Visible to Intel only — GUID: lbl1455130101432
Ixiasoft
1. Datasheet
2. Getting Started with the SR-IOV Design Example
3. Parameter Settings
4. Physical Layout
5. Interfaces and Signal Descriptions
6. Registers
7. Programming and Testing SR-IOV Bridge MSI Interrupts
8. Error Handling
9. IP Core Architecture
10. Design Implementation
11. Debugging
12. Document Revision History
A. Transaction Layer Packet (TLP) Header Formats
B. Intel® Arria® 10 Avalon-ST with SR-IOV Interface for PCIe Solutions User Guide Archive
3.1. Parameters
3.2. Intel® Arria® 10 Avalon-ST Settings
3.3. Intel® Arria® 10 SR-IOV System Settings
3.4. Base Address Register (BAR) Settings
3.5. SR-IOV Device Identification Registers
3.6. Intel® Arria® 10 Interrupt Capabilities
3.7. Physical Function TLP Processing Hints (TPH)
3.8. Address Translation Services (ATS)
3.9. PCI Express and PCI Capabilities Parameters
3.10. PHY Characteristics
3.11. Example Designs
4.1. Hard IP Block Placement In Intel® Cyclone® 10 GX Devices
4.2. Hard IP Block Placement In Intel® Arria® 10 Devices
4.3. Channel and Pin Placement for the Gen1, Gen2, and Gen3 Data Rates
4.4. Channel Placement and fPLL and ATX PLL Usage for the Gen3 Data Rate
4.5. PCI Express Gen3 Bank Usage Restrictions
5.1. Avalon-ST TX Interface
5.2. Component-Specific Avalon-ST Interface Signals
5.3. Avalon-ST RX Interface
5.4. BAR Hit Signals
5.5. Configuration Status Interface
5.6. Clock Signals
5.7. Function-Level Reset (FLR) Interface
5.8. SR-IOV Interrupt Interface
5.9. Configuration Extension Bus (CEB) Interface
5.10. Implementing MSI-X Interrupts
5.11. Control Shadow Interface
5.12. Local Management Interface (LMI) Signals
5.13. Reset, Status, and Link Training Signals
5.14. Hard IP Reconfiguration Interface
5.15. Serial Data Signals
5.16. Test Signals
5.17. PIPE Interface Signals
5.18. Intel® Arria® 10 Development Kit Conduit Interface
6.1. Addresses for Physical and Virtual Functions
6.2. Correspondence between Configuration Space Registers and the PCIe Specification
6.3. PCI and PCI Express Configuration Space Registers
6.4. MSI Registers
6.5. MSI-X Capability Structure
6.6. Power Management Capability Structure
6.7. PCI Express Capability Structure
6.8. Advanced Error Reporting (AER) Enhanced Capability Header Register
6.9. Uncorrectable Error Status Register
6.10. Uncorrectable Error Mask Register
6.11. Uncorrectable Error Severity Register
6.12. Correctable Error Status Register
6.13. Correctable Error Mask Register
6.14. Advanced Error Capabilities and Control Register
6.15. Header Log Registers 0-3
6.16. SR-IOV Virtualization Extended Capabilities Registers
6.17. Virtual Function Registers
6.16.1. SR-IOV Virtualization Extended Capabilities Registers Address Map
6.16.2. ARI Enhanced Capability Header
6.16.3. SR-IOV Enhanced Capability Registers
6.16.4. Initial VFs and Total VFs Registers
6.16.5. VF Device ID Register
6.16.6. Page Size Registers
6.16.7. VF Base Address Registers (BARs) 0-5
6.16.8. Secondary PCI Express Extended Capability Header
6.16.9. Lane Status Registers
6.16.10. Transaction Processing Hints (TPH) Requester Enhanced Capability Header
11.1.1. Changing Between Serial and PIPE Simulation
11.1.2. Using the PIPE Interface for Gen1 and Gen2 Variants
11.1.3. Viewing the Important PIPE Interface Signals
11.1.4. Disabling the Scrambler for Gen1 and Gen2 Simulations
11.1.5. Disabling 8B/10B Encoding and Decoding for Gen1 and Gen2 Simulations
Visible to Intel only — GUID: lbl1455130101432
Ixiasoft
11.5. Creating a Signal Tap Debug File to Match Your Design Hierarchy
For Intel® Arria® 10 and Intel® Cyclone® 10 GX devices, the Intel® Quartus® Prime software generates two files, build_stp.tcl and <ip_core_name>.xml. You can use these files to generate a Signal Tap file with probe points matching your design hierarchy.
The Intel® Quartus® Prime software stores these files in the <IP core directory>/synth/debug/stp/ directory.
Synthesize your design using the Intel® Quartus® Prime software.
- To open the Tcl console, click View > Utility Windows > Tcl Console.
- Type the following command in the Tcl console:
source <IP core directory>/synth/debug/stp/build_stp.tcl
- To generate the STP file, type the following command:
main -stp_file <output stp file name>.stp -xml_file <input xml_file name>.xml -mode build
- To add this Signal Tap file (.stp) to your project, select Project > Add/Remove Files in Project. Then, compile your design.
- To program the FPGA, click Tools > Programmer.
- To start the Signal Tap Logic Analyzer, click Quartus Prime > Tools > Signal Tap Logic Analyzer.
The software generation script may not assign the Signal Tap acquisition clock in <output stp file name>.stp. Consequently, the Intel® Quartus® Prime software automatically creates a clock pin called auto_stp_external_clock. You may need to manually substitute the appropriate clock signal as the Signal Tap sampling clock for each STP instance.
- Recompile your design.
- To observe the state of your IP core, click Run Analysis.
You may see signals or Signal Tap instances that are red, indicating they are not available in your design. In most cases, you can safely ignore these signals and instances. They are present because software generates wider buses and some instances that your design does not include.