Accelerator Functional Unit Developer Guide: Intel FPGA Programmable Acceleration Card N3000 Variants

Download PDF
ID 683190
Date 7/15/2022
Public
Document Table of Contents
Document Table of Contents x
1. About This Document 2. Introduction 3. High Level Description 4. Creating an N3000 FPGA Design 5. Capturing Signals in AFU with Signal Tap 6. Document Revision History for the Accelerator Functional Unit Developer Guide: Intel FPGA Programmable Acceleration Card N3000 Variants
1. About This Document x
1.1. Acronym List
2. Introduction x
2.1. Base Knowledge and Skills Prerequisites
2.1. Base Knowledge and Skills Prerequisites x
2.1.1. Considerations
3. High Level Description x
3.1. Steps for Creating Your AFU 3.2. N3000 Block Diagram 3.3. Factory Image Description
3.2. N3000 Block Diagram x
3.2.1. In-Line Data Path 3.2.2. Supported Ethernet Network Configurations 3.2.3. Provided Files 3.2.4. Internal Interfaces
3.2.3. Provided Files x
3.2.3.1. Directory Structure
3.2.4. Internal Interfaces x
3.2.4.1. Core Cache Interface (CCI-P) 3.2.4.2. Ethernet Interface 3.2.4.3. Ethernet MAC 3.2.4.4. 40G – 25G Gearbox 3.2.4.5. External Memory Interfaces 3.2.4.6. Ethernet MAC Wrapper Register Access
3.2.4.1. Core Cache Interface (CCI-P) x
3.2.4.1.1. FPGA Internal Register Access
3.2.4.5. External Memory Interfaces x
3.2.4.5.1. DDR4A and DDR4B 3.2.4.5.2. DDR4C 3.2.4.5.3. QDR4 Interface
4. Creating an N3000 FPGA Design x
4.1. Create New Project Directory 4.2. Create Your AFU Design Files 4.3. Build with make 4.4. Check Timing 4.5. Loading Your AFU into the Intel FPGA PAC N3000
4.2. Create Your AFU Design Files x
4.2.1. ccip_std_afu.sv 4.2.2. AFU File 4.2.3. QSF File 4.2.4. SDC File
4.5. Loading Your AFU into the Intel FPGA PAC N3000 x
4.5.1. Loading Your FPGA Image with JTAG 4.5.2. AFU Clocks 4.5.3. Creating an AFU with High Level Synthesis (HLS)
4.5.1. Loading Your FPGA Image with JTAG x
4.5.1.1. Preparing Your N3000 for JTAG 4.5.1.2. Disabling PCIe* Automatic Error Reporting (AER) 4.5.1.3. Using JTAG to Load the Intel® Arria® 10 *.sof file 4.5.1.4. How to Rescan PCIe* Bus and Re-enable PCIe* AER
4.5.2. AFU Clocks x
4.5.2.1. Hello AFU Example (uClk_usr) 4.5.2.2. Hello AFU Example (pll)
4.5.3. Creating an AFU with High Level Synthesis (HLS) x
4.5.3.1. Setting Up a Shell for HLS Development Work 4.5.3.2. Using the Initial Shell Design as a Shell 4.5.3.3. Compiling the Design and Producing a new N3000 FPGA Bitstream 4.5.3.4. Verifying Timing Constraints are Satisfied
5. Capturing Signals in AFU with Signal Tap x
5.1. Adding Signal Tap to the Design 5.2. Loading FPGA Image 5.3. Set Up Connections 5.4. How to Exit from the Debug Session 5.5. Troubleshooting Remote Debug Connections
1. About This Document
2. Introduction
3. High Level Description
4. Creating an N3000 FPGA Design
5. Capturing Signals in AFU with Signal Tap
6. Document Revision History for the Accelerator Functional Unit Developer Guide: Intel FPGA Programmable Acceleration Card N3000 Variants

6. Document Revision History for the Accelerator Functional Unit Developer Guide: Intel FPGA Programmable Acceleration Card N3000 Variants

Document Version Intel Acceleration Stack Version Changes
2022.07.15 1.3.1 Updated the Target list in section: Build with make .
2020.09.08 1.3.1 Updated in accordance with the Intel Acceleration Stack 1.3.1 Version for Intel FPGA Programmable Acceleration Card N3000.
2020.06.15 1.3 Added enhancements for 1.3:
  • Supported Ethernet Network Configurations—Added supported Board OPN
  • Ethernet Interface—Updated the Instantiated Ethernet MACs figure to reflect that in the 4x25, only one QSFP and one Retimer are active.
  • Added the following sections:
    • Loading Your FPGA image with JTAG
    • Prepare your N3000 for JTAG
    • Disable PCIe Automatic Error Reporting (AER)
    • Use JTAG to load A10 *.sof file
    • How to rescan PCIe bus and re-enable PCIe AER
    • AFU Clocks
    • Hello_afu – uClk_usr
    • Hello_afu – New PLL
    • Creating an AFU with High Level Synthesis (HLS)
2019.12.06 1.1 Initial Release
Level Two Title