AN 985: Nios® V Processor Tutorial

Download
ID 784468
Date 8/18/2023
Public
Document Table of Contents
Document Table of Contents x
1. AN 985: Nios® V Processor Tutorial
1. AN 985: Nios® V Processor Tutorial x
1.1. Overview 1.2. Generating the System 1.3. Simulating the Nios® V Processor System 1.4. Programming the System 1.5. Debugging the System 1.6. Document Revision History for AN 985: Nios® V Processor Tutorial
1.1. Overview x
1.1.1. Hardware and Software Requirements
1.2. Generating the System x
1.2.1. Creating a New Project 1.2.2. Building Hardware Design in Platform Designer 1.2.3. Building Software Design with Ashling* RiscFree* IDE for Intel® FPGAs
1.2.2. Building Hardware Design in Platform Designer x
1.2.2.1. Creating a Platform Designer System 1.2.2.2. Configuring Assignment and Constraint 1.2.2.3. Compiling the Intel® Quartus® Prime Software Project
1.2.2.1. Creating a Platform Designer System x
1.2.2.1.1. Adding Nios® V/m Processor Intel® FPGA IP 1.2.2.1.2. Adding On-Chip Memory II (RAM or ROM) Intel® FPGA IP 1.2.2.1.3. Adding JTAG UART Intel® FPGA IP 1.2.2.1.4. Adding Reset Release Intel® FPGA IP 1.2.2.1.5. Connect Interfaces and Signals 1.2.2.1.6. Clear System Warnings and Errors 1.2.2.1.7. Configuring the Reset Vector of the Nios® V Processor 1.2.2.1.8. Saving and Generating System HDL
1.2.2.2. Configuring Assignment and Constraint x
1.2.2.2.1. Adding Design Files 1.2.2.2.2. Adding Synopsys Design Constraint (SDC) File 1.2.2.2.3. Pin Assignments 1.2.2.2.4. Configuration and Power Management Assignments
1.2.3. Building Software Design with Ashling* RiscFree* IDE for Intel® FPGAs x
1.2.3.1. Creating a Board Support Package 1.2.3.2. Creating an Application Project File 1.2.3.3. Importing Projects into Ashling* RiscFree* IDE for Intel® FPGAs 1.2.3.4. Building the Hello World Application
1.2.3.3. Importing Projects into Ashling* RiscFree* IDE for Intel® FPGAs x
1.2.3.3.1. Importing Nios® V Processor BSP Project 1.2.3.3.2. Importing Application Project
1.3. Simulating the Nios® V Processor System x
1.3.1. Preparing Hardware Design for Simulation 1.3.2. Preparing Software Design for Simulation 1.3.3. Checking Simulation Files 1.3.4. Running System Simulation
1.4. Programming the System x
1.4.1. Programming Hardware SOF File 1.4.2. Downloading the Software ELF File 1.4.3. Applying External Tool Configuration 1.4.4. Run Hello World Application
1.5. Debugging the System x
1.5.1. Software Debugging
1.5.1. Software Debugging x
1.5.1.1. Setting Initial Breakpoint 1.5.1.2. Starting the Debugger 1.5.1.3. View Global Variables 1.5.1.4. View Memory 1.5.1.5. Setting a Second Breakpoint 1.5.1.6. Control Debugger
1. AN 985: Nios® V Processor Tutorial

1.4.1. Programming Hardware SOF File

  1. Connect the Intel Agilex 7 FPGA F-Series Transceiver-SoC Development Kit to the host PC using the Intel FPGA Download Cable II.
  2. Open the Intel Quartus Prime Programmer.
    Figure 35. Intel Quartus Prime Programmer
  3. Click Hardware Setup.
  4. Check the availability of the development kit in Available hardware items.
    1. If available, select the development kit in Currently selected hardware.
    2. If not available, check the cable connection, and the JtagServer driver installation.
    Figure 36. Hardware Setup
  5. Click Auto Detect and select the appropriate device OPN.
  6. Select the Intel Agilex device, click Change File and select niosv_top.sof file.
  7. Once the SOF file is ready, check Program/Configure and click Start.
    Figure 37. List of Devices with JTAG Chain
  8. Wait until the Progress bar reaches 100% (Successful).
    Figure 38. Progress Bar
  9. You have successfully configured the development kit with the processor hardware system.
Level Two Title

Did you find the information on this page useful?

Characters remaining:

Feedback Message