PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

Download PDF
ID 683716
Date 1/12/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the PHY Lite for Parallel Interfaces IP 2. PHY Lite for Parallel Interfaces Intel® FPGA IP (phylite_ph2) for Intel Agilex® 7 M-Series Devices 3. PHY Lite for Parallel Interfaces Intel® FPGA IP (altera_phylite_s20) for Intel Agilex® 7 F-Series and I-Series Devices 4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices 5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices 6. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives 7. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide
1. About the PHY Lite for Parallel Interfaces IP x
1.1. Device Family Support 1.2. Features
2. PHY Lite for Parallel Interfaces Intel® FPGA IP (phylite_ph2) for Intel Agilex® 7 M-Series Devices x
2.1. Release Information 2.2. Functional Description 2.3. Getting Started 2.4. I/O Standards 2.5. Design Example
2.2. Functional Description x
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for M-Series Devices Top Level Interfaces 2.2.2. Dynamic Reconfiguration 2.2.3. I/O Timing
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for M-Series Devices Top Level Interfaces x
2.2.1.1. Clocks 2.2.1.2. Output Path 2.2.1.3. Input Path
2.2.1.1. Clocks x
2.2.1.1.1. Clock Frequency Relationships
2.2.2. Dynamic Reconfiguration x
2.2.2.1. Calibration IP 2.2.2.2. Dynamic Reconfigurable Delays 2.2.2.3. Register Map
2.3. Getting Started x
2.3.1. Parameter Settings 2.3.2. Signals
2.3.2. Signals x
2.3.2.1. Clock and Reset Interface Signals 2.3.2.2. Output Path Signals 2.3.2.3. Input Path Signals
2.4. I/O Standards x
2.4.1. Design Guidelines
2.4.1. Design Guidelines x
2.4.1.1. DQS Trees 2.4.1.2. Pin Placement Restrictions
2.5. Design Example x
2.5.1. Generating the Design Example 2.5.2. Verifying Simulation Design Examples using Tester IP
2.5.1. Generating the Design Example x
2.5.1.1. Design Example without Dynamic Reconfiguration 2.5.1.2. Dynamic Reconfiguration Design Examples
2.5.1.1. Design Example without Dynamic Reconfiguration x
2.5.1.1.1. Generating the Synthesis Design Example 2.5.1.1.2. Generating the Simulation Design Example
2.5.1.2. Dynamic Reconfiguration Design Examples x
2.5.1.2.1. Generating the Synthesis Design Example 2.5.1.2.2. Generating the Simulation Design Example
3. PHY Lite for Parallel Interfaces Intel® FPGA IP (altera_phylite_s20) for Intel Agilex® 7 F-Series and I-Series Devices x
3.1. Release Information 3.2. Functional Description 3.3. Getting Started 3.4. I/O Standards 3.5. Design Guidelines 3.6. Design Example
3.2. Functional Description x
3.2.1. Intel Agilex® 7 F-Series and I-Series I/O Sub-bank Interconnects 3.2.2. Intel Agilex® 7 F-Series and I-Series Input DQS/Strobe Tree 3.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series Devices Top Level Interfaces 3.2.4. Dynamic Reconfiguration 3.2.5. I/O Timing
3.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series Devices Top Level Interfaces x
3.2.3.1. Clocks 3.2.3.2. Output Path 3.2.3.3. Input Path
3.2.3.1. Clocks x
3.2.3.1.1. Clock Frequency Relationships
3.2.4. Dynamic Reconfiguration x
3.2.4.1. Connectivity 3.2.4.2. Reconfiguration Features and Register Addressing 3.2.4.3. Dynamic Reconfiguration Guidelines
3.2.4.2. Reconfiguration Features and Register Addressing x
3.2.4.2.1. Control Registers Addresses 3.2.4.2.2. Control Registers
3.2.4.3. Dynamic Reconfiguration Guidelines x
3.2.4.3.1. Strobe Enable Window Calibration 3.2.4.3.2. Output and Strobe Enable Minimum and Maximum Phase Settings 3.2.4.3.3. Input DQ/DQS Delay Chains Maximum Values
3.3. Getting Started x
3.3.1. Parameter Settings 3.3.2. Signals
3.3.1. Parameter Settings x
3.3.1.1. Read Latency 3.3.1.2. Write Latency
3.3.2. Signals x
3.3.2.1. Clock and Reset Interface Signals 3.3.2.2. Output Path Signals 3.3.2.3. Input Path Signals
3.4. I/O Standards x
