AN 307: Intel® FPGA Design Flow for AMD* Xilinx* Users

Download PDF
ID 683562
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. Introduction to Intel® FPGA Design Flow for AMD* Xilinx* Users 2. Technology Comparison 3. FPGA Tools Comparison 4. AMD* Xilinx* to Intel® FPGA Design Conversion 5. Conclusion 6. AN 307: Intel® FPGA Design Flow for AMD* Xilinx* Users Archives 7. Document Revision History for Intel® FPGA Design Flow for AMD* Xilinx* Users
2. Technology Comparison x
2.1. Intel® FPGA and SoC Devices 2.2. Intel® - AMD* Xilinx* Device Comparison 2.3. Intel® FPGA Device Features
3. FPGA Tools Comparison x
3.1. Hardware and Software Tools for FPGA Design 3.2. FPGA Design Flow Using Command Line Scripting 3.3. FPGA Design Flow Using Tools with GUIs 3.4. Additional Quartus® Prime Pro Edition Features
3.2. FPGA Design Flow Using Command Line Scripting x
3.2.1. Command-Line Executable Equivalents 3.2.2. Programming and Configuration File Support in the Quartus® Prime Pro Edition Software
3.2.1. Command-Line Executable Equivalents x
3.2.1.1. synth_design 3.2.1.2. place_design/route_design 3.2.1.3. report_timing 3.2.1.4. write_bitstream 3.2.1.5. write_sdf/write_verilog/write_vhdl 3.2.1.6. report_power 3.2.1.7. write_checkpoint 3.2.1.8. Run Complete Design Flow
3.3. FPGA Design Flow Using Tools with GUIs x
3.3.1. Project Creation 3.3.2. Design Entry 3.3.3. IP Status 3.3.4. Design Constraints 3.3.5. Synthesis 3.3.6. Design Implementation 3.3.7. Finalize Pinout 3.3.8. Viewing and Editing Design Placement 3.3.9. Static Timing Analysis 3.3.10. Generation of Device Programming Files 3.3.11. Power Analysis 3.3.12. Simulation 3.3.13. Hardware Verification 3.3.14. View Netlist 3.3.15. Design Optimization 3.3.16. Techniques to Improve Productivity 3.3.17. Partial Reconfiguration 3.3.18. Cross-Probing in the Quartus® Prime Pro Edition Software
3.3.2. Design Entry x
3.3.2.1. HDL Editor 3.3.2.2. Schematic/Block Editor 3.3.2.3. State Machine Editor 3.3.2.4. IP Catalog and Parameter Editor 3.3.2.5. Platform Designer System Integration Tool 3.3.2.6. Platform Designer Component Editor
3.3.4. Design Constraints x
3.3.4.1. Assignment Editor 3.3.4.2. Create Timing Constraints with the Timing Analyzer GUI 3.3.4.3. Create Timing Constraints with the Timing Analyzer Text Editor
3.3.7. Finalize Pinout x
3.3.7.1. Pin Planner 3.3.7.2. Interface Planner 3.3.7.3. Tile Interface Planner
3.3.12. Simulation x
3.3.12.1. Simulation Models for Designs Containing LPMs or IP Cores
3.3.13. Hardware Verification x
3.3.13.1. System Console 3.3.13.2. Signal Tap Logic Analyzer 3.3.13.3. In-System Sources and Probes 3.3.13.4. Toolkit Explorer 3.3.13.5. Remote Debugging 3.3.13.6. Other Intel® FPGA Debugging Tools
3.3.13.4. Toolkit Explorer x
3.3.13.4.1. Transceiver Toolkit 3.3.13.4.2. EMIF Debug Toolkit
3.3.14. View Netlist x
3.3.14.1. RTL Viewer 3.3.14.2. Technology Map Viewer
3.3.15. Design Optimization x
3.3.15.1. Hyper-Aware Design Flow 3.3.15.2. Physical Synthesis Optimization 3.3.15.3. Optimization Modes 3.3.15.4. Fractal Synthesis
3.3.16. Techniques to Improve Productivity x
3.3.16.1. Fast Preservation 3.3.16.2. Engineering Change Order (ECO) Flow 3.3.16.3. Block-Based Design Flow 3.3.16.4. Design Assistant 3.3.16.5. Snapshot Viewer 3.3.16.6. Design Space Explorer II
