E-tile Hard IP User Guide: E-Tile Hard IP for Ethernet and E-Tile CPRI PHY Intel® FPGA IPs

ID 683468
Date 8/30/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

2.8.2. RTL Parameters

The E-Tile Hard IP for Ethernet Intel FPGA IP provides parameters in the generated RTL that you can modify for your IP core instance. Generating an IP core variation from the parameter editor creates an RTL module. Your design might instantiate multiple instances of this module. You can specify RTL parameter values for each instance. Each RTL parameter determines the initial and reset value of one or more register fields in the IP core.

RTL parameters allow you to customize your IP core instance to vary from the defaults you selected for your IP core variation and from other instances of the same IP core variation. This capability allows you to fine-tune your design without regenerating and without reading and writing registers following power-up. In addition, you can specify parameter values that should not be identical for multiple instances. For example, you can specify a different TX source address for each instance, without having to write to the relevant registers.

To access the RTL parameters, refer to the IP configuration and test files. The simulation-based RTL parameters are located in <your_project_directory>\<your_IP_name>\sim\<your_IP_name>.v The synthesis-based RTL parameters are located in <your_project_directory>\<your_IP_name>\synth\<your_IP_name>.v.

Table 19.   E-Tile Hard IP for Ethernet Intel FPGA IP RTL Parameters

Parameter

Parameter Description

Parameters Available for all IP Core Variations
sim_mode Specifies whether the IP core is in simulation mode, in which alignment marker periods are shortened to decrease the time to RX PCS alignment.
  • Value disable (default value): The IP core MAC implements standard alignment marker periods as specified in the IEEE Standard 802.3–2015. Before compiling for synthesis, ensure this parameter has this value.
  • Value enable: The IP core implements shorter alignment marker periods to accelerate RX PCS alignment in simulation. The simulation link partner must have the same alignment marker periods. This mode is intended for simulation only.

The value of this parameter determines the initial and reset values of these register fields:

  • am_interval[13:0] field (bits [13:0]) of the RXPCS_CONF register at 0ffset 0x360.
  • am_period[15:0] field (bits [31:16]) of the TXMAC_EHIP_CFG register at 0ffset 0x40B.
Parameters Available for MAC+PCS IP Core Variations Only
rx_pause_daddr Sets the destination addresses for PAUSE and PFC frames. The RX MAC uses this address to filter whether incoming PAUSE and PFC frames apply to the current IP core.
  • Default value is 0x0F_2C_B8_35_37_15, the Ethernet standard multicast address for PAUSE and PFC.
  • Range is 0 through 248–1.
  • Value can be a unicast or multicast address.
  • The RX MAC processes PAUSE and PFC frames only if their destination address matches this address (actually, the address in the RX_PAUSE_DADDR registers).

The value of this parameter determines the initial and reset values of the RX_PAUSE_DADDR registers at offsets 0x707 and 0x708.

source_address_insertion Selects whether the IP core supports overwriting the source address in an outgoing packet it receives on the TX MAC interface, with the value in the TXMAC_SADDR registers at offsets 0x40C and 0x40D.
  • The default value is the value of the parameter editor Use Source Address Insertion parameter.
  • Value enable: If i_tx_skip_crc has the value of 0, in packets the IP core receives on the TX MAC client interface, the TX MAC overwrites the source address field with the value in the TXMAC_SADDR registers at offsets 0x40C and 0x40D.
    Note: The IP core does not overwrite the source address in Ethernet PAUSE and PFC packets it generates on the Ethernet link in response to assertion of the i_tx_pause signal or an i_tx_pfc[n] signal on the TX MAC client interface.
  • Value disable: The TX MAC does not overwrite the source address field in packets it receives on the TX MAC client interface.

The value of this parameter determines the initial and reset values of the en_saddr_insert field (bit [3]) of the TXMAC_CONTROL register at 0ffset 0x40A.

tx_pause_daddr Sets the destination addresses that the TX MAC inserts in PAUSE and PFC frames that the IP core transmits on the Ethernet link in response to assertion of the i_tx_pause signal or an i_tx_pfc[n] signal on the TX MAC client interface.
  • Default value is 0x01_80_C2_00_00_01, the Ethernet standard multicast address for PAUSE and PFC.
  • Range is 0 through 248–1.
  • Value can be a unicast or multicast address.

The value of this parameter determines the initial and reset values of the TX_PFC_DADDR registers at offsets 0x60D and 0x60E.

tx_pause_saddr Sets the source addresses that the TX MAC inserts in PAUSE and PFC frames that the IP core transmits on the Ethernet link in response to assertion of the i_tx_pause signal or an i_tx_pfc[n] signal on the TX MAC client interface.
  • Default value is the value of the RTL parameter txmac_saddr, which is the initial source address the IP core inserts in all TX packets written to the TX MAC client interface when source MAC address insertion is enabled.
  • Range is 0 through 248–1.
  • Value should be a unicast address.

The value of this parameter determines the initial and reset values of the TX_PFC_SADDR registers at offsets 0x60F and 0x610.

txmac_saddr Sets the source addresses that the TX MAC inserts in packets written to the TX MAC client interface when source MAC address insertion is enabled.
  • Default value is the value you specify for the parameter editor TX MAC Source Address parameter.
  • Range is 0 through 248–1.
  • The Intel® FPGA team recommends you program each IP core instance with a unique unicast MAC address.

The value of this parameter determines the initial and reset values of the TXMAC_SADDR registers at offsets 0x40C and 0x40D.