3.4.1. Input Buffer Reference Voltage (VREF) 3.4.2. On-Chip Termination (OCT)
3.4.2. On-Chip Termination (OCT) x
3.4.2.1. RZQ_GROUP Assignment
3.5. Design Guidelines x
3.5.1. Guidelines: Group Pin Placement Automatic and Manual Pin Placement 3.5.2. Reference Clock 3.5.3. Reset
3.6. Design Example x
3.6.1. Generating the Design Example
3.6.1. Generating the Design Example x
3.6.1.1. Design Example without Dynamic Reconfiguration 3.6.1.2. Dynamic Reconfiguration Design Examples
3.6.1.1. Design Example without Dynamic Reconfiguration x
3.6.1.1.1. Generating the Synthesis Design Example 3.6.1.1.2. Generating the Simulation Design Example
3.6.1.2. Dynamic Reconfiguration Design Examples x
3.6.1.2.1. Generating the Synthesis Design Example 3.6.1.2.2. Generating the Simulation Design Example
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices x
4.1. Release Information 4.2. Functional Description 4.3. Getting Started 4.4. I/O Standards 4.5. Design Guidelines 4.6. Design Example
4.2. Functional Description x
4.2.1. Top Level Interfaces 4.2.2. Clocks 4.2.3. Output Path 4.2.4. Input Path 4.2.5. Dynamic Reconfiguration
4.2.2. Clocks x
4.2.2.1. Clock Frequency Relationships
4.2.3. Output Path x
4.2.3.1. Output Path Data Alignment
4.2.4. Input Path x
4.2.4.1. Input Path Data Alignment
4.2.5. Dynamic Reconfiguration x
4.2.5.1. RTL Connectivity 4.2.5.2. Address Lookup 4.2.5.3. Reconfiguration Features and Register Addressing 4.2.5.4. Calibration Guidelines
4.2.5.1. RTL Connectivity x
4.2.5.1.1. Daisy Chain
4.2.5.2. Address Lookup x
4.2.5.2.1. Strobes 4.2.5.2.2. Parameter Table Examples
4.2.5.3. Reconfiguration Features and Register Addressing x
4.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices Control Registers Addresses 4.2.5.3.2. Control Registers Description
4.2.5.4. Calibration Guidelines x
4.2.5.4.1. Strobe Enable Window Calibration 4.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
4.3. Getting Started x
4.3.1. Parameter Settings 4.3.2. Signals
4.3.1. Parameter Settings x
4.3.1.1. Read Latency 4.3.1.2. Write Latency
4.3.2. Signals x
4.3.2.1. Clock and Reset Interface Signals 4.3.2.2. Output Path Signals 4.3.2.3. Input Path Signals 4.3.2.4. Avalon Configuration Bus Interface Signals 4.3.2.5. Termination Signals
4.4. I/O Standards x
4.4.1. Input Buffer Reference Voltage (VREF) 4.4.2. On-Chip Termination (OCT)
4.4.1. Input Buffer Reference Voltage (VREF) x
4.4.1.1. Calibrated VREF Settings
4.4.2. On-Chip Termination (OCT) x
4.4.2.1. RZQ_GROUP Assignment 4.4.2.2. Manual Insertion of OCT Block
4.5. Design Guidelines x
4.5.1. Guidelines: Group Pin Placement 4.5.2. Reference Clock 4.5.3. Reset 4.5.4. Constraining Multiple PHY Lite for Parallel Interfaces Intel® FPGA IP to One I/O Bank 4.5.5. Dynamic Reconfiguration 4.5.6. Timing
4.5.6. Timing x
4.5.6.1. Timing Components 4.5.6.2. Timing Constraints and Files 4.5.6.3. Timing Analysis 4.5.6.4. Timing Closure Guidelines
4.5.6.2. Timing Constraints and Files x
4.5.6.2.1. <variation_name>.sdc 4.5.6.2.2. <variation_name>_parameter.tcl 4.5.6.2.3. <variation_name>_ip_parameters.tcl 4.5.6.2.4. <variation_name>_pin_map.tcl 4.5.6.2.5. <variation_name>_report_timing.tcl 4.5.6.2.6. <variation_name>_report_timing_core.tcl
4.5.6.4. Timing Closure Guidelines x
4.5.6.4.1. Timing Closure: Dynamic Reconfiguration 4.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 4.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 4.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 4.5.6.4.5. I/O Timing Violation 4.5.6.4.6. Internal FPGA Path Timing Violation
4.6. Design Example x
4.6.1. Generating the Design Example
4.6.1. Generating the Design Example x
4.6.1.1. Design Example without Dynamic Reconfiguration 4.6.1.2. Dynamic Reconfiguration Design Examples
4.6.1.1. Design Example without Dynamic Reconfiguration x
4.6.1.1.1. Generating the Hardware Design Example 4.6.1.1.2. Generating the Simulation Design Example
4.6.1.2. Dynamic Reconfiguration Design Examples x
