50G Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683217
Date 10/31/2022
Public
Document Table of Contents
Document Table of Contents x
1. About This IP Core 2. Getting Started With the 50G Interlaken IP Core 3. 50G Interlaken IP Core Parameter Settings 4. Functional Description 5. 50G Interlaken IP core Signals 6. 50G Interlaken IP Core Register Map 7. 50G Interlaken IP Core Test Features 8. Advanced Parameter Settings 9. Out-of-Band Flow Control in the 50G Interlaken IP core 10. 50G Interlaken Intel® FPGA IP User Guide Archives 11. Document Revision History for 50G Interlaken Intel® FPGA IP User Guide A. Performance and Fmax Requirements for 40G Ethernet Traffic
1. About This IP Core x
1.1. Features 1.2. Device Family Support 1.3. IP Core Verification 1.4. Performance and Resource Utilization 1.5. Device Speed Grade Support 1.6. Release Information
1.1. Features x
1.1.1. IP Core Supported Combinations of Number of Lanes and Data Rate 1.1.2. IP Core Raw Aggregate Bandwidth
2. Getting Started With the 50G Interlaken IP Core x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the 50G Interlaken IP Core Parameters and Options 2.3. Files Generated for Arria V GZ and Stratix V Variations 2.4. Files Generated for Intel® Arria® 10 Variations 2.5. Simulating the 50G Interlaken IP Core 2.6. Integrating Your IP Core in Your Design 2.7. Compiling the Full Design and Programming the FPGA 2.8. Creating a Signal Tap Debug File to Match Your Design Hierarchy
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.6. Integrating Your IP Core in Your Design x
2.6.1. Pin Assignments 2.6.2. Transceiver Logical Channel Numbering 2.6.3. Adding the Reconfiguration Controller 2.6.4. Adding the External PLL
2.6.3. Adding the Reconfiguration Controller x
2.6.3.1. Generating the Reconfiguration Controller 2.6.3.2. Connecting the Reconfiguration Controller to the IP Core
3. 50G Interlaken IP Core Parameter Settings x
3.1. Meta Frame Length in Words 3.2. Enable Native PHY Debug Master Endpoint (NPDME) 3.3. Transceiver Reference Clock Frequency 3.4. Number of Calendar Pages 3.5. TX Scrambler Seed 3.6. Transfer Mode Selection
4. Functional Description x
4.1. Interfaces Overview 4.2. High Level Block Diagram 4.3. Clocking and Reset Structure for IP Core 4.4. Interleaved and Packet Modes 4.5. 50G Interlaken IP Core Transmit Path 4.6. 50G Interlaken IP Core Receive Path
4.1. Interfaces Overview x
4.1.1. Application Interface 4.1.2. Interlaken Interface 4.1.3. Out‑of‑Band Flow Control Interface 4.1.4. Management Interface 4.1.5. Transceiver Control Interfaces
4.1.5. Transceiver Control Interfaces x
4.1.5.1. Transceiver Reconfiguration Controller Interface 4.1.5.2. Intel® Arria® 10 External PLL Interface 4.1.5.3. Intel® Arria® 10 Transceiver Reconfiguration Interface
4.3. Clocking and Reset Structure for IP Core x
4.3.1. 50G Interlaken IP Core Clock Signals 4.3.2. IP Core Reset 4.3.3. IP Core Reset Sequence with the Reconfiguration Controller
4.5. 50G Interlaken IP Core Transmit Path x
4.5.1. 50G Interlaken IP Core Transmit User Data Interface Examples 4.5.2. 50G Interlaken IP Core In-Band Calendar Bits on Transmit Side 4.5.3. 50G Interlaken IP Core Transmit Path Blocks
4.5.1. 50G Interlaken IP Core Transmit User Data Interface Examples x
4.5.1.1. 50G Interlaken IP Core Interleaved Mode (Segmented Mode) Example 4.5.1.2. 50G Interlaken IP Core Packet Mode Operation Example 4.5.1.3. 50G Interlaken IP Core Back-Pressured Packet Transfer Example
4.5.3. 50G Interlaken IP Core Transmit Path Blocks x
4.5.3.1. 50G Interlaken IP Core TX Transmit Buffer 4.5.3.2. 50G Interlaken IP Core TX MAC 4.5.3.3. 50G Interlaken IP Core TX PCS 4.5.3.4. 50G Interlaken IP Core TX PMA
4.6. 50G Interlaken IP Core Receive Path x
4.6.1. 50G Interlaken IP Core Receive User Data Interface Examples 4.6.2. 50G Interlaken IP Core RX Errored Packet Handling 4.6.3. In-Band Calendar Bits on the 50G Interlaken IP Core Receiver User Data Interface 4.6.4. 50G Interlaken IP Core Receive Path Blocks
4.6.1. 50G Interlaken IP Core Receive User Data Interface Examples x
4.6.1.1. 50G Interlaken IP Core Receiver Side Example
4.6.2. 50G Interlaken IP Core RX Errored Packet Handling x
4.6.2.1. 50G Interlaken IP Core Receiver Side Example With Errors and In-Band Calendar Bits
4.6.4. 50G Interlaken IP Core Receive Path Blocks x
4.6.4.1. 50G Interlaken IP Core RX PMA 4.6.4.2. 50G Interlaken IP Core RX PCS 4.6.4.3. 50G Interlaken IP Core RX MAC 4.6.4.4. 50G Interlaken IP Core RX Regroup Block
5. 50G Interlaken IP core Signals x
5.1. 50G Interlaken IP Core Clock Interface Signals 5.2. 50G Interlaken IP Core Reset Interface Signals 5.3. 50G Interlaken IP Core User Data Transfer Interface Signals 5.4. 50G Interlaken IP Core Interlaken Link and Miscellaneous Interface Signals 5.5. 50G Interlaken IP Core Management Interface 5.6. Device Dependent Signals
5.6. Device Dependent Signals x
5.6.1. Transceiver Reconfiguration Controller Interface Signals 5.6.2. Intel® Arria® 10 External PLL Interface Signals 5.6.3. Intel® Arria® 10 Transceiver Reconfiguration Interface Signals
7. 50G Interlaken IP Core Test Features x
7.1. Internal Serial Loopback Mode 7.2. External Loopback Mode 7.3. PRBS Generation and Validation 7.4. CRC32 Error Injection
7.3. PRBS Generation and Validation x
7.3.1. Setting up PRBS Mode in Arria V and Stratix V Devices 7.3.2. Setting up PRBS Mode in Intel® Arria® 10 Devices
8. Advanced Parameter Settings x
8.1. Hidden Parameters 8.2. Modifying Hidden Parameter Values
8.1. Hidden Parameters x
8.1.1. Required User Clock Frequency 8.1.2. Counter Reset Bits 8.1.3. Include Temp Sense 8.1.4. RXFIFO Address Width 8.1.5. SWAP_TX_LANES and SWAP_RX_LANES (Data Word Lane Swapping) 8.1.6. Use ATX or CMU PLL 8.1.7. Lane Profile
9. Out-of-Band Flow Control in the 50G Interlaken IP core x
9.1. Out-of-Band Flow Control Block Clocks 9.2. TX Out‑of‑Band Flow Control Signals 9.3. RX Out-of-Band Flow Control Signals
1. About This IP Core
2. Getting Started With the 50G Interlaken IP Core
3. 50G Interlaken IP Core Parameter Settings
4. Functional Description
5. 50G Interlaken IP core Signals
6. 50G Interlaken IP Core Register Map
7. 50G Interlaken IP Core Test Features
8. Advanced Parameter Settings
9. Out-of-Band Flow Control in the 50G Interlaken IP core
10. 50G Interlaken Intel® FPGA IP User Guide Archives
11. Document Revision History for 50G Interlaken Intel® FPGA IP User Guide
A. Performance and Fmax Requirements for 40G Ethernet Traffic

