Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide

Download PDF
ID 683486
Date 4/09/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP 2. Low Latency E-Tile 40G Ethernet IP Core Parameters 3. Getting Started 4. Functional Description 5. Reset 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Debugging the Link 9. Ethernet Toolkit Overview 10. Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide Archives 11. Comparison Between Low Latency E-Tile 40G Ethernet Core and Low Latency 40GbE IP Core 12. Document Revision History for Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP x
1.1. Release Information 1.2. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Supported Features 1.3. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support 1.4. Resource Utilization
1.3. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support x
1.3.1. Device Family Support 1.3.2. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Speed Grade Support
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IP Cores 3.2. Specifying the Low Latency E-Tile 40G Ethernet IP Core Parameters and Options 3.3. Simulating the IP Core 3.4. Generated File Structure 3.5. Integrating Your IP Core in Your Design 3.6. Low Latency E-Tile 40G Ethernet IP Core Testbench 3.7. Compiling the Full Design and Programming the FPGA
3.5. Integrating Your IP Core in Your Design x
3.5.1. Pin Assignments 3.5.2. Ethernet Adaptation Flow 3.5.3. Placement Settings for the Low Latency E-Tile 40G Ethernet Core
3.6. Low Latency E-Tile 40G Ethernet IP Core Testbench x
3.6.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency E-Tile 40G Ethernet Core Functional Description 4.2. User Interface to Ethernet Transmission
4.1. Low Latency E-Tile 40G Ethernet Core Functional Description x
4.1.1. Low Latency E-Tile 40G Ethernet Core TX MAC Datapath 4.1.2. Low Latency E-Tile 40G Ethernet Core RX MAC Datapath 4.1.3. Link Fault Signaling Interface 4.1.4. Flow Control
4.1.1. Low Latency E-Tile 40G Ethernet Core TX MAC Datapath x
4.1.1.1. Frame Padding 4.1.1.2. Preamble Insertion 4.1.1.3. Inter-Packet Gap Generation and Insertion 4.1.1.4. Frame Check Sequence (CRC-32) Insertion
4.1.2. Low Latency E-Tile 40G Ethernet Core RX MAC Datapath x
4.1.2.1. IP Core Preamble Processing 4.1.2.2. IP Core Strict SFD Checking 4.1.2.3. Length/Type Field Processing 4.1.2.4. RX CRC Checking and Dynamic Forwarding
4.1.2.3. Length/Type Field Processing x
4.1.2.3.1. Length Checking
4.1.4. Flow Control x
4.1.4.1. TX Pause/PFC Flow Control Transmission 4.1.4.2. XON/XOFF Pause Frames
4.2. User Interface to Ethernet Transmission x
4.2.1. Order of Transmission 4.2.2. Bit Order For TX and RX Datapaths
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. Transceivers Signals 6.4. Transceiver Reconfiguration Signals 6.5. Avalon® Memory-Mapped Management Interface 6.6. Miscellaneous Status and Debug Signals 6.7. Reset Signals 6.8. Clocks 6.9. Flow Control Interface
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. TX MAC Registers 7.3. RX MAC Registers 7.4. Pause/PFC Flow Control Registers
9. Ethernet Toolkit Overview x
9.1. Features
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP
2. Low Latency E-Tile 40G Ethernet IP Core Parameters
3. Getting Started
4. Functional Description
5. Reset
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Debugging the Link
9. Ethernet Toolkit Overview
10. Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide Archives
11. Comparison Between Low Latency E-Tile 40G Ethernet Core and Low Latency 40GbE IP Core
12. Document Revision History for Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide

7.4. Pause/PFC Flow Control Registers

Some of the registers in this table cannot be updated during normal operation. To ensure correct operation, perform a soft reset by writing Bit[0] of the PHY_CONFIG (0x310) after updating registers that cannot be changed dynamically.
Table 27.  TX Flow Control Registers
Addr Bit Name Description Reset Access
0x600 31:0 TX Flow Control Revision ID

Specifies the revision ID, "100GFCTx CSR"

0x0809_20017

 RO
0x601 31:0 TX Flow Control Scratch Pad Scratch register for testing. 0 RW
0x602 31:0 TX Flow Control IP Core Variant 0

Specifies first 4 characters of IP core variation identifier ASCII string, "100G".

