Intel® Quartus® Prime Standard Edition User Guide: Timing Analyzer

Download PDF
ID 683068
Date 2/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Timing Analysis Introduction 2. Using the Intel® Quartus® Prime Timing Analyzer A. Intel® Quartus® Prime Standard Edition User Guides
1. Timing Analysis Introduction x
1.1. Timing Analysis Basic Concepts 1.2. Document Revision History
1.1. Timing Analysis Basic Concepts x
1.1.1. Timing Path and Clock Analysis 1.1.2. Clock Setup Analysis 1.1.3. Clock Hold Analysis 1.1.4. Recovery and Removal Analysis 1.1.5. Multicycle Path Analysis 1.1.6. Metastability Analysis 1.1.7. Timing Pessimism 1.1.8. Clock-As-Data Analysis 1.1.9. Multicorner Analysis
1.1.1. Timing Path and Clock Analysis x
1.1.1.1. The Timing Netlist 1.1.1.2. Timing Paths 1.1.1.3. Data and Clock Arrival Times 1.1.1.4. Launch and Latch Edges
1.1.5. Multicycle Path Analysis x
1.1.5.1. Multicycle Clock Hold 1.1.5.2. Multicycle Clock Setup
2. Using the Intel® Quartus® Prime Timing Analyzer x
2.1. Enhanced Timing Analysis for Intel® Arria® 10 Devices 2.2. Basic Timing Analysis Flow 2.3. Using Timing Constraints 2.4. Timing Analyzer Tcl Commands 2.5. Timing Analysis of Imported Compilation Results 2.6. Using the Intel® Quartus® Prime Timing Analyzer Document Revision History
2.2. Basic Timing Analysis Flow x
2.2.1. Step 1: Open a Project and Run the Fitter 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Specify General Timing Analyzer Settings 2.2.4. Step 4: Run Timing Analysis 2.2.5. Step 5: Analyze Timing Analysis Results
2.2.5. Step 5: Analyze Timing Analysis Results x
2.2.5.1. Timing Report Commands 2.2.5.2. Set Operating Conditions 2.2.5.3. Fmax Summary Report 2.2.5.4. Report Timing Command 2.2.5.5. Correlating Constraints to the Timing Report 2.2.5.6. Locating Timing Paths in Other Tools
2.3. Using Timing Constraints x
2.3.1. Recommended Initial SDC Constraints 2.3.2. SDC File Precedence 2.3.3. Iterative Constraint Modification 2.3.4. Creating Clocks and Clock Constraints 2.3.5. Creating I/O Constraints 2.3.6. Creating Delay and Skew Constraints 2.3.7. Creating Timing Exceptions 2.3.8. Example Circuit and SDC File
2.3.1. Recommended Initial SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.4. Creating Clocks and Clock Constraints x
2.3.4.1. Creating Base Clocks 2.3.4.2. Creating Virtual Clocks 2.3.4.3. Creating Generated Clocks (create_generated_clock) 2.3.4.4. Deriving PLL Clocks 2.3.4.5. Creating Clock Groups (set_clock_groups) 2.3.4.6. Accounting for Clock Effect Characteristics
2.3.4.1. Creating Base Clocks x
2.3.4.1.1. Automatic Clock Detection and Constraint Creation
2.3.4.2. Creating Virtual Clocks x
2.3.4.2.1. Specifying I/O Interface Uncertainty 2.3.4.2.2. I/O Interface Clock Uncertainty Example
2.3.4.3. Creating Generated Clocks (create_generated_clock) x
2.3.4.3.1. Clock Divider Example (-divide_by) 2.3.4.3.2. Clock Multiplexor Example
2.3.4.5. Creating Clock Groups (set_clock_groups) x
2.3.4.5.1. Exclusive Clock Groups (-exclusive) 2.3.4.5.2. Asynchronous Clock Groups (-asynchronous) 2.3.4.5.3. set_clock_groups Constraint Tips
2.3.4.6. Accounting for Clock Effect Characteristics x
2.3.4.6.1. Set Clock Latency (set_clock_latency) 2.3.4.6.2. Clock Uncertainty
2.3.5. Creating I/O Constraints x
2.3.5.1. Input Constraints (set_input_delay) 2.3.5.2. Output Constraints (set_output_delay)
2.3.6. Creating Delay and Skew Constraints x
2.3.6.1. Advanced I/O Timing and Board Trace Model Delay 2.3.6.2. Maximum Skew (set_max_skew) 2.3.6.3. Net Delay (set_net_delay) 2.3.6.4. Create Timing Netlist
2.3.7. Creating Timing Exceptions x
2.3.7.1. Timing Constraint Precedence 2.3.7.2. False Paths (set_false_path) 2.3.7.3. Minimum and Maximum Delays 2.3.7.4. Multicycle Paths 2.3.7.5. Multicycle Exception Examples 2.3.7.6. Delay Annotation
2.3.7.4. Multicycle Paths x
2.3.7.4.1. Common Multicycle Applications 2.3.7.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.3.7.4.3. Accounting for a Phase Shift (-phase)
2.3.7.5. Multicycle Exception Examples x
2.3.7.5.1. Default Multicycle Analysis 2.3.7.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.3.7.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.3.7.5.4. Same Frequency Clocks with Destination Clock Offset 2.3.7.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.3.7.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.3.7.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency Multicycle Constraint 2.3.7.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.4. Timing Analyzer Tcl Commands x
2.4.1. The quartus_sta Executable 2.4.2. Collection Commands 2.4.3. Identifying the Intel® Quartus® Prime Software Executable from the SDC File
2.4.2. Collection Commands x
2.4.2.1. Wildcard Characters 2.4.2.2. Adding and Removing Collection Items 2.4.2.3. Query of Collections 2.4.2.4. Using the get_pins Command
1. Timing Analysis Introduction
2. Using the Intel® Quartus® Prime Timing Analyzer
A. Intel® Quartus® Prime Standard Edition User Guides

2.3.7.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency

In this example, the source clock frequency value of 5 ns is an integer multiple of the destination clock frequency of 10 ns. The source clock frequency can be an integer multiple of the destination clock frequency when a PLL generates both clocks and use different multiplication and division factors.

In the following example the source clock frequency is a multiple of the destination clock frequency:

Figure 98. Source Clock Frequency is Multiple of Destination Clock Frequency:

The following timing diagram shows the default setup check analysis the Timing Analyzer performs:

Figure 99. Default Setup Check Analysis
Figure 100. Setup Check Calculation

The setup relationship demonstrates that the data launched at edge one does not require capture, and the data launched at edge two requires capture; therefore, you can relax the setup requirement. To correct the default analysis, you shift the launch edge by one clock period with a start multicycle setup exception of two.

The following multicycle exception adjusts the default analysis in this example:

Multicycle Constraint

set_multicycle_path -from [get_clocks clk_src] -to [get_clocks clk_dst] \
     -setup -start 2

The following timing diagram shows the preferred setup relationship for this example:

Figure 101. Preferred Setup Check Analysis

The following timing diagram shows the default hold check analysis the Timing Analyzer performs for a start multicycle setup value of two:

Figure 102. Default Hold Check
Figure 103. Hold Check Calculation

In this example, the hold check two is too restrictive. The data is launched next by the edge at 10 ns and must check against the data captured by the current latch edge at 10 ns, which does not occur in hold check two. To correct the default analysis, you use a start multicycle hold exception of one.

Level Two Title