PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

Download PDF
ID 683716
Date 7/15/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the PHY Lite for Parallel Interfaces IP 2. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices 3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices 4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices 5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices 6. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Devices 7. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives 8. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide
1. About the PHY Lite for Parallel Interfaces IP x
1.1. Device Family Support 1.2. Features
2. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices x
2.1. Release Information 2.2. Functional Description 2.3. Getting Started 2.4. I/O Standards 2.5. Design Example
2.2. Functional Description x
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices Top Level Interfaces 2.2.2. Dynamic Reconfiguration
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices Top Level Interfaces x
2.2.1.1. Clocks 2.2.1.2. Output Path 2.2.1.3. Input Path
2.2.2. Dynamic Reconfiguration x
2.2.2.1. Calibration IP 2.2.2.2. Dynamic Reconfigurable Delays 2.2.2.3. Register Map
2.3. Getting Started x
2.3.1. Parameter Settings 2.3.2. Signals
2.3.2. Signals x
2.3.2.1. Clock and Reset Interface Signals 2.3.2.2. Output Path Signals 2.3.2.3. Input Path Signals
2.4. I/O Standards x
2.4.1. Design Guidelines
2.4.1. Design Guidelines x
2.4.1.1. DQS Trees 2.4.1.2. Pin Placement Restrictions 2.4.1.3. Maximum Number of DQ Data Pin Configurations
2.4.1.3. Maximum Number of DQ Data Pin Configurations x
2.4.1.3.1. Automatic and Manual Pin Placement 2.4.1.3.2. Single-Ended Pin Configurations 2.4.1.3.3. Differential Pin Configurations 2.4.1.3.4. Mixed Pin Configurations
2.5. Design Example x
2.5.1. Generate the Design Example 2.5.2. Verify Simulation Design Examples using Tester IP
2.5.1. Generate the Design Example x
2.5.1.1. Design Example without Dynamic Reconfiguration 2.5.1.2. Design Example with Dynamic Reconfiguration
2.5.1.1. Design Example without Dynamic Reconfiguration x
2.5.1.1.1. Generate the Synthesis Design Example without Dynamic Reconfiguration 2.5.1.1.2. Generate the Simulation Design Example Without Dynamic Reconfiguration 2.5.1.1.3. Run the Simulation Design Example Without Dynamic Reconfiguration
2.5.1.2. Design Example with Dynamic Reconfiguration x
2.5.1.2.1. Generate the Synthesis Design Example With Dynamic Reconfiguration 2.5.1.2.2. Generate the Simulation Design Example with Dynamic Reconfiguration 2.5.1.2.3. Run the Simulation Design Example Without Dynamic Reconfiguration
2.5.2. Verify Simulation Design Examples using Tester IP x
2.5.2.1. PHY Lite Interface 2.5.2.2. I/O Model 2.5.2.3. IOSSM Tester 2.5.2.4. Write Test 2.5.2.5. Read Test 2.5.2.6. Calbus Test
3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices x
3.1. Release Information 3.2. Functional Description 3.3. Getting Started 3.4. I/O Standards 3.5. Design Example
3.2. Functional Description x
3.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices Top Level Interfaces 3.2.2. Dynamic Reconfiguration 3.2.3. I/O Timing
3.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices Top Level Interfaces x
3.2.1.1. Clocks 3.2.1.2. Output Path 3.2.1.3. Input Path
3.2.1.1. Clocks x
3.2.1.1.1. Clock Frequency Relationships
3.2.2. Dynamic Reconfiguration x
3.2.2.1. Calibration IP 3.2.2.2. Dynamic Reconfigurable Delays 3.2.2.3. Register Map
3.3. Getting Started x
3.3.1. Parameter Settings 3.3.2. Signals
3.3.2. Signals x
3.3.2.1. Clock and Reset Interface Signals 3.3.2.2. Output Path Signals 3.3.2.3. Input Path Signals
3.4. I/O Standards x
3.4.1. Design Guidelines
3.4.1. Design Guidelines x
3.4.1.1. DQS Trees 3.4.1.2. Pin Placement Restrictions
3.5. Design Example x
3.5.1. Generating the Design Example 3.5.2. Verifying Simulation Design Examples using Tester IP