3.4. Additional Quartus® Prime Pro Edition Features x
3.4.1. Scripting with Tcl in the Quartus® Prime Pro Edition Software
3.4.1. Scripting with Tcl in the Quartus® Prime Pro Edition Software x
3.4.1.1. Running Scripts from the DOS or UNIX Prompt 3.4.1.2. Running Scripts in Batch Mode from a Shell 3.4.1.3. Running Tcl Commands Directly from the Command Line 3.4.1.4. Running Tcl Commands Interactively from the Shell 3.4.1.5. The Quartus® Prime Tcl Console Window
4. AMD* Xilinx* to Intel® FPGA Design Conversion x
4.1. Replacing AMD* Xilinx* Primitives 4.2. Converting IP Cores 4.3. Setting Equivalent AMD* Xilinx* Design Constraints 4.4. Setting Up the Simulation Environment
4.1. Replacing AMD* Xilinx* Primitives x
4.1.1. Converting I/O Buffers 4.1.2. Changing Default I/O Standard for Pins 4.1.3. Converting Registers
4.1.1. Converting I/O Buffers x
4.1.1.1. Example of Converting I/O Buffer
4.2. Converting IP Cores x
4.2.1. Converting Memory Blocks 4.2.2. Converting Mixed-Mode Clock Manager (MMCM) to Phase-Locked Loop (PLL) 4.2.3. Converting Multipliers
4.2.1. Converting Memory Blocks x
4.2.1.1. Embedded Memory Blocks 4.2.1.2. Differences Between AMD* Xilinx* Memory and Intel® FPGA Memory 4.2.1.3. Determining Memory Block and Mapping Ports 4.2.1.4. Memory Port Mapping 4.2.1.5. Example: Converting Simple Dual-Port RAM
4.2.1.2. Differences Between AMD* Xilinx* Memory and Intel® FPGA Memory x
4.2.1.2.1. Memory Mode 4.2.1.2.2. Clocking Mode 4.2.1.2.3. Write and Read Operation Triggering 4.2.1.2.4. Read-During-Write Operation at the Same Address 4.2.1.2.5. Error Correction Code (ECC) 4.2.1.2.6. Byte Enable 4.2.1.2.7. Address Clock Enable 4.2.1.2.8. Parity Bit Support 4.2.1.2.9. Memory Initialization 4.2.1.2.10. Output Synchronous Set/Reset
4.2.2. Converting Mixed-Mode Clock Manager (MMCM) to Phase-Locked Loop (PLL) x
4.2.2.1. Feature Comparison 4.2.2.2. Port Mapping Reference 4.2.2.3. Example: Converting AMD* Xilinx* MMCM into an Intel® PLL
4.2.3. Converting Multipliers x
4.2.3.1. Feature Comparison 4.2.3.2. Port Mapping 4.2.3.3. Example: Converting to the LPM_MULT IP Core 4.2.3.4. Example: Converting to the Intel® FPGA Multiply Adder IP core
4.3. Setting Equivalent AMD* Xilinx* Design Constraints x
4.3.1. Device Constraints 4.3.2. Placement Constraints 4.3.3. Timing Constraints 4.3.4. Retimer Constraints
4.3.1. Device Constraints x
4.3.1.1. DRIVE 4.3.1.2. SLEW 4.3.1.3. IOB 4.3.1.4. IOSTANDARD 4.3.1.5. KEEP
4.3.2. Placement Constraints x
4.3.2.1. PBLOCK 4.3.2.2. PACKAGE_PIN 4.3.2.3. LOC & BEL 4.3.2.4. PROHIBIT
4.3.2.1. PBLOCK x
4.3.2.1.1. Differences Between PBLOCK and Logic Lock Regions
4.3.3. Timing Constraints x
4.3.3.1. Clock Domain Crossing
4.4. Setting Up the Simulation Environment x
4.4.1. Simulation Levels 4.4.2. HDL Support for EDA Simulators 4.4.3. Value Change Dump (VCD) Support 4.4.4. Simulating Intel FPGA IP Cores
1. Introduction to Intel® FPGA Design Flow for AMD* Xilinx* Users
2. Technology Comparison
3. FPGA Tools Comparison
4. AMD* Xilinx* to Intel® FPGA Design Conversion
5. Conclusion
6. AN 307: Intel® FPGA Design Flow for AMD* Xilinx* Users Archives
7. Document Revision History for Intel® FPGA Design Flow for AMD* Xilinx* Users

