PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

Download PDF
ID 683716
Date 1/12/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the PHY Lite for Parallel Interfaces IP 2. PHY Lite for Parallel Interfaces Intel® FPGA IP (phylite_ph2) for Intel Agilex® 7 M-Series Devices 3. PHY Lite for Parallel Interfaces Intel® FPGA IP (altera_phylite_s20) for Intel Agilex® 7 F-Series and I-Series Devices 4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices 5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices 6. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives 7. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide
1. About the PHY Lite for Parallel Interfaces IP x
1.1. Device Family Support 1.2. Features
2. PHY Lite for Parallel Interfaces Intel® FPGA IP (phylite_ph2) for Intel Agilex® 7 M-Series Devices x
2.1. Release Information 2.2. Functional Description 2.3. Getting Started 2.4. I/O Standards 2.5. Design Example
2.2. Functional Description x
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for M-Series Devices Top Level Interfaces 2.2.2. Dynamic Reconfiguration 2.2.3. I/O Timing
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for M-Series Devices Top Level Interfaces x
2.2.1.1. Clocks 2.2.1.2. Output Path 2.2.1.3. Input Path
2.2.1.1. Clocks x
2.2.1.1.1. Clock Frequency Relationships
2.2.2. Dynamic Reconfiguration x
2.2.2.1. Calibration IP 2.2.2.2. Dynamic Reconfigurable Delays 2.2.2.3. Register Map
2.3. Getting Started x
2.3.1. Parameter Settings 2.3.2. Signals
2.3.2. Signals x
2.3.2.1. Clock and Reset Interface Signals 2.3.2.2. Output Path Signals 2.3.2.3. Input Path Signals
2.4. I/O Standards x
2.4.1. Design Guidelines
2.4.1. Design Guidelines x
2.4.1.1. DQS Trees 2.4.1.2. Pin Placement Restrictions
2.5. Design Example x
2.5.1. Generating the Design Example 2.5.2. Verifying Simulation Design Examples using Tester IP
2.5.1. Generating the Design Example x
2.5.1.1. Design Example without Dynamic Reconfiguration 2.5.1.2. Dynamic Reconfiguration Design Examples
2.5.1.1. Design Example without Dynamic Reconfiguration x
2.5.1.1.1. Generating the Synthesis Design Example 2.5.1.1.2. Generating the Simulation Design Example
2.5.1.2. Dynamic Reconfiguration Design Examples x
2.5.1.2.1. Generating the Synthesis Design Example 2.5.1.2.2. Generating the Simulation Design Example
3. PHY Lite for Parallel Interfaces Intel® FPGA IP (altera_phylite_s20) for Intel Agilex® 7 F-Series and I-Series Devices x
3.1. Release Information 3.2. Functional Description 3.3. Getting Started 3.4. I/O Standards 3.5. Design Guidelines 3.6. Design Example
3.2. Functional Description x
3.2.1. Intel Agilex® 7 F-Series and I-Series I/O Sub-bank Interconnects 3.2.2. Intel Agilex® 7 F-Series and I-Series Input DQS/Strobe Tree 3.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series Devices Top Level Interfaces 3.2.4. Dynamic Reconfiguration 3.2.5. I/O Timing
3.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel Agilex® 7 F-Series and I-Series Devices Top Level Interfaces x
3.2.3.1. Clocks 3.2.3.2. Output Path 3.2.3.3. Input Path
3.2.3.1. Clocks x
3.2.3.1.1. Clock Frequency Relationships
3.2.4. Dynamic Reconfiguration x
3.2.4.1. Connectivity 3.2.4.2. Reconfiguration Features and Register Addressing 3.2.4.3. Dynamic Reconfiguration Guidelines
3.2.4.2. Reconfiguration Features and Register Addressing x
3.2.4.2.1. Control Registers Addresses 3.2.4.2.2. Control Registers
3.2.4.3. Dynamic Reconfiguration Guidelines x
3.2.4.3.1. Strobe Enable Window Calibration 3.2.4.3.2. Output and Strobe Enable Minimum and Maximum Phase Settings 3.2.4.3.3. Input DQ/DQS Delay Chains Maximum Values
3.3. Getting Started x
3.3.1. Parameter Settings 3.3.2. Signals
3.3.1. Parameter Settings x
3.3.1.1. Read Latency 3.3.1.2. Write Latency
3.3.2. Signals x
3.3.2.1. Clock and Reset Interface Signals 3.3.2.2. Output Path Signals 3.3.2.3. Input Path Signals
3.4. I/O Standards x
3.4.1. Input Buffer Reference Voltage (VREF) 3.4.2. On-Chip Termination (OCT)
3.4.2. On-Chip Termination (OCT) x
3.4.2.1. RZQ_GROUP Assignment
3.5. Design Guidelines x
3.5.1. Guidelines: Group Pin Placement 3.5.2. Reference Clock 3.5.3. Reset
3.6. Design Example x
3.6.1. Generating the Design Example