3.5.1. Generating the Design Example x
3.5.1.1. Design Example without Dynamic Reconfiguration 3.5.1.2. Dynamic Reconfiguration Design Examples
3.5.1.1. Design Example without Dynamic Reconfiguration x
3.5.1.1.1. Generating the Synthesis Design Example 3.5.1.1.2. Generating the Simulation Design Example
3.5.1.2. Dynamic Reconfiguration Design Examples x
3.5.1.2.1. Generating the Synthesis Design Example 3.5.1.2.2. Generating the Simulation Design Example
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices x
4.1. Release Information 4.2. Functional Description 4.3. Getting Started 4.4. I/O Standards 4.5. Design Guidelines 4.6. Design Example
4.2. Functional Description x
4.2.1. Agilex™ 7 F-Series and I-Series I/O Sub-bank Interconnects 4.2.2. Agilex™ 7 F-Series and I-Series Input DQS/Strobe Tree 4.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices Top Level Interfaces 4.2.4. Dynamic Reconfiguration 4.2.5. I/O Timing
4.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices Top Level Interfaces x
4.2.3.1. Clocks 4.2.3.2. Output Path 4.2.3.3. Input Path
4.2.3.1. Clocks x
4.2.3.1.1. Clock Frequency Relationships
4.2.4. Dynamic Reconfiguration x
4.2.4.1. Connectivity 4.2.4.2. Reconfiguration Features and Register Addressing 4.2.4.3. Dynamic Reconfiguration Guidelines
4.2.4.2. Reconfiguration Features and Register Addressing x
4.2.4.2.1. Control Registers Addresses 4.2.4.2.2. Control Registers
4.2.4.3. Dynamic Reconfiguration Guidelines x
4.2.4.3.1. Strobe Enable Window Calibration 4.2.4.3.2. Output and Strobe Enable Minimum and Maximum Phase Settings 4.2.4.3.3. Input DQ/DQS Delay Chains Maximum Values
4.3. Getting Started x
4.3.1. Parameter Settings 4.3.2. Signals
4.3.1. Parameter Settings x
4.3.1.1. Read Latency 4.3.1.2. Write Latency
4.3.2. Signals x
4.3.2.1. Clock and Reset Interface Signals 4.3.2.2. Output Path Signals 4.3.2.3. Input Path Signals
4.4. I/O Standards x
4.4.1. Input Buffer Reference Voltage (VREF) 4.4.2. On-Chip Termination (OCT)
4.4.2. On-Chip Termination (OCT) x
4.4.2.1. RZQ_GROUP Assignment
4.5. Design Guidelines x
4.5.1. Guidelines: Group Pin Placement 4.5.2. Reference Clock 4.5.3. Reset
4.6. Design Example x
4.6.1. Generating the Design Example
4.6.1. Generating the Design Example x
4.6.1.1. Design Example without Dynamic Reconfiguration 4.6.1.2. Dynamic Reconfiguration Design Examples
4.6.1.1. Design Example without Dynamic Reconfiguration x
4.6.1.1.1. Generating the Synthesis Design Example 4.6.1.1.2. Generating the Simulation Design Example
4.6.1.2. Dynamic Reconfiguration Design Examples x
4.6.1.2.1. Generating the Synthesis Design Example 4.6.1.2.2. Generating the Simulation Design Example
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices x
5.1. Release Information 5.2. Functional Description 5.3. Getting Started 5.4. I/O Standards 5.5. Design Guidelines 5.6. Design Example
5.2. Functional Description x
5.2.1. Top Level Interfaces 5.2.2. Clocks 5.2.3. Output Path 5.2.4. Input Path 5.2.5. Dynamic Reconfiguration
5.2.2. Clocks x
5.2.2.1. Clock Frequency Relationships
5.2.3. Output Path x
5.2.3.1. Output Path Data Alignment
5.2.4. Input Path x
5.2.4.1. Input Path Data Alignment
5.2.5. Dynamic Reconfiguration x
5.2.5.1. RTL Connectivity 5.2.5.2. Address Lookup 5.2.5.3. Reconfiguration Features and Register Addressing 5.2.5.4. Calibration Guidelines
5.2.5.1. RTL Connectivity x
5.2.5.1.1. Daisy Chain
5.2.5.2. Address Lookup x
5.2.5.2.1. Strobes 5.2.5.2.2. Parameter Table Examples
5.2.5.3. Reconfiguration Features and Register Addressing x
5.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices Control Registers Addresses 5.2.5.3.2. Control Registers Description
5.2.5.4. Calibration Guidelines x
5.2.5.4.1. Strobe Enable Window Calibration 5.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
5.3. Getting Started x
5.3.1. Parameter Settings 5.3.2. Signals
5.3.1. Parameter Settings x
5.3.1.1. Read Latency 5.3.1.2. Write Latency
5.3.2. Signals x
