External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide

Download PDF
ID 772538
Date 6/26/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP 2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction 3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture 4. Intel Agilex® 7 M-Series FPGA EMIF IP – End-User Signals 5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP 6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support 7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support 8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support 9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure 10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization 11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging 12. Document Revision History for External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP x
1.1. Release Information
2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction x
2.1. Intel Agilex® 7 M-Series EMIF IP Protocol and Feature Support 2.2. Intel Agilex® 7 M-Series EMIF IP Design Flow 2.3. Intel Agilex® 7 M-Series EMIF IP Design Checklist
3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture x
3.1. Intel Agilex® 7 M-Series EMIF Architecture: Introduction 3.2. Intel Agilex® 7 M-Series EMIF Sequencer 3.3. Intel Agilex® 7 M-Series EMIF Controller 3.4. Intel Agilex® 7 M-Series EMIF IP for Hard Processor Subsystem (HPS)
3.1. Intel Agilex® 7 M-Series EMIF Architecture: Introduction x
3.1.1. Intel Agilex® 7 M-Series EMIF Architecture: I/O Subsystem 3.1.2. Intel Agilex® 7 M-Series EMIF Architecture: I/O SSM 3.1.3. Intel Agilex® 7 M-Series EMIF Architecture: I/O Bank 3.1.4. Intel Agilex® 7 M-Series EMIF Architecture: I/O Lane 3.1.5. Intel Agilex® 7 M-Series EMIF Architecture: Input DQS Clock Tree 3.1.6. Intel Agilex® 7 M-Series EMIF Architecture: PHY Clock Tree 3.1.7. Intel Agilex® 7 M-Series EMIF Architecture: PLL Reference Clock Networks 3.1.8. Intel Agilex® 7 M-Series EMIF Architecture: Clock Phase Alignment 3.1.9. User Clock in Different Core Access Modes
3.1.3. Intel Agilex® 7 M-Series EMIF Architecture: I/O Bank x
3.1.3.1. DDR4 Pin Placement 3.1.3.2. DDR5 Pin Placement 3.1.3.3. LPDDR5 Pin Placement 3.1.3.4. I/O Sub-Bank Usage
3.2. Intel Agilex® 7 M-Series EMIF Sequencer x
3.2.1. Intel Agilex® 7 M-Series Mailbox Structure and Register Definitions
3.2.1. Intel Agilex® 7 M-Series Mailbox Structure and Register Definitions x
3.2.1.1. Mailbox Supported Commands 3.2.1.2. Mailbox Command Definitions
3.3. Intel Agilex® 7 M-Series EMIF Controller x
3.3.1. Hard Memory Controller
3.3.1. Hard Memory Controller x
3.3.1.1. Hard Memory Controller Features
4. Intel Agilex® 7 M-Series FPGA EMIF IP – End-User Signals x
4.1. Intel Agilex® 7 M-Series FPGA EMIF IP for DDR4 Interfaces 4.2. Intel Agilex® 7 M-Series FPGA EMIF IP for DDR5 Interfaces 4.3. Intel Agilex® 7 M-Series EMIF IP for LPDDR5 Interfaces
4.1. Intel Agilex® 7 M-Series FPGA EMIF IP for DDR4 Interfaces x
4.1.1. ref_clk for EMIF 4.1.2. core_init_n for EMIF 4.1.3. usr_async_clk for EMIF 4.1.4. usr_clk for EMIF 4.1.5. usr_rst_n for EMIF 4.1.6. s0_axi4 for EMIF 4.1.7. mem for EMIF 4.1.8. oct for EMIF 4.1.9. s0_axil_clk for EMIF 4.1.10. s0_axil_rst_n for EMIF 4.1.11. s0_axil for EMIF
4.2. Intel Agilex® 7 M-Series FPGA EMIF IP for DDR5 Interfaces x
4.2.1. ref_clk for EMIF 4.2.2. core_init_n for EMIF 4.2.3. usr_async_clk for EMIF 4.2.4. usr_clk for EMIF 4.2.5. usr_rst_n for EMIF 4.2.6. s0_axi4 for EMIF 4.2.7. mem for EMIF 4.2.8. oct for EMIF 4.2.9. s0_axil_clk for EMIF 4.2.10. s0_axil_rst_n for EMIF 4.2.11. s0_axil for EMIF
4.3. Intel Agilex® 7 M-Series EMIF IP for LPDDR5 Interfaces x
4.3.1. ref_clk for EMIF 4.3.2. core_init_n for EMIF 4.3.3. usr_async_clk for EMIF 4.3.4. usr_clk for EMIF 4.3.5. usr_rst_n for EMIF 4.3.6. s0_axi4 for EMIF 4.3.7. mem for EMIF 4.3.8. oct for EMIF 4.3.9. s0_axil_clk for EMIF 4.3.10. s0_axil_rst_n for EMIF 4.3.11. s0_axil for EMIF
5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP x
5.1. Simulation Walkthrough
5.1. Simulation Walkthrough x
5.1.1. Calibration 5.1.2. Simulation Scripts 5.1.3. Functional Simulation with Verilog HDL 5.1.4. Simulating the Design Example