3.6.1. Generating the Design Example x
3.6.1.1. Design Example without Dynamic Reconfiguration 3.6.1.2. Dynamic Reconfiguration Design Examples
3.6.1.1. Design Example without Dynamic Reconfiguration x
3.6.1.1.1. Generating the Synthesis Design Example 3.6.1.1.2. Generating the Simulation Design Example
3.6.1.2. Dynamic Reconfiguration Design Examples x
3.6.1.2.1. Generating the Synthesis Design Example 3.6.1.2.2. Generating the Simulation Design Example
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices x
4.1. Release Information 4.2. Functional Description 4.3. Getting Started 4.4. I/O Standards 4.5. Design Guidelines 4.6. Design Example
4.2. Functional Description x
4.2.1. Top Level Interfaces 4.2.2. Clocks 4.2.3. Output Path 4.2.4. Input Path 4.2.5. Dynamic Reconfiguration
4.2.2. Clocks x
4.2.2.1. Clock Frequency Relationships
4.2.3. Output Path x
4.2.3.1. Output Path Data Alignment
4.2.4. Input Path x
4.2.4.1. Input Path Data Alignment
4.2.5. Dynamic Reconfiguration x
4.2.5.1. RTL Connectivity 4.2.5.2. Address Lookup 4.2.5.3. Reconfiguration Features and Register Addressing 4.2.5.4. Calibration Guidelines
4.2.5.1. RTL Connectivity x
4.2.5.1.1. Daisy Chain
4.2.5.2. Address Lookup x
4.2.5.2.1. Strobes 4.2.5.2.2. Parameter Table Examples
4.2.5.3. Reconfiguration Features and Register Addressing x
4.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices Control Registers Addresses 4.2.5.3.2. Control Registers Description
4.2.5.4. Calibration Guidelines x
4.2.5.4.1. Strobe Enable Window Calibration 4.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
4.3. Getting Started x
4.3.1. Parameter Settings 4.3.2. Signals
4.3.1. Parameter Settings x
4.3.1.1. Read Latency 4.3.1.2. Write Latency
4.3.2. Signals x
4.3.2.1. Clock and Reset Interface Signals 4.3.2.2. Output Path Signals 4.3.2.3. Input Path Signals 4.3.2.4. Avalon Configuration Bus Interface Signals 4.3.2.5. Termination Signals
4.4. I/O Standards x
4.4.1. Input Buffer Reference Voltage (VREF) 4.4.2. On-Chip Termination (OCT)
4.4.1. Input Buffer Reference Voltage (VREF) x
4.4.1.1. Calibrated VREF Settings
4.4.2. On-Chip Termination (OCT) x
4.4.2.1. RZQ_GROUP Assignment 4.4.2.2. Manual Insertion of OCT Block
4.5. Design Guidelines x
4.5.1. Guidelines: Group Pin Placement 4.5.2. Reference Clock 4.5.3. Reset 4.5.4. Constraining Multiple PHY Lite for Parallel Interfaces Intel® FPGA IP to One I/O Bank 4.5.5. Dynamic Reconfiguration 4.5.6. Timing
4.5.6. Timing x
4.5.6.1. Timing Components 4.5.6.2. Timing Constraints and Files 4.5.6.3. Timing Analysis 4.5.6.4. Timing Closure Guidelines
4.5.6.2. Timing Constraints and Files x
4.5.6.2.1. <variation_name>.sdc 4.5.6.2.2. <variation_name>_parameter.tcl 4.5.6.2.3. <variation_name>_ip_parameters.tcl 4.5.6.2.4. <variation_name>_pin_map.tcl 4.5.6.2.5. <variation_name>_report_timing.tcl 4.5.6.2.6. <variation_name>_report_timing_core.tcl
4.5.6.4. Timing Closure Guidelines x
4.5.6.4.1. Timing Closure: Dynamic Reconfiguration 4.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 4.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 4.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 4.5.6.4.5. I/O Timing Violation 4.5.6.4.6. Internal FPGA Path Timing Violation
4.6. Design Example x
4.6.1. Generating the Design Example
4.6.1. Generating the Design Example x
4.6.1.1. Design Example without Dynamic Reconfiguration 4.6.1.2. Dynamic Reconfiguration Design Examples
4.6.1.1. Design Example without Dynamic Reconfiguration x
4.6.1.1.1. Generating the Hardware Design Example 4.6.1.1.2. Generating the Simulation Design Example
4.6.1.2. Dynamic Reconfiguration Design Examples x
4.6.1.2.1. Dynamic Reconfiguration Using Finite State Machine
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices x
5.1. Release Information 5.2. Functional Description 5.3. Getting Started 5.4. I/O Standards 5.5. Design Guidelines 5.6. Design Example 5.7. Application Specific Design Example
5.2. Functional Description x
5.2.1. Top Level Interfaces 5.2.2. Clocks 5.2.3. Output Path 5.2.4. Input Path 5.2.5. Dynamic Reconfiguration
5.2.2. Clocks x
5.2.2.1. Clock Frequency Relationships
5.2.3. Output Path x
5.2.3.1. Output Path Data Alignment
5.2.4. Input Path x
5.2.4.1. Input Path Data Alignment
5.2.5. Dynamic Reconfiguration x