4.3.2.1. PBLOCK

Equivalent to the PBLOCK constraint in the AMD* Xilinx* Vivado* software, Logic Lock regions are floorplan location constraints in the Quartus® Prime Pro Edition software. Logic Lock region assignments have Placement and Routing Regions
The following example shows how to set a module's attributes in a XDC file, using:
  • EXCLUDE_PLACEMENT—directs the Fitter to place only pblock's logic in the device resources within the pblock region.
  • CONTAIN_ROUTING—directs the Fitter to route signals in the pblock area using only resources available within the pblock area.
In this example, the module does not contain any I/O resources.

XDC Command:

create_pblock pblock_uut_inst
add_cells_to_pblock [get_pblocks pblock_uut_inst] [get_cells -quiet [list uut_inst]]
resize_pblock [get_pblocks pblock_uut_inst] -add {SLICE_X218Y284:SLICE_X220Y346}
resize_pblock [get_pblocks pblock_uut_inst] -add {RAMB18_X12Y114:RAMB18_X12Y137}
resize_pblock [get_pblocks pblock_uut_inst] -add {RAMB36_X12Y57:RAMB36_X12Y68}
set_property CONTAIN_ROUTING 1 [get_pblocks pblock_uut_inst]
set_property EXCLUDE_PLACEMENT 1 [get_pblocks pblock_uut_inst]

Equivalent QSF Command:

set_instance_assignment -name PLACE_REGION "X1 Y1 X20 Y20" -to uut_inst
set_instance_assignment -name RESERVE_PLACE_REGION ON -to uut_inst
set_instance_assignment -name CORE_ONLY_PLACE_REGION ON -to uut_inst
set_instance_assignment -name REGION_NAME uut_inst -to uut_inst
set_instance_assignment -name ROUTE_REGION "X1 Y1 X20 Y20" -to uut_inst
REGION_NAME creates an Logic Lock region named “uut_inst”, and assigns module uut_inst to this region. This is similar to XDC's CREATE_PBLOCK and ADD_CELLS_TO_PBLOCK assignments. 
set_instance_assignment -name REGION_NAME uut_inst -to uut_inst
PLACE_REGION defines the coordinates for the placement region, similar to XDC's RESIZE_PBLOCK assignments. 
set_instance_assignment -name PLACE_REGION "X1 Y1 X20 Y20" -to uut_inst
RESERVE_PLACE_REGION prevents the Fitter from placing other logic in the region, equivalent to XDC's EXCLUDE_PLACEMENT assignment. 
set_instance_assignment -name RESERVE_PLACE_REGION ON -to uut_inst
Defining ROUTE_REGION with the same coordinates as PLACE_REGION indicates the routing to remain within the placement region, equivalent to XDC's CONTAIN_ROUTING assignment. 
set_instance_assignment -name ROUTE_REGION "X1 Y1 X20 Y20" -to uut_inst
By default, Logic Lock assignments include periphery resources, and you prevent this behavior with the CORE_ONLY_PLACE_REGION logic option. However, in XDC, the default behavior is to exclude periphery resources, so you must apply pblock constraints to include periphery resources in the pblock region. 
set_instance_assignment -name CORE_ONLY_PLACE_REGION ON -to uut_inst

Section Content
Differences Between PBLOCK and Logic Lock Regions

Related Information
Level Two Title