P-Tile Avalon® Streaming Intel® FPGA IP for PCI Express* User Guide

ID 683059
Date 6/20/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

B. Root Port Enumeration

This chapter provides a flow chart that explains the Root Port enumeration process.

The goal of enumeration is to find all connected devices in the system and for each connected device, set the necessary registers and make address range assignments.

At the end of the enumeration process, the Root Port (RP) must set the following registers:
  • Primary Bus, Secondary Bus and Subordinate Bus numbers
  • Memory Base and Limit
  • IO Base and IO Limit
  • Max Payload Size
  • Memory Space Enable bit
The Endpoint (EP) must also have the following registers set by the RP:
  • Master Enable bit
  • BAR Address
  • Max Payload Size
  • Memory Space Enable bit
  • Severity bit

The figure below shows an example tree of connected devices on which the following flow chart will be based.

Figure 93. Tree of Connected Devices in Example System
Figure 94. Root Port Enumeration Flow Chart

Figure 95. Root Port Enumeration Flow Chart (continued)

Figure 96. Root Port Enumeration Flow Chart (continued)

Notes:
  1. Vendor ID and Device ID information is located at offset 0x00h for both Header Type 0 and Header Type 1.
  2. For PCIe Gen4, the Header Type is located at offset 0x0Eh (2nd DW). If bit 0 is set to 1, it indicates the device is a Bridge; otherwise, it is an EP. If bit 7 is set to 0, it indicates this is a single-function device; otherwise, it is a multi-function device.
  3. List of capability registers for RP and non-RP devices:
    • 0x34h – Capabilities Pointers. This register is used to point to a linked list of capabilities implemented by a Function:
      1. Capabilities Pointer for RP
        1. Address 40 - Identifies the Power Management Capability ID
        2. Address 50 - Identifies MSI Capability ID
        3. Address 70 - Identifies the PCI Express Capability structure
      2. Capabilities Pointer for non-RP
        1. Address 40 - Identifies Power Management Capability ID
        2. Address 48 - Identifies the PCI Express Capability structure
  4. EP does not have an associated register of Primary, Secondary and Subordinate Bus numbers.
  5. Bridge/Switch IO Base and Limit register offset 0x1Ch. These registers are set per the PCIe 4.0 Base Specification. For more accurate information and flow, refer to chapter 7.5.1.3.6 of the Base Specification.
  6. For EP Type 0 header, BAR addresses are located at the following offsets:
    1. 0x10h – Base Address 0
    2. 0x14h – Base Address 1
    3. 0x18h – Base Address 2
    4. 0x1ch – Base Address 3
    5. 0x20h – Base Address 4
    6. 0x24h – Base Address 5
  7. For Bridge/Switch Type 1 header, BAR addresses are located at the following offsets:
    1. 0x10h – Base Address 0
    2. 0x14h – Base Address 1
  8. For Bridge/Switch Type 1 header, IO Base and IO limit registers are located at offset 0x1Ch.
  9. For Bridge/Switch Type 1 header, Non-Prefetchable Memory Base and Limit registers are located at offset 0x20h.
  10. For Bridge/Switch Type 1 header, Prefetchable Memory Base and Limit registers are located at offset 0x24h.
  11. For Bridge/Switch/EP Type 0 & 1 headers, the Bus Master Enable bit is located at offset 0x04h (Command Register) bit 2.
  12. For Bridge/Switch/EP Type 0 & 1 headers,
    1. IO Space Enable bit is located at offset 0x04h (Command Register) bit 0.
    2. Memory Space Enable bit is located at offset 0x04h (Command Register) bit 1.
    3. Bus Master Enable bit is located at offset 0x04h (Command Register) bit 2.
    4. Parity Error Response bit is located at offset 0x04h (Command Register) bit 6.
    5. SERR# Enable bit is located at offset 0x04h (Command Register) bit 8.
    6. Interrupt Disable bit is located at offset 0x04h (Command Register) bit 10.