6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support x
6.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR4 6.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning 6.3. DDR4 Board Design Guidelines
6.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR4 x
6.1.1. Intel Agilex® 7 M-Series FPGA EMIF IP Parameter Descriptions for DDR4 Interfaces 6.1.2. Intel Agilex® 7 FPGA EMIF Calibration IP Parameter Descriptions
6.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
6.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 6.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 6.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 6.2.4. Pin Placements for Intel Agilex® 7 M-Series FPGA DDR4 EMIF IP
6.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
6.2.1.1. Estimating Pin Requirements 6.2.1.2. DIMM Options 6.2.1.3. Maximum Number of Interfaces
6.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
6.2.2.1. OCT 6.2.2.2. PLL
6.2.4. Pin Placements for Intel Agilex® 7 M-Series FPGA DDR4 EMIF IP x
6.2.4.1. Address and Command Pin Placement for DDR4 6.2.4.2. DDR4 Data Width Mapping 6.2.4.3. General Guidelines - DDR4 6.2.4.4. x4 DIMM Implementation 6.2.4.5. Specific Pin Connection Requirements 6.2.4.6. Command and Address Signals 6.2.4.7. Clock Signals 6.2.4.8. Data, Data Strobes, DM/DBI, and Optional ECC Signals
6.3. DDR4 Board Design Guidelines x
6.3.1. Terminations for DDR4 with Intel Agilex® 7 M-Series Devices 6.3.2. General Layout Routing Guidelines 6.3.3. Reference Stackup 6.3.4. Intel Agilex® 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies 6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies
6.3.1. Terminations for DDR4 with Intel Agilex® 7 M-Series Devices x
6.3.1.1. Dynamic On-Chip Termination (OCT) 6.3.1.2. Dynamic On-Die Termination (ODT) in DDR4 6.3.1.3. Choosing Terminations on Intel Agilex® 7 M-Series FPGA Devices 6.3.1.4. On-Chip Termination Recommendations for Intel Agilex® 7 M-Series FPGA Devices
6.3.4. Intel Agilex® 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies x
6.3.4.1. One DIMM per Channel (1DPC) for UDIMM, RDIMM, and SODIMM DDR4 Topologies 6.3.4.2. Skew Matching Guidelines for DIMM Configurations 6.3.4.3. Power Delivery Recommendations for the Memory / DIMM Side
6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies x
6.3.5.1. Single Rank x 8 Discrete (Component) Topology 6.3.5.2. Single Rank x 16 Discrete (Component) Topology 6.3.5.3. ADDR/CMD Reference Voltage/RESET Signal Routing Guidelines for Single Rank x 8 and Single Rank x 16 Discrete (Component) Topologies 6.3.5.4. Skew Matching Guidelines for DDR4 Discrete Configurations 6.3.5.5. Power Delivery Recommendations for DDR4 Discrete Configurations 6.3.5.6. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines
6.3.5.6. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines x
6.3.5.6.1. DDR4 Byte Lane Swapping 6.3.5.6.2. DDR4 Address and Command and CLK Lane 6.3.5.6.3. DDR4 Interface x8 Data Lane 6.3.5.6.4. DDR4 Interface x4 Data Lane
7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support x
7.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR5 7.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning
7.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR5 x
7.1.1. Intel Agilex® 7 M-Series FPGA EMIF IP Parameter Descriptions for DDR5 Interfaces 7.1.2. Intel Agilex® 7 FPGA EMIF Calibration IP Parameter Descriptions
7.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
7.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 7.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 7.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 7.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA DDR5 EMIF IP 7.2.5. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines
7.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
7.2.1.1. Estimating Pin Requirements 7.2.1.2. DIMM Options 7.2.1.3. Maximum Number of Interfaces
7.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
7.2.2.1. OCT 7.2.2.2. PLL
7.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP x
