Interlaken (2nd Generation) Intel® FPGA IP User Guide

Download PDF
ID 683396
Date 9/26/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Interface Signals 6. Register Map 7. Test Features 8. Interlaken (2nd Generation) Intel® FPGA IP User Guide Archives 9. Document Revision History for Interlaken (2nd Generation) Intel® FPGA IP User Guide
1. Introduction x
1.1. Features 1.2. Device Family Support 1.3. Performance and Resource Utilization 1.4. Flexible Lanes Support 1.5. Round-trip Latency 1.6. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IPs 2.2. Generated File Structure 2.3. Specifying the IP Core Parameters and Options 2.4. Simulating the IP Core 2.5. Compiling the Full Design and Programming the FPGA 2.6. Integrating Your IP Core in Your Design
2.1. Installing and Licensing Intel® FPGA IPs x
2.1.1. Intel® FPGA IP Evaluation Mode
2.6. Integrating Your IP Core in Your Design x
2.6.1. Pin Assignment 2.6.2. Adding the External PLL 2.6.3. PMA Adaptation Flow
3. Parameter Settings x
3.1. Main Parameters 3.2. PMA Adaptation Parameters
4. Functional Description x
4.1. Interfaces 4.2. IP Clocks 4.3. High Level Data Path Flow for Interlaken Mode 4.4. High Level Data Path Flow for Interlaken Look-aside Mode 4.5. Modes of Operation 4.6. Performance 4.7. IP Core Reset 4.8. M20K ECC Support 4.9. Out-of-Band Flow Control
4.3. High Level Data Path Flow for Interlaken Mode x
4.3.1. Interlaken TX Path 4.3.2. Interlaken RX Path 4.3.3. Unused Transceiver Channels
4.3.1. Interlaken TX Path x
4.3.1.1. Transmit Path Blocks 4.3.1.2. In-Band Calendar Bits on Transmit Side
4.3.2. Interlaken RX Path x
4.3.2.1. Receive Path Blocks 4.3.2.2. In-Band Calendar Bits on Receive Side 4.3.2.3. RX Errored Packet Handling
4.3.2.3. RX Errored Packet Handling x
4.3.2.3.1. Example With Errors and In-Band Calendar Bits
4.4. High Level Data Path Flow for Interlaken Look-aside Mode x
4.4.1. Interlaken Look-aside TX Path 4.4.2. Interlaken Look-aside RX Path
4.4.1. Interlaken Look-aside TX Path x
4.4.1.1. Transmit Path Blocks
4.4.2. Interlaken Look-aside RX Path x
4.4.2.1. Receive Path Blocks 4.4.2.2. RX Error Handling
4.5. Modes of Operation x
4.5.1. Interleaved and Packet Modes 4.5.2. Interlaken Mode 4.5.3. Interlaken Look-aside Mode 4.5.4. Multi-Segment Mode
4.5.2. Interlaken Mode x
4.5.2.1. Transmit User Data Interface Examples 4.5.2.2. Receive User Data Interface Example
4.5.3. Interlaken Look-aside Mode x
4.5.3.1. Transmit User Data Interface Example 4.5.3.2. Receive User Data Interface Example
4.5.4. Multi-Segment Mode x
4.5.4.1. Multi-Segment Interface Example
5. Interface Signals x
5.1. Clock and Reset Interface Signals 5.2. Transmit User Interface Signals 5.3. Receive User Interface Signals 5.4. Management Interface Signals 5.5. Reconfiguration Interface Signals 5.6. Interlaken Link and Miscellaneous Signals 5.7. External PLL Interface Signals
7. Test Features x
7.1. Internal Serial Loopback Mode 7.2. External Loopback Mode
1. Introduction
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Interface Signals
6. Register Map
7. Test Features
8. Interlaken (2nd Generation) Intel® FPGA IP User Guide Archives
9. Document Revision History for Interlaken (2nd Generation) Intel® FPGA IP User Guide

4.3.3. Unused Transceiver Channels

Unused transceiver channels can degrade in performance over time. To preserve the performance of unused transceiver channels, the Intel® Quartus® Prime software can switch the TX and RX channels on and off at a low frequency using a reference clock.

For more information about preserving the performance of unused transceiver channels refer to Unused or Idle Transceiver Channels section in the Intel Stratix 10 L- and H-tile Transceiver PHY User Guide and Unused Transceiver Channels section in the E-Tile Transceiver PHY User Guide.

Related Information
Level Two Title