5.2.5.1. RTL Connectivity 5.2.5.2. Address Lookup 5.2.5.3. Reconfiguration Features and Register Addressing 5.2.5.4. Calibration Guidelines
5.2.5.1. RTL Connectivity x
5.2.5.1.1. Daisy Chain
5.2.5.2. Address Lookup x
5.2.5.2.1. Strobes 5.2.5.2.2. Parameter Table Examples
5.2.5.3. Reconfiguration Features and Register Addressing x
5.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Address Registers 5.2.5.3.2. Control Registers Description
5.2.5.4. Calibration Guidelines x
5.2.5.4.1. Strobe Enable Window Calibration 5.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
5.3. Getting Started x
5.3.1. Parameter Settings 5.3.2. Signals
5.3.1. Parameter Settings x
5.3.1.1. Read Latency 5.3.1.2. Write Latency
5.3.2. Signals x
5.3.2.1. Clock and Reset Interface Signals 5.3.2.2. Output Path Signals 5.3.2.3. Input Path Signals 5.3.2.4. Avalon Configuration Bus Interface Signals 5.3.2.5. Termination Signals
5.4. I/O Standards x
5.4.1. Input Buffer Reference Voltage (VREF) 5.4.2. On-Chip Termination (OCT)
5.4.1. Input Buffer Reference Voltage (VREF) x
5.4.1.1. Calibrated VREF Settings
5.4.2. On-Chip Termination (OCT) x
5.4.2.1. RZQ_GROUP Assignment 5.4.2.2. Manual Insertion of OCT Block
5.5. Design Guidelines x
5.5.1. Guidelines: Group Pin Placement 5.5.2. Reference Clock 5.5.3. Reset 5.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 5.5.5. Dynamic Reconfiguration 5.5.6. Timing
5.5.6. Timing x
5.5.6.1. Timing Components 5.5.6.2. Timing Constraints and Files 5.5.6.3. Timing Analysis 5.5.6.4. Timing Closure Guidelines
5.5.6.2. Timing Constraints and Files x
5.5.6.2.1. <variation_name>.sdc 5.5.6.2.2. <variation_name>_parameter.tcl 5.5.6.2.3. <variation_name>_ip_parameters.tcl 5.5.6.2.4. <variation_name>_pin_map.tcl 5.5.6.2.5. <variation_name>_report_timing.tcl 5.5.6.2.6. <variation_name>_report_timing_core.tcl
5.5.6.4. Timing Closure Guidelines x
5.5.6.4.1. Timing Closure: Dynamic Reconfiguration 5.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 5.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 5.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 5.5.6.4.5. I/O Timing Violation 5.5.6.4.6. Internal FPGA Path Timing Violation
5.6. Design Example x
5.6.1. Generating the Design Example
5.6.1. Generating the Design Example x
5.6.1.1. Design Example without Dynamic Reconfiguration 5.6.1.2. Dynamic Reconfiguration Design Examples
5.6.1.1. Design Example without Dynamic Reconfiguration x
5.6.1.1.1. Generating the Hardware Design Example 5.6.1.1.2. Generating the Simulation Design Example
5.6.1.2. Dynamic Reconfiguration Design Examples x
5.6.1.2.1. Dynamic Reconfiguration with Debug Kit 5.6.1.2.2. Dynamic Reconfiguration Using Finite State Machine
5.7. Application Specific Design Example x
5.7.1. Implementation using the PHY Lite for Parallel Interfaces Intel® FPGA IP
1. About the PHY Lite for Parallel Interfaces IP
2. PHY Lite for Parallel Interfaces Intel® FPGA IP (phylite_ph2) for Intel Agilex® 7 M-Series Devices
3. PHY Lite for Parallel Interfaces Intel® FPGA IP (altera_phylite_s20) for Intel Agilex® 7 F-Series and I-Series Devices
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Arria® 10 and Intel® Cyclone® 10 GX Devices
6. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives
7. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

4.4.2.2. Manual Insertion of OCT Block

You may also instantiate the OCT Intel® FPGA IP separately in your project and connect the termination ports to the PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 devices.

  1. Expose the PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 devices termination ports by disable Use Default OCT Values.
  2. Select the available OCT values in the Input OCT Value parameter. This displays the Expose termination ports parameter.
    Note: For supported input and output OCT values, refer to the I/O Standards topic.
  3. Select Expose termination ports to expose the termination ports in the IP.
  4. Connect the termination ports to a OCT Intel® FPGA IP either in power-up or user mode.
Figure 72. RTL View of PHY Lite for Parallel Interfaces Intel® FPGA IP for Intel® Stratix® 10 Devices Interfacing with OCT Intel® FPGA IP in User Mode
Related Information
Level Two Title