4.6.1.2.1. Dynamic Reconfiguration Using Finite State Machine
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices x
5.1. Release Information 5.2. Functional Description 5.3. Getting Started 5.4. I/O Standards 5.5. Design Guidelines 5.6. Design Example 5.7. Application Specific Design Example
5.2. Functional Description x
5.2.1. Top Level Interfaces 5.2.2. Clocks 5.2.3. Output Path 5.2.4. Input Path 5.2.5. Dynamic Reconfiguration
5.2.2. Clocks x
5.2.2.1. Clock Frequency Relationships
5.2.3. Output Path x
5.2.3.1. Output Path Data Alignment
5.2.4. Input Path x
5.2.4.1. Input Path Data Alignment
5.2.5. Dynamic Reconfiguration x
5.2.5.1. RTL Connectivity 5.2.5.2. Address Lookup 5.2.5.3. Reconfiguration Features and Register Addressing 5.2.5.4. Calibration Guidelines
5.2.5.1. RTL Connectivity x
5.2.5.1.1. Daisy Chain
5.2.5.2. Address Lookup x
5.2.5.2.1. Strobes 5.2.5.2.2. Parameter Table Examples
5.2.5.3. Reconfiguration Features and Register Addressing x
5.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Address Registers 5.2.5.3.2. Control Registers Description
5.2.5.4. Calibration Guidelines x
5.2.5.4.1. Strobe Enable Window Calibration 5.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
5.3. Getting Started x
5.3.1. Parameter Settings 5.3.2. Signals
5.3.1. Parameter Settings x
5.3.1.1. Read Latency 5.3.1.2. Write Latency
5.3.2. Signals x
5.3.2.1. Clock and Reset Interface Signals 5.3.2.2. Output Path Signals 5.3.2.3. Input Path Signals 5.3.2.4. Avalon Configuration Bus Interface Signals 5.3.2.5. Termination Signals
5.4. I/O Standards x
5.4.1. Input Buffer Reference Voltage (VREF) 5.4.2. On-Chip Termination (OCT)
5.4.1. Input Buffer Reference Voltage (VREF) x
5.4.1.1. Calibrated VREF Settings
5.4.2. On-Chip Termination (OCT) x
5.4.2.1. RZQ_GROUP Assignment 5.4.2.2. Manual Insertion of OCT Block
5.5. Design Guidelines x
5.5.1. Guidelines: Group Pin Placement 5.5.2. Reference Clock 5.5.3. Reset 5.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 5.5.5. Dynamic Reconfiguration 5.5.6. Timing
5.5.6. Timing x
5.5.6.1. Timing Components 5.5.6.2. Timing Constraints and Files 5.5.6.3. Timing Analysis 5.5.6.4. Timing Closure Guidelines
5.5.6.2. Timing Constraints and Files x
5.5.6.2.1. <variation_name>.sdc 5.5.6.2.2. <variation_name>_parameter.tcl 5.5.6.2.3. <variation_name>_ip_parameters.tcl 5.5.6.2.4. <variation_name>_pin_map.tcl 5.5.6.2.5. <variation_name>_report_timing.tcl 5.5.6.2.6. <variation_name>_report_timing_core.tcl
5.5.6.4. Timing Closure Guidelines x
5.5.6.4.1. Timing Closure: Dynamic Reconfiguration 5.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 5.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 5.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 5.5.6.4.5. I/O Timing Violation 5.5.6.4.6. Internal FPGA Path Timing Violation
5.6. Design Example x
5.6.1. Generating the Design Example
5.6.1. Generating the Design Example x
5.6.1.1. Design Example without Dynamic Reconfiguration 5.6.1.2. Dynamic Reconfiguration Design Examples
5.6.1.1. Design Example without Dynamic Reconfiguration x
5.6.1.1.1. Generating the Hardware Design Example 5.6.1.1.2. Generating the Simulation Design Example
5.6.1.2. Dynamic Reconfiguration Design Examples x
5.6.1.2.1. Dynamic Reconfiguration with Debug Kit 5.6.1.2.2. Dynamic Reconfiguration Using Finite State Machine
5.7. Application Specific Design Example x
5.7.1. Implementation using the PHY Lite for Parallel Interfaces Intel® FPGA IP
1. About the PHY Lite for Parallel Interfaces IP
2. PHY Lite for Parallel Interfaces Intel® FPGA IP (phylite_ph2) for Intel Agilex® 7 M-Series Devices
3. PHY Lite for Parallel Interfaces Intel® FPGA IP (altera_phylite_s20) for Intel Agilex® 7 F-Series and I-Series Devices
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices
6. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives
7. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