5.5. 50G Interlaken IP Core Management Interface

The 50G Interlaken IP core management interface allows you to communicate with IP core internal status and control registers. This interface manages the PMA (resets and serial loopback controls) and PCS control and status registers. This interface does not provide access to the hard PCS registers on the device.

The management interface is a typical 32-bit memory-mapped register port. It complies with the Avalon Memory-Mapped (Avalon-MM) specification defined in the Avalon Interface Specifications.

Table 15.   50G Interlaken IP Core Management Interface Signals

Signal Name

Direction

Width (Bits)

Description

50G Interlaken IP Core Management Interface Signals

mm_clk

Input

1

Management clock. Clocks the register accesses. It is also used for clock rate monitoring and some analog calibration procedures. You must run this clock at a frequency in the range of 100 MHz–125 MHz.

mm_clk_locked

Input

1

Assert this signal to indicate that mm_clk is stable.

The IP core responds to this signal in the same way it responds to the reset_n signal: loss of lock restarts the reset sequence.

Intel® recommends that you tie this signal high and not rely on its functionality. It is expected to be deprecated in the near future.

mm_read

Input

1

Read access to the register ports.

mm_write

Input

1

Write access to the register ports.

mm_addr

Input

16

Address to access the register ports.

mm_rdata

Output

32

When mm_rdata_valid is high, mm_rdata holds valid read data.

mm_rdata_valid

Output

1

Valid signal for mm_rdata.

mm_wdata

Input

32

When mm_write is high, mm_wdata holds valid write data.

If you do not use the management interface, drive the management inputs as follows:

  • mm_clk must connect to a stable clock. However, the clock signal need not be of unusually high quality.
  • mm_clk_locked must be tied to zero.
  • mm_read and mm_write must be tied to zero.

If you use the management interface, drive the control lines as shown in the examples and observing the following constraints:

  • During a write operation, you must maintain the the mm_write signal asserted for at least two clock cycles. Back-to-back writes must be separated by at least one clock cycle.
  • During a read operation, you must maintain the mm_read signal asserted for at least two clock cycles. Back-to-back reads must be separated by at least one clock cycle.
Figure 18.  50G Interlaken IP Core Management Interface Write Operation

Shows the timing requirements for a write operation on the 50G Interlaken IP core management interface.

Figure 19.  50G Interlaken IP Core Management Interface Read Operation

Shows the timing requirements for a read operation on the 50G Interlaken IP core management interface. The IP core asserts the mm_rdata_valid signal one cycle after the mm_read signal is asserted.

Related Information
Level Two Title