7.2.3.1. General Guidelines - DDR5 7.2.3.2. x4 DIMM Implementation 7.2.3.3. Specific Pin Connection Requirements 7.2.3.4. Command and Address Signals 7.2.3.5. Clock Signals 7.2.3.6. Data, Data Strobes, DM, and Optional ECC Signals
7.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA DDR5 EMIF IP x
7.2.4.1. Address and Command Pin Placement for DDR5 7.2.4.2. DDR5 Data Width Mapping
7.2.5. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines x
7.2.5.1. DDR5 Byte Lane Swapping 7.2.5.2. DDR5 Address and Command and CLK Lane 7.2.5.3. DDR5 Interface x8 Data Lane 7.2.5.4. DDR5 Interface x4 Data Lane
8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support x
8.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for LPDDR5 8.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning
8.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for LPDDR5 x
8.1.1. Intel Agilex® 7 M-Series FPGA EMIF IP Parameter Descriptions for LPDDR5 Interfaces 8.1.2. Intel Agilex® 7 FPGA EMIF Calibration IP Parameter Descriptions
8.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
8.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 8.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 8.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 8.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA LPDDR5 EMIF IP
8.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
8.2.1.1. Estimating Pin Requirements 8.2.1.2. DIMM Options 8.2.1.3. Maximum Number of Interfaces
8.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
8.2.2.1. OCT 8.2.2.2. PLL
8.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP x
8.2.3.1. General Guidelines - LPDDR5 8.2.3.2. Specific Pin Connection Requirements 8.2.3.3. Command and Address Signals 8.2.3.4. Clock Signals
8.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA LPDDR5 EMIF IP x
8.2.4.1. Address and Command Pin Placement for LPDDR5 8.2.4.2. LPDDR5 Data Width Mapping
9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure x
9.1. Timing Closure 9.2. Optimizing Timing
9.1. Timing Closure x
9.1.1. Timing Analysis
9.1.1. Timing Analysis x
9.1.1.1. PHY or Core
10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization x
10.1. Interface Standard 10.2. Bank Management Efficiency 10.3. Data Transfer 10.4. Improving Controller Efficiency
10.4. Improving Controller Efficiency x
10.4.1. Frequency of Operation 10.4.2. Series of Reads or Writes
11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging x
11.1. Interface Configuration Performance Issues 11.2. Functional Issue Evaluation 11.3. Timing Issue Characteristics 11.4. Verifying Memory IP Using the Signal Tap Logic Analyzer 11.5. Generating Traffic with the Test Engine IP
11.1. Interface Configuration Performance Issues x
11.1.1. Interface Configuration Bottleneck and Efficiency Issues
11.2. Functional Issue Evaluation x
11.2.1. Intel® IP Memory Model 11.2.2. Vendor Memory Model 11.2.3. Transcript Window Messages
11.3. Timing Issue Characteristics x
11.3.1. Evaluating FPGA Timing Issues 11.3.2. Evaluating External Memory Interface Timing Issues
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP
2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction
3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture
4. Intel Agilex® 7 M-Series FPGA EMIF IP – End-User Signals
5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP
6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support
7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support
8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support
9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure
10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization
11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging
12. Document Revision History for External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide

8.2.3.1. General Guidelines - LPDDR5

You should follow the recommended guidelines when performing pin placement for all external memory interface pins targeting Intel Agilex® 7 M-Series devices, whether you are using the hard memory controller or your own solution.