0x3130_3047

 RO
0x603 31:0 TX Flow Control IP Core Variant 1 Next 4 characters of IP core variation identifier ASCII string, "FCTx". 0x4643_5478 RO
0x604 31:0 TX Flow Control IP Core Variant 2

Final 4 characters of IP core variation identifier ASCII string, "xCSR".

0x0043_5352 RO
0x605

7:0

TX Flow Control Enable

One bit per queue

Enables the IP core to generate XON and XOFF Pause/PFC flow control frames to the remote partner. The following encodings are defined:
  • 1'b0: XON or XOFF Pause/PFC flow control is disabled.
  • 1'b1: XON or XOFF Pause/PFC flow control is enabled.

You can change this field dynamically.

0xFF

 RW

31:8

 Reserved Reserved 0 RO
0x606

7:0

TX Flow Control CSR XON/XOFF Request 0

XON/XOF flow control frame request bit 0. Interpretation depends on whether the IP core is in 1-bit FC request mode or in 2-bit FC request mode. This register affects a flow control queue only if the corresponding bit of the TX Flow Control Enable register has the value of 1.

In 2-bit mode, in addition, this register is active for a specific flow control queue only if the corresponding bit in the TX 2-bit Flow Control Request Mode register field (bits 7:0 of the register at offset 0x641) specifies that the flow control logic accepts input from this register.

The following encodings are defined for 1-bit mode. The IP core reads the 1-bit mode value in TX Flow Control CSR XON/XOFF Request 0.

  • 0 = No request
  • 0 to 1 = Generate XOFF request
  • 1 = Continue to generate XOFF request
  • 1 to 0 = Generate XON request

The following encodings are defined for 2-bit mode. The IP core reads the 2-bit mode value in {TX Flow Control CSR XON/XOFF Request 1, TX Flow Control CSR XON/XOFF Request 1}.

  • 00 = No request
  • 01 = XON request
  • 10 = XOFF request
  • 11 = Invalid

You can modify the value of this field dynamically.

0 RW

15:8

 Reserved Reserved 0 RO

23:16

TX Flow Control CSR XON/XOFF Request 1

In conjunction with Flow Control XON/XOFF Request 0 specifies a 2-bit request for XON/XOFF flow control frame transmission. This bit is the upper bit of the 2-bit control field.

You can change the value of this field dynamically.

0 RW

31:24

 Reserved Reserved 0 RO
0x60A 0

TX Pause Enable

1-bit

Determines whether receiving a valid Pause frame stops TX user data transmission.

1'b0: Transmission is not stopped

1'b1: Transmission stops

You cannot change the value of this field dynamically.

0 RW
31:1 Reserved Reserved 0 RO
0x60D 31:0 TX Flow Control Destination Address Lower

Specifies the 48-bit Destination Address of the flow control frame. Contains the 32 LSB of the address field.

You cannot modify the value of this field dynamically.

0xC2000001 RW
0x60E 15:0 TX Flow Control Destination Address Upper

Specifies the 48-bit Destination Address of flow control frame. Contains the 16 MSB of the address field.

You cannot modify the value of this field dynamically.

0x0180 RW
31:16 Reserved Reserved 0 RO
0x60F 31:0 TX Flow Control Source Address Lower

Specifies the 48-bit Source Address of flow control frame. Contains the 32 LSB of the address field.

0xCBFC5ADD RW
0x610 15:0 TX Flow Control Source Address Upper

Specifies the 48-bit Source Address of flow control frame. Contains the 16 MSB of the address field.

You cannot modify the value of this field dynamically.

