Agilex™ 7 FPGAs and SoCs Device Data Sheet: M-Series

Download PDF
ID 769310
Date 9/05/2025
Public
Document Table of Contents
Document Table of Contents x
Agilex™ 7 FPGAs and SoCs Device Data Sheet: M-Series
Agilex™ 7 FPGAs and SoCs Device Data Sheet: M-Series x
Electrical Characteristics
Electrical Characteristics x
Operating Conditions Switching Characteristics Configuration Specifications I/O Timing Programmable IOE Delay Glossary Document Revision History for the Agilex 7 FPGAs and SoCs Device Data Sheet: M-Series
Operating Conditions x
Absolute Maximum Ratings Maximum Allowed Overshoot and Undershoot Voltage Recommended Operating Conditions DC Characteristics
Recommended Operating Conditions x
Recommended Operating Conditions R-Tile Transceiver Power Supply Recommended Operating Conditions F-Tile Transceiver Power Supply Recommended Operating Conditions HPS Power Supply Operating Conditions
DC Characteristics x
Supply Current and Power Consumption GPIO-B DC Characteristics HPS I/O DC Characteristics SDM I/O DC Characteristics I/O Standard Specifications
GPIO-B DC Characteristics x
GPIO-B I/O Pin Leakage Current GPIO-B OCT Calibration Accuracy Specifications GPIO-B OCT Without Calibration Resistance Tolerance Specifications GPIO-B Pin Capacitance GPIO-B Internal Weak Pull-Up Resistor
HPS I/O DC Characteristics x
HPS I/O Pin Leakage Current HPS I/O Pin Capacitance HPS I/O Internal Weak Pull-Up Resistor HPS I/O Hysteresis Specifications for Schmitt Trigger Input
SDM I/O DC Characteristics x
SDM I/O Pin Leakage Current SDM I/O Pin Capacitance SDM I/O Internal Weak Pull-Up Resistor SDM I/O Hysteresis Specifications for Schmitt Trigger Input
I/O Standard Specifications x
GPIO-B I/O Standard Specifications HPS I/O Standard Specifications SDM I/O Standard Specifications
Switching Characteristics x
Core Performance Specifications Periphery Performance Specifications R-Tile Transceiver Performance Specifications F-Tile Transceiver Performance Specifications HPS Performance Specifications
Core Performance Specifications x
Clock Tree Specifications I/O PLL Specifications DSP Block Specifications Memory Block Specifications Local Temperature Sensor Specifications Remote Temperature Diode Specifications Voltage Sensor Specifications
Periphery Performance Specifications x
LVDS SERDES Specifications DPA Lock Time Specifications LVDS SERDES Soft-CDR Sinusoidal Jitter Tolerance Specifications Memory Standards Supported Memory Output Clock Jitter Specifications Performance Specifications of the HBM2E Interface Performance Specifications of Network on Chip (NoC) NOC Reference Clock Requirements
R-Tile Transceiver Performance Specifications x
R-Tile Transceiver Performance R-Tile Transceiver Reference Clock Specifications R-Tile Transmitter Specifications R-Tile Receiver Specifications
F-Tile Transceiver Performance Specifications x
F-Tile Transceiver Performance F-Tile Transceiver Reference Clock Specifications F-Tile Transmitter Specifications F-Tile Receiver Specifications F-Tile Electrical Compliance
HPS Performance Specifications x
HPS Clock Performance HPS Internal Oscillator Frequency HPS PLL Specifications HPS Cold Reset HPS SPI Timing Characteristics HPS SD/MMC Timing Characteristics HPS USB UPLI Timing Characteristics HPS Ethernet Media Access Controller (EMAC) Timing Characteristics HPS I2C Timing Characteristics HPS NAND Timing Characteristics HPS Trace Timing Characteristics HPS GPIO Interface HPS JTAG Timing Characteristics HPS Programmable I/O Timing Characteristics
Configuration Specifications x
General Configuration Timing Specifications POR Specifications External Configuration Clock Source Requirements JTAG Configuration Timing AS Configuration Timing Avalon® Streaming Configuration Timing Configuration Bit Stream Sizes
Agilex™ 7 FPGAs and SoCs Device Data Sheet: M-Series

F-Tile Transceiver Power Supply Recommended Operating Conditions

Table 11.  F-Tile Transceiver Power Supply Recommended Operating Conditions

To prevent F-Tile performance degradation, devices with F-Tile must not remain in a powered-up and unconfigured state for a cumulative time exceeding 12 months.

For specification status, see the Data Sheet Status table
Symbol Description Typical DC Level (V) Recommended DC Setpoint (% of Vnominal) Recommended VR Ripple (% of Vnominal) Recommended AC Transient (% of Vnominal) Maximum (DC Setpoint + Ripple + AC Transient) (% of Vnominal) Unit
VCC_HSSI_GXF F-Tile digital signal power supply 0.8 ±0.5% ±0.5% ±2%28 ±3% V
VCCFUSECORE_GXF F-Tile fuse writing power supply 1 ±0.5% ±4.5% ±5% V
VCCFUSEWR_GXF F-Tile efuse power supply 1 ±0.5% ±4.5% ±5% V
VCCCLK_GXF Reference clock power supply 1.8 ±0.5% ±0.5% ±2% ±3% V
VCCERT1_FHT_GXF 29 FHT analog core supply 1 1 ±0.5% ±0.5% ±1.5% ±2.5% V
VCCERT2_FHT_GXF 30 FHT analog core supply 2 1 ±0.5% ±0.5% ±1.5% ±2.5% V
VCCEHT_FHT_GXF 31 FHT high voltage power supply for analog circuit 1.5 ±0.5% ±0.5% +1%/–1.5% +2%/–2.5% V
VCCERT_FGT_GXF 32 FGT analog core supply alone 1 ±0.5% ±0.5% ±2% ±3% V
FGT analog core supply when combined with VCCERT1_FHT_GX and VCCERT2_FHT_GXF 1 V supply 1 ±0.5% ±0.5% ±1.5% ±2.5% V
VCCH_FGT_GXF 32 FGT analog I/O power supply 1.8 ±0.5% ≤5 mV ±1.5% ±3% V
Related Information
28 Board design can use 2.5% as indicated by AN910 if the simulation results include both VR ripple and AC transcient.
29 HF noise requires AC 10 mVpp above 1 MHz; switching regulator ripple switching frequency: <1 MHz, ripple: ≤5 mVpp.
30 HF noise requires AC 30 mVpp above 1 MHz; switching regulator ripple switching frequency: <1 MHz, ripple: ≤5 mVpp.
31 HF noise requires AC 30 mVpp above 1 MHz; switching regulator ripple switching frequency: <1 MHz, ripple: ≤7 mVpp.
32 HF noise requires AC 30 mVpp above 1 MHz; switching regulator ripple: ≤5 mVpp.
Level Two Title