to 13.5 Gbps. For speed grade 3 to up to 12.5 Gbps. Updated and added example timing diagrams in Subclass 2 Operating Mode subsection. Updated transceiver interface signals for transmitter and receiver signals.
May 2017	2017.05.08	Updated description for PLL/CDR Reference Clock Frequency in JESD204B IP Core Parameters. Added `somf[]` for transmitter signal. Updated Run-Time Configuration to include statement on JESD204B IP core parameterization for Intel® Stratix® 10 devices. Added note to Registers to indicate that disabled run-time access for registers in Intel® Stratix® 10 devices. Updated data path preset value to simplex TX and simplex RX in Preset Configurations for JESD204B IP Core Testbench table. Clarified the device family support for Stratix 10 devices. Added Transmitter and Receiver signal diagrams. Added Share Reconfiguration Interface parameter in JESD204B IP Core Parameters table. Added note and description to Share Reconfiguration Interface in JESD204B IP Core Parameters. Added links to Stratix 10 device Datasheet, Stratix 10 L-Tile Transceiver PHY User Guide, and Stratix 10 H-Tile Transceiver PHY User Guide. Added `tx_analogreset_stat`, `rx_analogreset_stat`, `tx_digitalreset_stat`, and `rx_digitalreset_stat` signals and descriptions. Updated ADC-FPGA Subsystem Reset Scheme and FPGA-DAC Subsystem Reset Scheme.
October 2016	2016.10.31	Updated Example 2 in Clock Correlation. Updated steps in FPGA–DAC Subsystem Reset Sequence. Updated figure and title for JESD204B Subsystem with Shared Transceiver Reference Clock and Core Clock and JESD204B Subsystem with Separate Transceiver Reference Clock and Core Clock. Updated Subclass 1 Deterministic Latency and Support for Programmable Release Opportunity figure. Updated Channel Bonding description.
May 2016	2016.05.02	Updated the IP Core release information. Updated the data rate support—uncharacterized support for data rates of up to 15 Gbps. Updated the data rate for Intel® Arria® 10 and Arria V GT/ST in the JESD204B IP Core FPGA Performance table. Updated the JESD204B IP Core FPGA Resource Utilization table. Updated the PLL/CDR Reference Clock Frequency parameter description. Updated the preset values for PLL/CDR Reference Clock Frequency, Link Clock, and AVS Clock in Table 3-8: Preset Configurations for JESD204B IP Core Testbench. Updated Figure 4-8 to illustrate shared clocking and renamed the title to "JESD204B Subsystem with Shared Transceiver Reference Clock and Core Clock". Added a new figure to illustrate separate clocking—Figure 4-9: JESD204B Subsystem with Separate Transceiver Reference Clock and Core Clock. Added new sections: ADC–FPGA Subsystem Reset Sequence FPGA–DAC Subsystem Reset Sequence Creating a Signal Tap Debug File to Match Your Design Hierarchy Updated the TX path CONTROL_BUS_ WIDTH parameter description. Revised the clock domain for `jesd204_tx_data_ready` signal to txframe_clk. Updated the description for the following registers in the register map: rx_regmap: `csr_frame_data_ready_err` `csr_pcfifo_full_err` `csr_pcfifo_empty_err` tx_regmap: `csr_pcfifo_full_err` `csr_pcfifo_empty_err` Added links to archived document in JESD204B Intel FPGA IP User Guide Archives.
November 2015	2015.11.02	Added data rate support of up to 13.5 Gbps for Intel® Arria® 10 and 7.5 Gbps for Arria V GT/ST devices. Updated the IP core FPGA performance and resource utilization values. Added a new table to define the clock network selection for bonded mode in channel bonding. Added a new selection for PCS Option parameter—Enabled PMA Direct. Updated the preset value for link clock in JESD204B IP Testbench. Updated the formula and description for TX/RX PHY clock. Updated the device clock section to recommend user to supply the device clock with the same frequency as the link clock. Updated the description of `txlink_clk`, `txphy_clk[]`, and `rxphy_clk[]` signals. Changed the default value for RX Phase Compensation FIFO empty error enable (`csr_pcfifo_empty_err_en`) CSR to 0. Refer to the RX register map for details. Added a new section—Design Example with Nios II Processor Control Unit. Added a new topic – Maintaining Deterministic Latency during Link Reinitialization. Changed instances of Quartus II to Quartus Prime.
May 2015	2015.05.04	Added support for Cyclone V FPGA device family. Updated the JESD204B IP Core Configuration values: M value from 1-32 to 1-256 N' value from 4-32 to 1-32 Updated the JESD204B IP Core FPGA Performance table. Updated the JESD204B IP Core FPGA Resource Utilization table. Added new parameters to the JESD204B IP Core Parameters table: Enable Capability Registers Set user-defined IP identifier Enable Control and Status Registers Enable Prbs Soft Accumulators Enable manual F configuration Added new topics: Timing Constraints For Input Clocks JESD204B IP Deterministic Latency Implementation Guidelines Revised the note in "Simulating the IP Core Testbench" to state that VHDL is not supported in Aldec Riviera (for Intel® Arria® 10 devices only). Updated the Control Unit Process Flow diagram.
December 2014	2014.12.15	Updated the JESD204B IP Core FPGA Performance table with the data rate range. Updated the JESD204B IP Core FPGA Resource Utilization table. Updated the JESD204B IP Core Parameters table with the following changes: Revised the parameter name of Enable PLL/CDR Dynamic Reconfiguration to Enable Transceiver Dynamic Reconfiguration. Added information for a new parameter—Enable Altera Debug Master Endpoint. Added details about the rule check for parameter N' value. Added a new topic—Integrating the JESD204B IP in Platform Designer. Updated Overview of the JESD204B IP Core Block Diagram, Transmitter Data Path Block Diagram, and Receiver Data Path Block Diagram. Added a new table—Register Access Type Convention—to describe the access type for the IP core registers. Added new signals description for `jesd204_tx_controlout` and `jesd204_rx_controlout`. Added CONTROL_BUS_WIDTH parameter and description for the assembler and deassembler. Added information on how to run the Tcl script using the Quartus II software before compiling the design example. Updated the section on Debugging JESD204B Link Using System Console with verification information for TX PHY-link layer interface, TX link layer, and TX transport layer operations.
June 2014	2014.06.30	Updated Figure 2-1 to show a typical system application. Updated the list of core key features. Updated the Performance and Resource utilization values. Updated the Getting Started chapter to reflect the new IP Catalog and parameter editor. Added the following new sections to further describe the JESD204B IP core features: Channel Bonding Datapath Modes IP Core Variation JESD204B IP Core Testbench JESD204B IP Core Design Considerations TX Data Link Layer TX PHY Layer RX Data Link Layer RX PHY Layer Operation Dynamic Reconfiguration JESD204B IP Core Debug Guidelines Updated the Clocking scheme section. Added new transceiver signals that is supported in Intel® Arria® 10 devices. Updated the Transport Layer section. Added run-time reconfiguration parameter values in the System Parameters section. Updated the file directory names.
November 2013	2013.11.04	Initial release.