0xE100 RW
31:16 Reserved Reserved 0 RO

0x620, 0x621, …, 0x620+(FCQN-1 where FCQN = 0 to 7)

15:0

TX Flow Control Quanta

16-bit per FCQN

Specifies the pause quanta of Pause/PFC flow control frames to be sent to remote partner.

You cannot modify the value of this field dynamically.

0xFFFF RW
31:16 Reserved Reserved 0 RO
0x628, 0x629, …, 0x628+(FCQN-1 where FCQN = 0 to 7) 15:0

TX Flow Control Signal XOFF Request Hold Quanta

16-bit per FCQN

Specifies the separation between 2 consecutive XOFF flow control frames.

You cannot modify the value of this field dynamically.

0xFFFF RW
31:16 Reserved Reserved 0 RO
0x640 0

TX Flow Control Select

1-bit

Specifies whether the TX hardware generates Pause or PFC frames. Affects only PFC Queue 0.

Usage example:

You can synthesize a single PFC queue and use it for both Pause and PFC purpose.

1'b0: Pause

1'b1: PFC

You cannot modify the value of this field dynamically.

1 RW
31:1 Reserved. Reserved. 0 RO
0x641 (FCQN-1):0

TX 2-bit Flow Control Request Mode

1-bit per FCQN

Determines whether the TX Flow Control CSR XON/XOFF Request register or the pause_insert_tx0 and pause_insert_tx1 signals control XON/XOFF mode in 2-bit control mode.

1'b0: The pause_insert_tx0 and pause_insert_tx1 signals control requests

1'b1: The TX Flow Control CSR XON/XOFF Request register fields control requests

You cannot modify the value of this field dynamically.

0 RW
16

TX Flow Control Request Mode

1 bit for all

FCQN

Determines whether the IP core is in TX flow control 1-bit mode or 2-bit mode.

1'b0: Use 1-bit mode to make TX flow control requests

1'b1: Use 2-bit mode to make TX flow control requests

0 RW
31:17 Reserved Reserved 0 RO
Table 28.  RX Flow Control Registers
Addr Bit Name Description Reset Access
0x700 31:0 RX Flow Control Revision ID

Specifies the revision ID, "100GFCTx CSR"

0x0809_20017

 RO
0x701 31:0 RX Flow Control Scratch Pad Provides a register for debug. 0 RW
0x702 31:0 RX Flow Control IP Core Variant 0

First 4 characters of IP core variation identifier ASCII string,

Specifies first 4 characters of IP core variation identifier ASCII string, "100G".

0x3130_3047

 RO
0x703 31:0 RX Flow Control IP Core Variant 1 Next 4 characters of IP core variation identifier ASCII string, "FCRx". 0x4643_5278 RO
0x704 31:0 RX Flow Control IP Core Variant 2 Final 4 characters of IP core variation identifier ASCII string, "0CSR". The "0" is unprintable. 0x0043_5352 RO
0x705 7:0

RX PFC Enable

1 bit per queue

Determines whether receiving a valid PFC frame causes the PFC duration user interface to indicate a valid pause quanta duration to the user logic.

1'b0: Disable

1'b1: Enable

You cannot modify the value of this field dynamically.

0xFF RW
31: 8 Reserved Reserved 0 RO
0x707 31:0 RX Flow Control Destination Address Lower

Specifies the 48-bit Destination Address of the flow control frame. Contains the 32 LSB of the address field.

The flow control frame is sent with the destination address matching the address specified in this register or the multicast address. If the address is not a match, the Flow Control block does not respond to the incoming frame; the IP core just passes it through.

You cannot modify the value of this field dynamically.

0xC2000001 RW
0x708 15:0 RX Flow Control Destination Address Upper

Specifies the 48-bit Destination Address of flow control frame. Contains the 16 MSB of the address field.

The flow control frame is sent with the destination address matching the address specified in this register or the multicast address. If the address is not a match, the Flow Control block does not respond to the incoming frame; the IP core just passes it through.

You cannot modify the value of this field dynamically.

0x0180 RW
31:16 Reserved Reserved 0 RO
Level Two Title