3.5.1. Guidelines: Group Pin Placement

Follow these guidelines to place the PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series devices group pins.
  1. All groups in a PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series devices must be placed across a contiguous set of lanes. The number of lanes depends on the number of pins used by the group. Refer to the Intel Agilex® 7 Input DQS Clock Tree for more information about the number lanes used per pin width.
  2. A PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series devices must fit within one I/O sub-bank and must not span across multiple I/O sub-banks. One I/O sub-bank can support only one IP instance.
  3. Two groups within a PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series devices cannot share an I/O lane.
  4. When there are multiple groups within an IP instance, the pins must be set to either bidirectional or unidirectional (can be a mix of input and output groups). Do not mix bidirectional and unidirectional pin types in the same IP instance.
  5. If an input group uses ×36 DQS/strobe tree, another group must be set as an output group to utilize the remainder I/O lane in the same I/O sub-bank.
  6. If a group is set to bidirectional pin type and uses the ×36 DQS/strobe tree, no other groups are allowed to be in the same IP.
  7. Control signals are shared across all groups within an IP instance.
  8. Pins that are not used in an I/O sub-bank cannot be used as GPIO pins.
  9. You must calibrate the I/Os within the same I/O lane using the same OCT calibration block. You can associate the terminated pins of the PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series devices instance with an RZQ pin through the RZQ_GROUP assignment.
  10. You can place the data pin locations either automatically or manually in the Pin Placement tab. You must enter your desired Physical Sub-Bank ID. Refer to diagrams in the Intel Agilex® 7 I/O Sub-bank Interconnects topic for the physical sub-bank ID for pin placement.
  11. The PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series devices must be placed at the Quartus-IP Generation stage because the pin placements are not available using QSF Assignments.
  12. If all the lanes in a sub-bank are not bonded out, make sure that all the PHY Lite pins are constrained. Otherwise, the design will fail at compilation.
Table 43.  Pin Index Mapping
I/O Bank Pin Index I/O Sub-bank Pin Index Lane Sub-bank Location
0-11 0-11 (pins 4 and 5 are reserved for strobes) 0 Bottom
12-23 12-23 (pins 16 and 17 are reserved for strobes) 1
24-35 24-35 (pins 28 and 29 are reserved for strobes) 2
36-47 36-47 (pins 40 and 41 are reserved for strobes) 3
48-59 0-11 (pins 4 and 5 are reserved for strobes) 0 Top
60-71 12-23 (pins 16 and 17 are reserved for strobes) 1
72-83 24-35 (pins 28 and 29 are reserved for strobes) 2
84-95 36-47 (pins 40 and 41 are reserved for strobes) 3

For more information about strobe and clock pin indexes, refer to the device pin-out files.

Automatic and Manual Pin Placement

Follow these guidelines for automatic and manual pin placements:

  1. Go to the Pin Placement tab.
  2. To identify the sub-bank:
    • Default value = 0.
    • Use only bonded sub-banks. The bonded sub-banks are unshaded in the Example of Pin Placement for a Single Group diagram.
    • This example uses sub-bank ID =1 that is located at Bank 3A.
    Figure 44. Example of Pin Placement for a Single Group

    This example uses the Intel Agilex® 7 AGF022 and AGF027 devices, package R25A.

  3. Each sub-bank has 48 pins.
  4. In automatic mode, by default, all pins inside a group are placed in a tightly packed manner.
  5. In manual mode, you can customize the pin placement within the sub-bank according to your requirement.
    • By default, all data pins are contiguous in sequential order.
    • For example, for a pin width of 8, data pins are assigned to Pin 0, 1, 2, and 3 in Lane 1 and Lane 2.
    • You can choose to specify the placements manually, by providing a comma-separated list of pin locations, one for each data pin in Pin Placement Settings.
    • The comma-separated list of pin locations is based on the index within an I/O sub-bank. Refer to the Pin Index Mapping table.
Figure 45. Example Settings for Automatic and Manual Pin Placement
Related Information
Level Two Title