Visible to Intel only — GUID: itx1708723794110
Ixiasoft
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP
4. Implementing the GTS System PLL Clocks Intel FPGA IP
5. Implementing the GTS Reset Sequencer Intel FPGA IP
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide
3.1. IP Overview
3.2. Designing with the GTS PMA/FEC Direct PHY Intel FPGA IP
3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP
3.4. Signal and Port Reference
3.5. Bit Mapping for PMA and FEC Mode PHY TX and RX Datapath
3.6. Clocking
3.7. Custom Cadence Generation Ports and Logic
3.8. Asserting reset
3.9. Bonding Implementation
3.10. Configuration Register
3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing
3.12. Configurable Quartus® Prime Software Settings
3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.4.1. TX and RX Parallel and Serial Interface Signals
3.4.2. TX and RX Reference Clock and Clock Output Interface Signals
3.4.3. Reset Signals
3.4.4. FEC Signals
3.4.5. Custom Cadence Control and Status Signals
3.4.6. RX PMA Status Signals
3.4.7. TX and RX PMA and Core Interface FIFO Signals
3.4.8. Avalon Memory Mapped Interface Signals
3.8.1. Reset Signal Requirements
3.8.2. Power On Reset Requirements
3.8.3. Reset Signals—Block Level
3.8.4. Run-time Reset Sequence—TX
3.8.5. Run-time Reset Sequence—RX
3.8.6. Run-time Reset Sequence—TX + RX
3.8.7. Run-time Reset Sequence—TX with FEC
3.8.8. RX Data Loss/CDR Lock Loss (Auto-Recovery)
3.8.9. TX PLL Lock Loss
6.1. Instantiating the GTS PMA/FEC Direct PHY Intel FPGA IP
6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.3. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description
6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench
6.5. Compiling the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
Visible to Intel only — GUID: itx1708723794110
Ixiasoft
8.3.3. Loading the Design to the Transceiver Toolkit
To launch the toolkit, click Tools ➤ System Debugging Tools ➤ System Debugging Toolkits.
If the FPGA is already programmed with the project when loading, the transceiver toolkit automatically links the design to the target hardware in the toolkit. The toolkit automatically discovers links between the transmitter and receiver of the same channel. Before loading the design, ensure that you connect the hardware with the Intel FPGA. The device and JTAG connections appear in the devices and connections folders of the System Explorer pane as shown in the following figure.
Figure 87. System Explorer Pane
To load the design into the transceiver toolkit, follow these steps:
- In System Console, click File ➤ Load Design.
- Select the .sof programming file for the transceiver design.
After loading the project, the designs and design_instances folders in the System Explorer pane display information about the design, such as the design name and the blocks in the design that can communicate to the System Console.