Note: PHY only, RLDRAMx, and QDRx are not supported with HPS.

Observe the following general guidelines when placing pins for your Intel Agilex® 7 M-Series external memory interface:

  1. Ensure that the pins of a single external memory interface reside on the same edge I/O.
  2. The address and command pins and their associated clock pins in the address and command bank must follow a fixed pin-out scheme, as defined in the table in the Address and Command Pin Placement for LPDDR5 topic.
  3. Not every byte lane can function as an address and command lane or a data lane. The pin assignment must adhere to the LPDDR5 data width mapping defined in LPDDR5 Data Width Mapping .
  4. A byte lane must not be used by both address and command pins and data pins.
  5. An external memory interface can occupy one or more banks on the same edge. When an interface must occupy multiple banks, ensure that those banks are adjacent to one another.
    • If an I/O bank is shared between two interfaces—meaning that two sub-banks belong to two different EMIF interfaces—then both the interfaces must share the same voltage.
    • Sharing of I/O lanes within a sub-bank for two different EMIF interfaces is not permitted; I/O lanes within a sub-bank can be assigned to one EMIF interface only.
  6. Any pin in the same bank that is not used by an external memory interface may not be available for use as a general purpose I/O pin:
    • For fabric EMIF, unused pins in an I/O lane assigned to an EMIF interface cannot be used as general-purpose I/O pins. In the same sub-bank, pins in an I/O lane that is not assigned to an EMIF interface, can be used as general-purpose I/O pins.
    • For HPS EMIF, unused pins in an I/O lane assigned to an EMIF interface cannot be used as general-purpose I/O pins. In the same sub-bank, pins in an I/O lane that is not assigned to an EMIF interface cannot be used as general-purpose I/O pins either.
  7. All address and command pins and their associated clock pins (CK_t and CK_c) must reside within a single sub-bank. The sub-bank containing the address and command pins is identified as the address and command sub-bank. Refer to the table in LPDDR5 Data Width Mapping for the supported address and command and data lane placements for DDR5.
  8. The address and command pins and their associated clock pins in the address and command bank must follow a fixed pin-out scheme, as defined in the Intel Agilex® 7 M-Series External Memory Interface Pin Information file.
  9. An external memory interface can occupy one or more banks on the same edge. When an interface must occupy multiple banks, ensure the following:
    • That the banks are adjacent to one another.
    • That you used only the supported data width mapping as defined in the table in LPDDR5 Data Width Mapping . Be aware that not every byte lane can be used as an address and command lane or a data lane.
  10. An unused I/O lane in the address and command sub-bank can serve to implement a data group, such as a x8 DQS group. The data group must be from the same controller as the address and command signals.
  11. An I/O lane must not be used by both address and command pins and data pins.
  12. Place read data groups according to the DQS grouping in the pin table and Pin Planner. Read data strobes (such as RDQS_t and RDQS_c) must reside at physical pins capable of functioning as RDQS_t and RDQS_c for a specific read data group size. You must place the associated read data pins (DQ), within the same group.
  13. One of the sub-banks in the device (typically the sub-bank within corner bank 3A) may not be available if you use certain device configuration schemes. For some schemes, there may be an I/O lane available for EMIF data group.
    • AVST-8 – This is contained entirely within the SDM, therefore all lanes of sub-bank 3A can be used by the external memory interface.
    • AVST-16/AVST-32– Lanes 4, 5, 6, and 7 are all effectively occupied and are not usable by the external memory interface.
  14. Two memory interfaces cannot share an I/O 48 sub-bank.
Level Two Title