Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon® Memory-Mapped (Avalon-MM) DMA Interface for PCI Express* Solutions User Guide

Download PDF
ID 683425
Date 6/03/2021
Public
Document Table of Contents
Document Table of Contents x
1. Datasheet 2. Getting Started with the Avalon-MM DMA 3. Parameter Settings 4. Physical Layout 5. Registers 6. Error Handling 7. PCI Express Protocol Stack 8. Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon-MM DMA for PCI Express 9. Design Implementation A. Transaction Layer Packet (TLP) Header Formats B. Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon-MM DMA Interface for PCIe Solutions User Guide Archive C. Document Revision History
1. Datasheet x
1.1. Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon-MM DMA Interface for PCIe* Datasheet 1.2. Features 1.3. Comparison of Avalon-ST, Avalon-MM and Avalon-MM with DMA Interfaces 1.4. Release Information 1.5. Device Family Support 1.6. Design Examples 1.7. IP Core Verification 1.8. Resource Utilization 1.9. Recommended Speed Grades 1.10. Creating a Design for PCI Express
1.7. IP Core Verification x
1.7.1. Compatibility Testing Environment
2. Getting Started with the Avalon-MM DMA x
2.1. Understanding the Avalon-MM DMA Ports 2.2. Generating the Testbench 2.3. Simulating the Example Design in ModelSim* 2.4. Running a Gate-Level Simulation 2.5. Generating Synthesis Files 2.6. Compiling the Design 2.7. Creating a Quartus® Prime Project
2.2. Generating the Testbench x
2.2.1. Understanding the Simulation Generated Files 2.2.2. Understanding Simulation Log File Generation
3. Parameter Settings x
3.1. Parameters 3.2. Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon-MM Settings 3.3. Base Address Register (BAR) Settings 3.4. Device Identification Registers 3.5. PCI Express and PCI Capabilities Parameters 3.6. Configuration, Debug, and Extension Options 3.7. PHY Characteristics 3.8. Example Designs
3.1. Parameters x
3.1.1. RX Buffer Allocation Selections Available by Interface Type
3.5. PCI Express and PCI Capabilities Parameters x
3.5.1. Device Capabilities 3.5.2. Error Reporting 3.5.3. Link Capabilities 3.5.4. MSI and MSI-X Capabilities 3.5.5. Slot Capabilities 3.5.6. Power Management 3.5.7. Vendor Specific Extended Capability (VSEC)
4. Physical Layout x
4.1. Hard IP Block Placement In Intel® Cyclone® 10 GX Devices 4.2. Hard IP Block Placement In Intel® Arria® 10 Devices 4.3. Channel and Pin Placement for the Gen1, Gen2, and Gen3 Data Rates 4.4. Channel Placement and fPLL and ATX PLL Usage for the Gen3 Data Rate 4.5. PCI Express Gen3 Bank Usage Restrictions
5. Registers x
5.1. Correspondence between Configuration Space Registers and the PCIe Specification 5.2. Type 0 Configuration Space Registers 5.3. Type 1 Configuration Space Registers 5.4. PCI Express Capability Structures 5.5. Intel-Defined VSEC Registers 5.6. Advanced Error Reporting Capability 5.7. DMA Descriptor Controller Registers 5.8. Control Register Access (CRA) Avalon-MM Slave Port
5.5. Intel-Defined VSEC Registers x
5.5.1. CvP Registers
5.6. Advanced Error Reporting Capability x
5.6.1. Uncorrectable Internal Error Mask Register 5.6.2. Uncorrectable Internal Error Status Register 5.6.3. Correctable Internal Error Mask Register 5.6.4. Correctable Internal Error Status Register
5.7. DMA Descriptor Controller Registers x
5.7.1. Read DMA Descriptor Controller Registers 5.7.2. Write DMA Descriptor Controller Registers 5.7.3. Read DMA and Write DMA Descriptor Format 5.7.4. Read DMA Example 5.7.5. Software Program for Simultaneous Read and Write DMA
6. Error Handling x
6.1. Physical Layer Errors 6.2. Data Link Layer Errors 6.3. Transaction Layer Errors 6.4. Error Reporting and Data Poisoning 6.5. Uncorrectable and Correctable Error Status Bits
7. PCI Express Protocol Stack x
7.1. Top-Level Interfaces 7.2. Data Link Layer 7.3. Physical Layer
7.1. Top-Level Interfaces x
7.1.1. Avalon-MM DMA Interface 7.1.2. Clocks and Reset 7.1.3. Interrupts 7.1.4. PIPE
8. Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon-MM DMA for PCI Express x
8.1. Understanding the Internal DMA Descriptor Controller 8.2. Understanding the External DMA Descriptor Controller
9. Design Implementation x
9.1. Making Pin Assignments to Assign I/O Standard to Serial Data Pins 9.2. Recommended Reset Sequence to Avoid Link Training Issues 9.3. SDC Timing Constraints 9.4. Warnings Encountered When Using Narrow Avalon-MM Interfaces
A. Transaction Layer Packet (TLP) Header Formats x
A.1. TLP Packet Formats without Data Payload A.2. TLP Packet Formats with Data Payload
C. Document Revision History x
C.1. Document Revision History for the Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon® Memory Mapped (Avalon-MM) DMA Interface for PCIe* Solutions User Guide
1. Datasheet
2. Getting Started with the Avalon-MM DMA
3. Parameter Settings
4. Physical Layout
5. Registers
6. Error Handling
7. PCI Express Protocol Stack
8. Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon-MM DMA for PCI Express
9. Design Implementation
A. Transaction Layer Packet (TLP) Header Formats
B. Intel® Arria® 10 or Intel® Cyclone® 10 GX Avalon-MM DMA Interface for PCIe Solutions User Guide Archive
C. Document Revision History