5.3.2.1. Clock and Reset Interface Signals 5.3.2.2. Output Path Signals 5.3.2.3. Input Path Signals 5.3.2.4. Avalon Configuration Bus Interface Signals 5.3.2.5. Termination Signals
5.4. I/O Standards x
5.4.1. Input Buffer Reference Voltage (VREF) 5.4.2. On-Chip Termination (OCT)
5.4.1. Input Buffer Reference Voltage (VREF) x
5.4.1.1. Calibrated VREF Settings
5.4.2. On-Chip Termination (OCT) x
5.4.2.1. RZQ_GROUP Assignment 5.4.2.2. Manual Insertion of OCT Block
5.5. Design Guidelines x
5.5.1. Guidelines: Group Pin Placement 5.5.2. Reference Clock 5.5.3. Reset 5.5.4. Constraining Multiple PHY Lite for Parallel Interfaces Intel® FPGA IP to One I/O Bank 5.5.5. Dynamic Reconfiguration 5.5.6. Timing
5.5.6. Timing x
5.5.6.1. Timing Components 5.5.6.2. Timing Constraints and Files 5.5.6.3. Timing Analysis 5.5.6.4. Timing Closure Guidelines
5.5.6.2. Timing Constraints and Files x
5.5.6.2.1. <variation_name>.sdc 5.5.6.2.2. <variation_name>_parameter.tcl 5.5.6.2.3. <variation_name>_ip_parameters.tcl 5.5.6.2.4. <variation_name>_pin_map.tcl 5.5.6.2.5. <variation_name>_report_timing.tcl 5.5.6.2.6. <variation_name>_report_timing_core.tcl
5.5.6.4. Timing Closure Guidelines x
5.5.6.4.1. Timing Closure: Dynamic Reconfiguration 5.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 5.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 5.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 5.5.6.4.5. I/O Timing Violation 5.5.6.4.6. Internal FPGA Path Timing Violation
5.6. Design Example x
5.6.1. Generating the Design Example
5.6.1. Generating the Design Example x
5.6.1.1. Design Example without Dynamic Reconfiguration 5.6.1.2. Dynamic Reconfiguration Design Examples
5.6.1.1. Design Example without Dynamic Reconfiguration x
5.6.1.1.1. Generating the Hardware Design Example 5.6.1.1.2. Generating the Simulation Design Example
5.6.1.2. Dynamic Reconfiguration Design Examples x
5.6.1.2.1. Dynamic Reconfiguration Using Finite State Machine
6. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Devices x
6.1. Release Information 6.2. Functional Description 6.3. Getting Started 6.4. I/O Standards 6.5. Design Guidelines 6.6. Design Example 6.7. Application Specific Design Example
6.2. Functional Description x
6.2.1. Top Level Interfaces 6.2.2. Clocks 6.2.3. Output Path 6.2.4. Input Path 6.2.5. Dynamic Reconfiguration
6.2.2. Clocks x
6.2.2.1. Clock Frequency Relationships
6.2.3. Output Path x
6.2.3.1. Output Path Data Alignment
6.2.4. Input Path x
6.2.4.1. Input Path Data Alignment
6.2.5. Dynamic Reconfiguration x
6.2.5.1. RTL Connectivity 6.2.5.2. Address Lookup 6.2.5.3. Reconfiguration Features and Register Addressing 6.2.5.4. Calibration Guidelines
6.2.5.1. RTL Connectivity x
6.2.5.1.1. Daisy Chain
6.2.5.2. Address Lookup x
6.2.5.2.1. Strobes 6.2.5.2.2. Parameter Table Examples
6.2.5.3. Reconfiguration Features and Register Addressing x
6.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Address Registers 6.2.5.3.2. Control Registers Description
6.2.5.4. Calibration Guidelines x
6.2.5.4.1. Strobe Enable Window Calibration 6.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
6.3. Getting Started x
6.3.1. Parameter Settings 6.3.2. Signals
6.3.1. Parameter Settings x
6.3.1.1. Read Latency 6.3.1.2. Write Latency
6.3.2. Signals x
6.3.2.1. Clock and Reset Interface Signals 6.3.2.2. Output Path Signals 6.3.2.3. Input Path Signals 6.3.2.4. Avalon Configuration Bus Interface Signals 6.3.2.5. Termination Signals
6.4. I/O Standards x
6.4.1. Input Buffer Reference Voltage (VREF) 6.4.2. On-Chip Termination (OCT)
6.4.1. Input Buffer Reference Voltage (VREF) x
6.4.1.1. Calibrated VREF Settings
6.4.2. On-Chip Termination (OCT) x
6.4.2.1. RZQ_GROUP Assignment 6.4.2.2. Manual Insertion of OCT Block
6.5. Design Guidelines x
6.5.1. Guidelines: Group Pin Placement 6.5.2. Reference Clock 6.5.3. Reset 6.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 6.5.5. Dynamic Reconfiguration 6.5.6. Timing
6.5.6. Timing x
6.5.6.1. Timing Components 6.5.6.2. Timing Constraints and Files 6.5.6.3. Timing Analysis 6.5.6.4. Timing Closure Guidelines
6.5.6.2. Timing Constraints and Files x
6.5.6.2.1. <variation_name>.sdc 6.5.6.2.2. <variation_name>_parameter.tcl 6.5.6.2.3. <variation_name>_ip_parameters.tcl 6.5.6.2.4. <variation_name>_pin_map.tcl 6.5.6.2.5. <variation_name>_report_timing.tcl 6.5.6.2.6. <variation_name>_report_timing_core.tcl
6.5.6.4. Timing Closure Guidelines x
6.5.6.4.1. Timing Closure: Dynamic Reconfiguration 6.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 6.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 6.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 6.5.6.4.5. I/O Timing Violation 6.5.6.4.6. Internal FPGA Path Timing Violation
6.6. Design Example x
6.6.1. Generating the Design Example
6.6.1. Generating the Design Example x
6.6.1.1. Design Example without Dynamic Reconfiguration 6.6.1.2. Dynamic Reconfiguration Design Examples
6.6.1.1. Design Example without Dynamic Reconfiguration x
6.6.1.1.1. Generating the Hardware Design Example 6.6.1.1.2. Generating the Simulation Design Example
6.6.1.2. Dynamic Reconfiguration Design Examples x
6.6.1.2.1. Dynamic Reconfiguration with Debug Kit 6.6.1.2.2. Dynamic Reconfiguration Using Finite State Machine
6.7. Application Specific Design Example x
6.7.1. Implementation using the PHY Lite for Parallel Interfaces Intel® FPGA IP
1. About the PHY Lite for Parallel Interfaces IP
2. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices
3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices
6. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Devices
7. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives
8. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

4.4.2.1. RZQ_GROUP Assignment

The RZQ_GROUP assignment creates the OCT Intel® FPGA IP without modifying the RTL. The Fitter searches for the rzq pin name in the netlist. If the pin does not exist, the Fitter creates the pin name along with the OCT Intel FPGA IP and its corresponding connections. This allows you to create a group of pins to be calibrated by an existing or non-existing OCT and the Fitter ensures the legality of the design. You must associate the terminated pins of the PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series devices instance with an RZQ pin at the system level manually.

Use the following steps to set RZQ pin locations for the IP:

  1. Generate the IP or instantiate the IP into your project.
  2. You can view the available RZQ pins location in the Pin Planner. Go to Pin Planner > Tasks > OCT Pins and double click the RZQ. The available RZQ pins are display in the pin grid diagram.
  3. You can modify the qsf in your project to change the default RZQ location using the following command: 
    set_location_assignment <rzq_capable_pin_location> –to <user_defined_rzq_pin_name>
    Note: Ensure that you specify <user_defined_rzq_pin_name> in all lower-case characters, as the RZQ location assignment is case-sensitive and requires lower-case characters.
  4. Use the following command to associate the terminated pins of the IP with the RZQ pin: 
    set_instance_assignment -name RZQ_GROUP <rzq_pin_name> -to <phylite_strobe_pin>
    set_instance_assignment -name RZQ_GROUP <rzq_pin_name> -to <phylite_data_pin[*]>
    where * represents all the data pins within the same group.
    This is an example of a qsf file with modified RZQ pin location assignments: 
    set_location_assignment PIN_AH3 -to octrzq
set_instance_assignment -name IO_STANDARD "1.5 V" -to octrzq
set_instance_assignment -name RZQ_GROUP OCTRZQ -to group_0_io_interface_conduit_end_io_strobe_io
set_instance_assignment -name RZQ_GROUP OCTRZQ -to group_0_io_interface_conduit_end_io_data_io[*]
  5. Compile the project.
  6. To verify that the Quartus® Prime has successfully created and assigned the RZQ pin to the correct location, go to Pin Planner > Node Name and look for <user_defined_rzq_pin_name> with the assigned pin location in the list.
Level Two Title