Agilex™ 3 FPGA and SoC C-Series Development Kit User Guide

Download PDF
ID 851698
Date 10/31/2025
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Agilex™ 3 FPGA and SoC C-Series Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Software and Driver Installation
2.2. Handling the Board x
2.2.1. Handling the DIP Switches
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Pro Edition Software 2.3.2. Installing the Ashling* RiscFree* Integrated Development Environment (IDE) 2.3.3. Installing the Development Kit 2.3.4. Installing the USB Blaster III Driver
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Board 3.3. Modes of Operations 3.4. Performing Board Restore
3.4. Performing Board Restore x
3.4.1. Restoring Board QSPI Flash U51 with Default Factory Image on Agilex™ 3 FPGA C-Series Development Kit 3.4.2. Restoring Board QSPI Flash U51 with Default Factory Image on Agilex™ 3 FPGA and SoC C-Series Development Kit 3.4.3. Restoring SD Card with Default Factory Image on Agilex™ 3 FPGA and SoC C-Series Development Kit
4. Board Test System x
4.1. Set Up the BTS GUI Running Environment 4.2. BTS Functionalities
4.1. Set Up the BTS GUI Running Environment x
4.1.1. Setting Up the Quartus® Prime Software for BTS Operation 4.1.2. Running the BTS GUI
4.2. BTS Functionalities x
4.2.1. The Agilex™ 3 FPGA Functionality 4.2.2. Other Functionalities
4.2.1. The Agilex™ 3 FPGA Functionality x
4.2.1.1. The Configure Menu 4.2.1.2. The GPIO Tab 4.2.1.3. The Memory Tab 4.2.1.4. The Transceiver Tab
4.2.1.2. The GPIO Tab x
4.2.1.2.1. The LED Tab 4.2.1.2.2. The Push Button Tab 4.2.1.2.3. The I2C Bus Tab
4.2.1.3. The Memory Tab x
4.2.1.3.1. The Fabric COMP Tab 4.2.1.3.2. The HPS/Fabric COMP Tab
4.2.1.4. The Transceiver Tab x
4.2.1.4.1. The DP Tab
4.2.2. Other Functionalities x
4.2.2.1. The Bottom Information Bar
5. Development Kit Hardware and Configuration x
5.1. Configuring the FPGA and Accessing HPS Debug Access Port by JTAG 5.2. Configuring the FPGA Device by Active Serial (AS) Modes (Default Mode)
6. Custom Projects for the Development Kit x
6.1. Golden Top 6.2. EMIF Pin Swizzling Setting
A. Development Kit Components x
A.1. Board Overview and Components A.2. Input and Output Components A.3. Components and Interfaces A.4. Clock Circuits A.5. System Power A.6. Power Guidelines A.7. Power Distribution System A.8. Expansion Boards
A.1. Board Overview and Components x
A.1.1. Board Overview A.1.2. Board Components
A.2. Input and Output Components x
A.2.1. