LVDS Tunneling Protocol and Interface (LTPI) IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs

Download PDF
ID 844310
Date 8/15/2025
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Configuring and Generating the IP 3. Simulating the IP 4. Validating the IP 5. Troubleshooting and Debugging Issues 6. Appendix A: Functional Description 7. Appendix B: Registers 8. Document Revision History for the LVDS Tunneling Protocol and Interface (LTPI) IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs
1. Overview x
1.1. About the LVDS Tunneling Protocol and Interface (LTPI) IP 1.2. About the Document 1.3. Applicable Applications 1.4. Key Concepts 1.5. IP Design Flow 1.6. Design Considerations/Guidelines
1.1. About the LVDS Tunneling Protocol and Interface (LTPI) IP x
1.1.1. IP Release Information 1.1.2. IP Features 1.1.3. IP High-level Block Diagram 1.1.4. Licensing the IP 1.1.5. Device Family Support 1.1.6. Device Speed Grade Support 1.1.7. IP Core Support Levels 1.1.8. IP Performance and Resource Utilization
1.2. About the Document x
1.2.1. Target Audience 1.2.2. Conventions Used in the Document 1.2.3. Acronyms 1.2.4. Reference Documents and Training
1.4. Key Concepts x
1.4.1. Interface Tunneling Principle 1.4.2. LTPI Tunneling Methodology 1.4.3. Clock Topology 1.4.4. LTPI Frame 1.4.5. System-level Block Diagram 1.4.6. Link Management 1.4.7. Signal Description
1.4.4. LTPI Frame x
1.4.4.1. Link Detect and Link Speed Selection Frames 1.4.4.2. Link Detect Frame 1.4.4.3. Link Speed Frame 1.4.4.4. Advertise, Configure, and Accept Frames 1.4.4.5. Advertise Frames 1.4.4.6. Configure Frame 1.4.4.7. Accept Frame 1.4.4.8. LTPI Operational Frames 1.4.4.9. Default I/O Frame 1.4.4.10. Default Data Frame
1.4.6. Link Management x
1.4.6.1. Link Training 1.4.6.2. Link Configuration 1.4.6.3. Operational Mode
1.4.7. Signal Description x
1.4.7.1. Clock and Power Signals 1.4.7.2. Channel Signals 1.4.7.3. Avalon® Memory-Mapped Primary Interface Signals 1.4.7.4. Avalon® Memory-Mapped Secondary Interface Signals 1.4.7.5. Avalon® Memory-Mapped CSR Interface Signals 1.4.7.6. Miscellaneous Interface Signals
2. Configuring and Generating the IP x
2.1. Configuring the Quartus® Prime Pro Edition Project 2.2. Configuring the LVDS Tunneling Protocol and Interface (LTPI) IP 2.3. Generating HDL for Synthesis and Simulation 2.4. Generating the Simulation Design Example
2.2. Configuring the LVDS Tunneling Protocol and Interface (LTPI) IP x
2.2.1. Configuring the LVDS Tunneling Protocol and Interface (LTPI) IP Parameters
2.3. Generating HDL for Synthesis and Simulation x
2.3.1. Generated File Structure
2.4. Generating the Simulation Design Example x
2.4.1. Generated Directory Structure and Files
3. Simulating the IP x
3.1. Design Example Features 3.2. Design Example Components 3.3. Configuring the Design Example Parameters 3.4. Simulating the Design Example
3.4. Simulating the Design Example x
3.4.1. Simulation Testbench Flow 3.4.2. Simulation Output
4. Validating the IP x
4.1. Validating the IP Using Agilex™ 5 Device
4.1. Validating the IP Using Agilex™ 5 Device x
4.1.1. Compiling the Design Example in Hardware on Agilex™ 5 Device 4.1.2. Validating the Design Example in Hardware on Agilex™ 5 Device
4.1.2. Validating the Design Example in Hardware on Agilex™ 5 Device x
4.1.2.1. Configuring the Clocks in Hardware 4.1.2.2. Programming the FPGA 4.1.2.3. Running the Hardware Test
6. Appendix A: Functional Description x
6.1. GPIO Channel 6.2. I2C Channel 6.3. UART Channel 6.4. Data Channel 6.5. OEM Channel
1. Overview
2. Configuring and Generating the IP
3. Simulating the IP
4. Validating the IP
5. Troubleshooting and Debugging Issues
6. Appendix A: Functional Description
7. Appendix B: Registers
8. Document Revision History for the LVDS Tunneling Protocol and Interface (LTPI) IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs and SoCs

1.4.4.2. Link Detect Frame

The link detect frame is used to exchange information about the LTPI version and operating speed capabilities to determine the common target speed between SCM and HPM.

Speed capabilities are defined as multiples of a base frequency of 25 MHz in a single data rate (SDR) mode. The highest bit indicates that the dual data rate (DDR) is supported at target link speed if its bit is set to 1. LTPI can support various speed combinations, but all must support the base 25 MHz frequency. The following table defines the speed capabilities.

Table 15.  Speed Capabilities Encoding
Byte Bit Field Encoding
7 6 5 4 3 2 1 0
0 Reserved

Base Frequency x10

250 MHz

Base Frequency x8

200 MHz

Base Frequency x6

150 MHz

Base Frequency x4

100 MHz

Base Frequency x3

75 MHz

Base Frequency x2

50 MHz

Base Frequency x1

25 MHz
1

Dual Data Rate

0: SDR

1: DDR

 Reserved Reserved Reserved Reserved Reserved Reserved Reserved

The link detect frame consists of LTPI version and speed capabilities of the LTPI IP. It is also used to automatically determine the common target speed between SCM and HPM.

Table 16.  Link Detect Frame

Frame Offset

(bytes)

Size

(bits)

 Bit Field Description
7 6 5 4 3 2 1 0  
0 8 Comma Symbol Comma symbol as defined in the Frame Type and Frame Subtype table.
1 8 Frame Subtype Frame subtype as defined in the Frame Type and Frame Subtype table.
2 8 LTPI Version Major LTPI Version Minor BCD Encoded LTPI Version (Major and minor LTPI version numbers).
3 8 Speed Capabilities Speed capabilities as defined in the Speed Capabilities Encoding table.
4 8 Reserved Reserved
5 8 Reserved Reserved
6 8 Reserved Reserved
7 8 Reserved Reserved
8 8 Reserved Reserved
9 8 Reserved Reserved
10 8 Reserved Reserved
11 8 Reserved Reserved
12 8 Reserved Reserved
13 8 Reserved Reserved
14 8 Reserved Reserved
15 8 CRC CRC8 checksum
Level Two Title