5.7.2. Write DMA Descriptor Controller Registers

The following table describes the registers in the internal DMA Descriptor Controller. When the DMA Descriptor Controller is externally instantiated, these registers are accessed through a BAR. The offsets must be added to the base address for the write controller. When the Descriptor Controller is internally instantiated these registers are accessed through BAR0. The write controller is at offset 0x0100.

Address Offset

Register

Access

Description

0x0100

RC Write Status and Descriptor Base (Low)

R/W

Specifies the lower 32-bits of the base address of the write status and descriptor table in the Root Complex memory. This address must be on a 32-byte boundary. Software must program this register after programming the upper 32-bit register at offset 0x104. To change the RC Write Status and Descriptor Base (Low) base address, all descriptors specified by the WR_TABLE_SIZE must be exhausted.

0x0104

RC Write Status and Descriptor Base (High)

R/W

Specifies the upper 32-bits of the base address of the write status and descriptor table in the Root Complex memory. Software must program this register before programming the lower 32-bit register at offset 0x100.

0x0108

EP Write Status and Descriptor FIFO Base (Low)

RW

Specifies the lower 32 bits of the base address of the write descriptor table in Endpoint memory. The Write Descriptor Controller requests descriptors from Root Complex memory and writes the descriptors to this location. The address is the Avalon-MM address of the Descriptor Controller's Write Descriptor Table Avalon-MM Slave Port as seen by the Read DMA Avalon-MM Master Port. Software must program this register after programming the upper 32-bit register at offset 0x10C.

0x010C

EP Write Status and Descriptor FIFO Base (High)

RW

Specifies the upper 32 bits of the base address of the write descriptor table in Endpoint memory. The read DMA fetches the table from Root Complex memory and writes the table to this location. Software must program this register before programming the lower 32-bit register at offset 0x108.

0x0110

WR_DMA_LAST_PTR

RW

When read, returns the ID of the last descriptor requested. If no DMA request is outstanding or the DMA is in reset, returns a value 0xFF.

When written, specifies the ID of the last descriptor requested. The difference between the value read and the value written is the number of descriptors to be processed.

For example, if the value reads 4, the last descriptor requested is 4. To specify 5 more descriptors, software should write a 9 into the RD_DMA_LAST_PTR register. The DMA executes 5 more descriptors.

To have the write DMA record the done bit of every descriptor, program this register to transfer one descriptor at a time.

The Descriptor ID loops back to 0 after reaching WR_TABLE_SIZE.

For example, if the WR_DMA_LAST_PTR value read is 126 and you want to execute three more descriptors, software must write 127, and then 1 into the WR_DMA_LAST_PTR register.

0x0114 WR_TABLE_SIZE

RW

Specifies the size of the Read descriptor table. Set to the number of descriptors - 1. By default, WR_TABLE_SIZE is set to 127. This value specifies the last Descriptor ID. To change the RC Write Status and Descriptor Base (Low) base address, all descriptors specified by the WR_TABLE_SIZE must be exhausted.
0x0118 WR_CONTROL

RW

[31:1] Reserved.

[0]Done. When set, the Descriptor Controller writes the Done bit for each descriptor in the status table. The Descriptor Controller sends a single MSI interrupt after the final descriptor completes. When not set the Descriptor Controller generates Done for the final descriptor, as specified by WR_DMA_LAST_PTR. In both cases, the Descriptor Controller sends an MSI to the host after the completion of the last descriptor along with the status update for the last descriptor.

Level Two Title