AN 985: Nios® V Processor Tutorial

Download
ID 784468
Date 8/18/2023
Public
Document Table of Contents
Document Table of Contents x
1. AN 985: Nios® V Processor Tutorial
1. AN 985: Nios® V Processor Tutorial x
1.1. Overview 1.2. Generating the System 1.3. Simulating the Nios® V Processor System 1.4. Programming the System 1.5. Debugging the System 1.6. Document Revision History for AN 985: Nios® V Processor Tutorial
1.1. Overview x
1.1.1. Hardware and Software Requirements
1.2. Generating the System x
1.2.1. Creating a New Project 1.2.2. Building Hardware Design in Platform Designer 1.2.3. Building Software Design with Ashling* RiscFree* IDE for Intel® FPGAs
1.2.2. Building Hardware Design in Platform Designer x
1.2.2.1. Creating a Platform Designer System 1.2.2.2. Configuring Assignment and Constraint 1.2.2.3. Compiling the Intel® Quartus® Prime Software Project
1.2.2.1. Creating a Platform Designer System x
1.2.2.1.1. Adding Nios® V/m Processor Intel® FPGA IP 1.2.2.1.2. Adding On-Chip Memory II (RAM or ROM) Intel® FPGA IP 1.2.2.1.3. Adding JTAG UART Intel® FPGA IP 1.2.2.1.4. Adding Reset Release Intel® FPGA IP 1.2.2.1.5. Connect Interfaces and Signals 1.2.2.1.6. Clear System Warnings and Errors 1.2.2.1.7. Configuring the Reset Vector of the Nios® V Processor 1.2.2.1.8. Saving and Generating System HDL
1.2.2.2. Configuring Assignment and Constraint x
1.2.2.2.1. Adding Design Files 1.2.2.2.2. Adding Synopsys Design Constraint (SDC) File 1.2.2.2.3. Pin Assignments 1.2.2.2.4. Configuration and Power Management Assignments
1.2.3. Building Software Design with Ashling* RiscFree* IDE for Intel® FPGAs x
1.2.3.1. Creating a Board Support Package 1.2.3.2. Creating an Application Project File 1.2.3.3. Importing Projects into Ashling* RiscFree* IDE for Intel® FPGAs 1.2.3.4. Building the Hello World Application
1.2.3.3. Importing Projects into Ashling* RiscFree* IDE for Intel® FPGAs x
1.2.3.3.1. Importing Nios® V Processor BSP Project 1.2.3.3.2. Importing Application Project
1.3. Simulating the Nios® V Processor System x
1.3.1. Preparing Hardware Design for Simulation 1.3.2. Preparing Software Design for Simulation 1.3.3. Checking Simulation Files 1.3.4. Running System Simulation
1.4. Programming the System x
1.4.1. Programming Hardware SOF File 1.4.2. Downloading the Software ELF File 1.4.3. Applying External Tool Configuration 1.4.4. Run Hello World Application
1.5. Debugging the System x
1.5.1. Software Debugging
1.5.1. Software Debugging x
1.5.1.1. Setting Initial Breakpoint 1.5.1.2. Starting the Debugger 1.5.1.3. View Global Variables 1.5.1.4. View Memory 1.5.1.5. Setting a Second Breakpoint 1.5.1.6. Control Debugger
1. AN 985: Nios® V Processor Tutorial

1.4.4. Run Hello World Application

With the External Tool Configuration (Nios V JTAG UART Output) defined successfully, you may proceed to use it to display the Hello World application.

  1. Go to Run > External Tools > External Tools Configurations.
  2. Select Nios V JTAG UART Output.
  3. Click Run.
  4. The Hello World message is printed on the Console tab.
Figure 44. Hello World Message (Console tab)
Level Two Title

Did you find the information on this page useful?

Characters remaining:

Feedback Message