1.4.3. Inferring Shift Registers in HDL Code
Shift Register Inference for Intel® Stratix® 10 and Intel® Agilex™ 7 Devices
Because of the high prevalence of registers in routing segments of the Intel® Hyperflex™ architecture, the Compiler's threshold for shift register inference is increased for Intel® Stratix® 10 and Intel® Agilex™ 7 devices. This increase in the threshold means that some logic that the Compiler infers as a shift register in a previous generation FPGA, may not be inferred as a shift register when targeting Intel® Stratix® 10 or Intel® Agilex™ 7 devices. This threshold increase allows more register retiming, thus improving overall design performance.
The following criteria apply to shift register detection and inference for Intel® Stratix® 10 and Intel® Agilex™ 7 devices.
Default shift register inference requirements for Intel® Stratix® 10 and Intel® Agilex™ 7 Devices:
- The minimum number of registers inferred in the shift register is 64. When the width of a chain of registers is 1, the chain must contain at least 69 registers for synthesis to infer a shift register. From these 69 registers, synthesis does not include the first and second registers in the chain in the inferred shift register. Synthesis places these first and second shift registers in ALMs. Synthesis infers a 64 bit long shift register with the third through sixty sixth registers. Synthesis does not include the last three registers in the chain in the inferred shift register. Rather, synthesis places the last three registers in ALMs.
- The minimum depth of registers inferred in the shift register is 32. When the width of a chain of registers is two or more, the chain must contain at least 37 register levels for synthesis to infer a shift register. As in the first requirement, synthesis does not include the first and second registers levels in each chain in the inferred shift register, nor are the last three register levels.
- With the following assignment, the total number of required registers (depth * width) drops to 37:
set_global_assignment -name ALLOW_ANY_SHIFT_REGISTER_SIZE_FOR_RECOGNITION ONNote: An additional stage of inference takes place during the early retiming stage as physical synthesis optimization recovers area for registers that have not been retimed.
- With both of the following assignments, the total number of required registers (depth * width) drops to 13:
set_global_assignment -name ALLOW_ANY_SHIFT_REGISTER_SIZE_FOR_RECOGNITION ON set_global_assignment -name PHYSICAL_SHIFT_REGISTER_INFERENCE=OFF
Shift Register Inference for Intel® Arria® 10 and Intel® Cyclone® 10 GX DevicesFor Intel® Arria® 10 devices, Analysis & Synthesis detects a group of shift registers of the same length, and implements the registers using the Shift Register Intel® FPGA IP.
For automatic detection, all of the shift registers must have the following characteristics:
- Use the same clock and clock enable
- Have no other secondary signals
- Have equally spaced taps that are at least three registers apart
Synthesis recognizes shift registers only for device families with dedicated RAM blocks. Intel® Quartus® Prime Pro Edition synthesis uses the following guidelines:
- The Intel® Quartus® Prime software determines whether to infer the Shift Register Intel® FPGA IP based on the width of the registered bus (W), the length between each tap (L), or the number of taps (N).
- If the Auto Shift Register Recognition option is set to Auto, Intel® Quartus® Prime Pro Edition synthesis determines which shift registers are implemented in RAM blocks for logic by using the following methods:
- The Optimization Technique setting
- Logic and RAM utilization information about the design
- Timing information from Timing-Driven Synthesis
- If the registered bus width is one ( W = 1 ), Intel® Quartus® Prime synthesis infers the shift register IP if the number of taps, times the length between each tap, is greater than or equal to 64 ( N x L > 64 ).
- If the registered bus width is greater than one ( W > 1 ), and the registered bus width times the number of taps times the length between each tap is greater than or equal to 32 ( W × N × L > 32 ), then Intel® Quartus® Prime synthesis the Shift Register Intel® FPGA IP.
- If the length between each tap (L) is not a power of two, Intel® Quartus® Prime synthesis needs external logic (LEs or ALMs) to decode the read and write counters, because of different sizes of shift registers. This extra decode logic eliminates the performance and utilization advantages of implementing shift registers in memory.
The registers that Intel® Quartus® Prime synthesis maps to the Shift Register Intel® FPGA IP, and places in RAM are not available in a Verilog HDL or VHDL output file for simulation tools, because their node names do not exist after synthesis.
(* ramstyle = "mlab" *) my_shift_reg
Simple Shift Register
Shift Register with Evenly Spaced Taps
Did you find the information on this page useful?