JESD204B Intel® FPGA IP Design Example User Guide: Intel® Quartus® Prime Standard Edition

Download PDF
ID 683094
Date 10/31/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. JESD204B Intel® FPGA IP Design Example User Guide
1. JESD204B Intel® FPGA IP Design Example User Guide x
1.1. JESD204B Design Example Quick Start Guide 1.2. Supported Configurations 1.3. Generic Design Example 1.4. Presets 1.5. Selecting and Generating the Design Example 1.6. Design Example with RTL State Machine Control Unit 1.7. Design Example with NIOS Control Unit 1.8. JESD204B Intel® FPGA IP Design Example User Guide Document Archives 1.9. Document Revision History for the JESD204B Intel® FPGA IP Design Example User Guide
1.1. JESD204B Design Example Quick Start Guide x
1.1.1. Directory Structure 1.1.2. Generating the Design 1.1.3. Compiling and Simulating the Design 1.1.4. Compiling and Testing the Design
1.1.2. Generating the Design x
1.1.2.1. Procedure 1.1.2.2. Design Example Parameters
1.1.3. Compiling and Simulating the Design x
1.1.3.1. Procedure
1.6. Design Example with RTL State Machine Control Unit x
1.6.1. Design Example Components 1.6.2. System Parameters 1.6.3. System Interface Signals 1.6.4. Example Feature: Dynamic Reconfiguration 1.6.5. Generating and Simulating the Design Example 1.6.6. Generating the Design Example For Compilation 1.6.7. Compiling the JESD204B IP Core Design Example
1.6.1. Design Example Components x
1.6.1.1. PLL 1.6.1.2. PLL Reconfiguration 1.6.1.3. Transceiver Reconfiguration Controller 1.6.1.4. Transceiver Reset Controller 1.6.1.5. Pattern Generator 1.6.1.6. Pattern Checker 1.6.1.7. Transport Layer 1.6.1.8. Serial Port Interface (SPI) 1.6.1.9. Control Unit
1.6.1.5. Pattern Generator x
1.6.1.5.1. Parallel PRBS Generator 1.6.1.5.2. Alternate Checkerboard Generator 1.6.1.5.3. Ramp Wave Generator
1.6.1.6. Pattern Checker x
1.6.1.6.1. Parallel PRBS Checker 1.6.1.6.2. Alternate Checkerboard Checker 1.6.1.6.3. Ramp Wave Checker
1.6.1.7. Transport Layer x
1.6.1.7.1. Supported System Configuration 1.6.1.7.2. Data Bit and Content Mapping Scheme 1.6.1.7.3. TX Path 1.6.1.7.4. RX Path
1.6.1.9. Control Unit x
1.6.1.9.1. Memory Block (ROM) 1.6.1.9.2. Finite State Machine (FSM)
1.6.2. System Parameters x
1.6.2.1. Run-Time Reconfiguration
1.6.4. Example Feature: Dynamic Reconfiguration x
1.6.4.1. Dynamic Reconfiguration Operation 1.6.4.2. MIF ROM
1.6.5. Generating and Simulating the Design Example x
1.6.5.1. Generating the Design Example Simulation Model 1.6.5.2. Simulating the JESD204B IP Core Design Example
1.7. Design Example with NIOS Control Unit x
1.7.1. Design Example Components 1.7.2. System Clocking 1.7.3. Nios II Processor Design Example Files 1.7.4. Nios II Processor Design Example System Parameters 1.7.5. Nios II Processor Design Example System Interface Signals 1.7.6. Compiling the Design Example for Synthesis 1.7.7. Implementing the Design on the Development Kit 1.7.8. Running the Software Control Flow 1.7.9. Customizing the Design Example
1.7.1. Design Example Components x
1.7.1.1. Platform Designer (Standard) System Component 1.7.1.2. Transport Layer 1.7.1.3. Test Pattern Generator 1.7.1.4. Test Pattern Checker
1.7.1.1. Platform Designer (Standard) System Component x
1.7.1.1.1. JESD204B Subsystem in Platform Designer (Standard) 1.7.1.1.2. Nios II Subsystem in Platform Designer (Standard) 1.7.1.1.3. Core PLL 1.7.1.1.4. PLL Reconfiguration Controller 1.7.1.1.5. SPI Master
1.7.7. Implementing the Design on the Development Kit x
1.7.7.1. Pin Assignments 1.7.7.2. Hardware Setup 1.7.7.3. Programming the Device
1.7.8. Running the Software Control Flow x
1.7.8.1. Executing the Software C Code 1.7.8.2. Software Parameters 1.7.8.3. Software Interrupt Service Routines (ISR) 1.7.8.4. Software Functions Description
1.7.8.4. Software Functions Description x
1.7.8.4.1. Functions in main.c Source File 1.7.8.4.2. Custom Peripheral Access Macros in macros.c Source File
1.7.9. Customizing the Design Example x
1.7.9.1. Modifying the JESD204B IP Core Parameters Post-Generation 1.7.9.2. Changing the Data Rate or Reference Clock Frequency 1.7.9.3. Implementing a Multi-Link Design
1.7.9.3. Implementing a Multi-Link Design x
1.7.9.3.1. Editing the Platform Designer (Standard) Project 1.7.9.3.2. Editing the Top Level HDL File 1.7.9.3.3. Editing the Software C Code
1. JESD204B Intel® FPGA IP Design Example User Guide

1.7.7.3. Programming the Device

Follow the steps below to setup and program the device on the development board.

  1. Connect the mini-USB programming cable from your workstation to the mini-USB connector (J3) on the development board.
  2. Connect the power adapter shipped with the development board to the power supply jack (J13).
  3. Turn on the power for the development board.
  4. To configure the clock frequency for the mgmt_clk that is sourced from the on-board Si570 programmable oscillator (X3), use the Altera Clock Control GUI that is included with the development kit. Select the Si570 (X3) tab, enter the required target frequency in the Target frequency (MHz) box and click Set New Frequency. The correct target frequency value is 100 MHz.
    You must set the CLK_SEL port of the Si53301 clock buffer module (U42) on the board to LOW to select the Si570 clock output. To set the CLK_SEL signal to LOW, set switch 1 of DIPSWITCH5 (SW6) to the ON position. Refer to the Arria 10 GX FPGA development kit schematic and related documentation for more details.
  5. To configure the clock frequency for the device_clk that is sourced from the on-board Si5338 programmable oscillator, use the Altera Clock Control GUI that is included with the development kit. Select the Si5338 (U14) tab, enter the required target frequency in the CLK1 box and click Set New Freq. The correct target frequency value depends on the L parameter selected for the example design. The table below lists the required values for the device_clk, with the serial data rate set as 6.144 Gbps.
    L Parameter Target Frequency (MHz)
    8 307.2
    Others 153.6
  6. Compile the design as described in the Compiling Example Design For Synthesis section.
  7. In the Tools menu, click Programmer.
  8. In the Programmer window, click Add File.
  9. In the Select Programming File window, navigate to <your project> /ed_nios/output_files and select the SOF programming file (jesd204b_ed.sof). Click Open.
  10. Verify that all the hardware setup options are set correctly to your system configurations.
  11. Click Start to program the file into the board device.
After programming the Arria 10 FPGA device on the development board, the system needs to be initialized via software before the link is fully active. Follow the steps in the Executing the Software C Code section to complete the link initialization process.
Attention: Do not skip this step. The JESD204B link does not function correctly without software link initialization.
Related Information
Level Two Title