Visible to Intel only — GUID: umd1681414633790
Ixiasoft
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP
4. Implementing the GTS System PLL Clocks Intel FPGA IP
5. Implementing the GTS Reset Sequencer Intel FPGA IP
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide
3.1. IP Overview
3.2. Designing with the GTS PMA/FEC Direct PHY Intel FPGA IP
3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP
3.4. Signal and Port Reference
3.5. Bit Mapping for PMA and FEC Mode PHY TX and RX Datapath
3.6. Clocking
3.7. Custom Cadence Generation Ports and Logic
3.8. Asserting reset
3.9. Bonding Implementation
3.10. Configuration Register
3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing
3.12. Configurable Quartus® Prime Software Settings
3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.4.1. TX and RX Parallel and Serial Interface Signals
3.4.2. TX and RX Reference Clock and Clock Output Interface Signals
3.4.3. Reset Signals
3.4.4. FEC Signals
3.4.5. Custom Cadence Control and Status Signals
3.4.6. RX PMA Status Signals
3.4.7. TX and RX PMA and Core Interface FIFO Signals
3.4.8. Avalon Memory Mapped Interface Signals
3.8.1. Reset Signal Requirements
3.8.2. Power On Reset Requirements
3.8.3. Reset Signals—Block Level
3.8.4. Run-time Reset Sequence—TX
3.8.5. Run-time Reset Sequence—RX
3.8.6. Run-time Reset Sequence—TX + RX
3.8.7. Run-time Reset Sequence—TX with FEC
3.8.8. RX Data Loss/CDR Lock Loss (Auto-Recovery)
3.8.9. TX PLL Lock Loss
6.1. Instantiating the GTS PMA/FEC Direct PHY Intel FPGA IP
6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.3. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description
6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench
6.5. Compiling the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
Visible to Intel only — GUID: umd1681414633790
Ixiasoft
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
This chapter describes the Example Design generation in the GTS PMA/FEC Direct PHY Intel FPGA IP. There are a few example designs supported currently and these example designs show the various connections between the IPs and their configuration. The following IPs from the Quartus® Prime Pro Edition software IP catalog are used in all the example designs:
- GTS PMA/FEC Direct PHY Intel FPGA IP
- GTS System PLL Clocks Intel FPGA IP
- GTS Reset Sequencer Intel FPGA IP
The example design also provides a simulation testbench that supports compilation and simulation. When you generate the example design, the parameter editor automatically creates the files necessary to simulate the design. You can use the supported simulator to run the testbench to observe the GTS PMA/FEC Direct PHY Intel FPGA IP functional simulation results and behavior.
Section Content
Instantiating the GTS PMA/FEC Direct PHY Intel FPGA IP
Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description
Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench
Compiling the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design