3.4.2.1. The status Register
3.4.2.2. The estatus Register
3.4.2.3. The bstatus Register
3.4.2.4. The ienable Register
3.4.2.5. The ipending Register
3.4.2.6. The cpuid Register
3.4.2.7. The exception Register
3.4.2.8. The pteaddr Register
3.4.2.9. The tlbacc Register
3.4.2.10. The tlbmisc Register
3.4.2.11. The badaddr Register
3.4.2.12. The config Register
3.4.2.13. The mpubase Register
3.4.2.14. The mpuacc Register
3.7.1. Terminology
3.7.2. Exception Overview
3.7.3. Exception Latency
3.7.4. Reset Exceptions
3.7.5. Break Exceptions
3.7.6. Interrupt Exceptions
3.7.7. Instruction-Related Exceptions
3.7.8. Other Exceptions
3.7.9. Exception Processing Flow
3.7.10. Handling Nested Exceptions
3.7.11. Handling Nonmaskable Interrupts
3.7.12. Masking and Disabling Exceptions
3.7.7.1. Trap Instruction
3.7.7.2. Break Instruction
3.7.7.3. Unimplemented Instruction
3.7.7.4. Illegal Instruction
3.7.7.5. Supervisor-Only Instruction
3.7.7.6. Supervisor-Only Instruction Address
3.7.7.7. Supervisor-Only Data Address
3.7.7.8. Misaligned Data Address
3.7.7.9. Misaligned Destination Address
3.7.7.10. Division Error
3.7.7.11. Fast TLB Miss
3.7.7.12. Double TLB Miss
3.7.7.13. TLB Permission Violation
3.7.7.14. MPU Region Violation
3.9.1. Data Transfer Instructions
3.9.2. Arithmetic and Logical Instructions
3.9.3. Move Instructions
3.9.4. Comparison Instructions
3.9.5. Shift and Rotate Instructions
3.9.6. Program Control Instructions
3.9.7. Other Control Instructions
3.9.8. Custom Instructions
3.9.9. No-Operation Instruction
3.9.10. Potential Unimplemented Instructions
8.5.1. add
8.5.2. addi
8.5.3. and
8.5.4. andhi
8.5.5. andi
8.5.6. beq
8.5.7. bge
8.5.8. bgeu
8.5.9. bgt
8.5.10. bgtu
8.5.11. ble
8.5.12. bleu
8.5.13. blt
8.5.14. bltu
8.5.15. bne
8.5.16. br
8.5.17. break
8.5.18. bret
8.5.19. call
8.5.20. callr
8.5.21. cmpeq
8.5.22. cmpeqi
8.5.23. cmpge
8.5.24. cmpgei
8.5.25. cmpgeu
8.5.26. cmpgeui
8.5.27. cmpgt
8.5.28. cmpgti
8.5.29. cmpgtu
8.5.30. cmpgtui
8.5.31. cmple
8.5.32. cmplei
8.5.33. cmpleu
8.5.34. cmpleui
8.5.35. cmplt
8.5.36. cmplti
8.5.37. cmpltu
8.5.38. cmpltui
8.5.39. cmpne
8.5.40. cmpnei
8.5.41. custom
8.5.42. div
8.5.43. divu
8.5.44. eret
8.5.45. flushd
8.5.46. flushda
8.5.47. flushi
8.5.48. flushp
8.5.49. initd
8.5.50. initda
8.5.51. initi
8.5.52. jmp
8.5.53. jmpi
8.5.54. ldb / ldbio
8.5.55. ldbu / ldbuio
8.5.56. ldh / ldhio
8.5.57. ldhu / ldhuio
8.5.58. ldw / ldwio
8.5.59. mov
8.5.60. movhi
8.5.61. movi
8.5.62. movia
8.5.63. movui
8.5.64. mul
8.5.65. muli
8.5.66. mulxss
8.5.67. mulxsu
8.5.68. mulxuu
8.5.69. nextpc
8.5.70. nop
8.5.71. nor
8.5.72. or
8.5.73. orhi
8.5.74. ori
8.5.75. rdctl
8.5.76. rdprs
8.5.77. ret
8.5.78. rol
8.5.79. roli
8.5.80. ror
8.5.81. sll
8.5.82. slli
8.5.83. sra
8.5.84. srai
8.5.85. srl
8.5.86. srli
8.5.87. stb / stbio l
8.5.88. sth / sthio
8.5.89. stw / stwio
8.5.90. sub
8.5.91. subi
8.5.92. sync
8.5.93. trap
8.5.94. wrctl
8.5.95. wrprs
8.5.96. xor
8.5.97. xorhi
8.5.98. xori
2.5.3. Internal Interrupt Controller
The Nios II architecture supports 32 internal hardware interrupts. The processor core has 32 level-sensitive interrupt request (IRQ) inputs, irq0 through irq31, providing a unique input for each interrupt source. IRQ priority is determined by software. The architecture supports nested interrupts.
Your software can enable and disable any interrupt source individually through the ienable control register, which contains an interrupt-enable bit for each of the IRQ inputs. Software can enable and disable interrupts globally using the PIE bit of the status control register. A hardware interrupt is generated if and only if all of the following conditions are true:
- The PIE bit of the status register is 1
- An interrupt-request input, irq<n>, is asserted
- The corresponding bit n of the ienable register is 1
The interrupt vector custom instruction is less efficient than using the EIC interface with the Intel FPGA vectored interrupt controller component, and thus is deprecated in Platform Designer. Intel recommends using the EIC interface.