Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices

Download PDF
ID 683675
Date 4/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 50G Ethernet IP Core 2. Getting Started 3. Low Latency 50G Ethernet Intel® FPGA IP Parameters 4. Functional Description 5. Interfaces and Signal Descriptions 6. IP Core Register Descriptions 7. Document Revision History for the Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices
1. About the Low Latency 50G Ethernet IP Core x
1.1. Release Information 1.2. Supported Features 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. IP Core Verification 1.6. Performance and Resource Utilization
1.5. IP Core Verification x
1.5.1. Simulation Environment 1.5.2. Compilation Checking 1.5.3. Hardware Testing
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the Low Latency 50G Ethernet IP Core Parameters and Options 2.3. Simulating the IP Core 2.4. Generated File Structure 2.5. Integrating Your IP Core in Your Design 2.6. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating Your IP Core in Your Design x
2.5.1. Pin Assignments 2.5.2. Adding the Transceiver PLL 2.5.3. Placement Settings for the Low Latency 50G Ethernet IP Core
4. Functional Description x
4.1. TX MAC Datapath 4.2. TX PCS 4.3. RX MAC Datapath 4.4. RX PCS 4.5. Link Fault Signaling Interface 4.6. User Interface to Ethernet Transmission 4.7. Auto Negotiation and Link Training 4.8. Flow Control 4.9. Reset
4.1. TX MAC Datapath x
4.1.1. Frame Padding 4.1.2. Preamble Insertion 4.1.3. Inter-Packet Gap Generation and Insertion
4.3. RX MAC Datapath x
4.3.1. IP Core Preamble Processing 4.3.2. IP Core Strict SFD Checking 4.3.3. IP Core Malformed Packet Handling 4.3.4. Length/Type Field Processing 4.3.5. RX CRC Checking and Dynamic Forwarding
4.3.4. Length/Type Field Processing x
4.3.4.1. Length Checking
4.6. User Interface to Ethernet Transmission x
4.6.1. Order of Transmission 4.6.2. Bit Order For TX and RX Datapaths
4.8. Flow Control x
4.8.1. TX Pause/PFC Flow Control Transmission 4.8.2. XON/XOFF Pause Frames
5. Interfaces and Signal Descriptions x
5.1. TX MAC Interface to User Logic 5.2. RX MAC Interface to User Logic 5.3. Transceivers 5.4. Transceiver Reconfiguration Signals 5.5. Avalon® Memory-Mapped Management Interface 5.6. Miscellaneous Status and Debug Signals 5.7. Reset Signals 5.8. Flow Control Interface
5.4. Transceiver Reconfiguration Signals x
5.4.1. Disabling Background Calibration
6. IP Core Register Descriptions x
6.1. PHY Registers 6.2. TX MAC Registers 6.3. RX MAC Registers 6.4. Flow Control Registers 6.5. Statistics Registers 6.6. Auto-Negotiation and Link Training Registers
6.5. Statistics Registers x
6.5.1. TX Statistics Registers 6.5.2. RX Statistics Registers
6.6. Auto-Negotiation and Link Training Registers x
6.6.1. AN/LT Sequencer Config 6.6.2. AN/LT Sequencer Status 6.6.3. Auto Negotiation Config Register 1 6.6.4. Auto Negotiation Config Register 2 6.6.5. Auto Negotiation Status Register 6.6.6. Auto Negotiation Config Register 3 6.6.7. Auto Negotiation Config Register 4 6.6.8. Auto Negotiation Config Register 5 6.6.9. Auto Negotiation Config Register 6 6.6.10. Auto Negotiation Status Register 1 6.6.11. Auto Negotiation Status Register 2 6.6.12. Auto Negotiation Status Register 3 6.6.13. Auto Negotiation Status Register 4 6.6.14. Auto Negotiation Status Register 5 6.6.15. Link Training Config Register 1 6.6.16. Link Training Config Register 2 6.6.17. Link Training Status Register 1 6.6.18. Link Training Config Register for Lane 0 6.6.19. Link Training Frame Contents for Lane 0 6.6.20. Local Transceiver TX EQ 1 Settings for Lane 0 6.6.21. Local Transceiver TX EQ 2 Settings for Lane 0 6.6.22. Local Link Training Parameters 6.6.23. Link Training Config Register for Lane 1 6.6.24. Link Training Frame Contents for Lane 1 6.6.25. Local Transceiver TX EQ 1 Settings for Lane 1 6.6.26. Local Transceiver TX EQ 2 Settings for Lane 1 6.6.27. Link Training Config Register for Lane 2 6.6.28. Link Training Frame Contents for Lane 2 6.6.29. Local Transceiver TX EQ 1 Settings for Lane 2 6.6.30. Local Transceiver TX EQ 2 Settings for Lane 2 6.6.31. Link Training Config Register for Lane 3 6.6.32. Link Training Frame Contents for Lane 3 6.6.33. Local Transceiver TX EQ 1 Settings for Lane 3 6.6.34. Local Transceiver TX EQ 2 Settings for Lane 3
1. About the Low Latency 50G Ethernet IP Core
2. Getting Started
3. Low Latency 50G Ethernet Intel® FPGA IP Parameters
4. Functional Description
5. Interfaces and Signal Descriptions
6. IP Core Register Descriptions
7. Document Revision History for the Low Latency 50G Ethernet Intel® FPGA IP User Guide: Stratix® 10 Devices

4.3.4. Length/Type Field Processing

This two-byte header represents either the length of the payload or the type of MAC frame.
  • Length/type < 0x600—The field represents the payload length of a basic Ethernet frame. The MAC RX continues to check the frame and payload lengths.
  • Length/type >= 0x600—The field represents the frame type. The following frame types are possible:
    • Length/type = 0x8100—VLAN or stacked VLAN tagged frames (up to a total of two tags with value 0x8100). The MAC RX continues to check the frame and payload lengths.
    • Length/type = 0x8808—Control frames. The next two bytes are the Opcode field that indicates the type of control frame. For pause frames (Opcode = 0x0001) and PFC frames (Opcode = 0x0101), the MAC RX proceeds with pause frame processing. In addition to processing any pause request, the IP core passes these frames to the RX client interface and updates the appropriate l1_rxstatus_data bits.
    • For other field values, the MAC RX forwards the receive frame to the client.

Section Content
Length Checking

Level Two Title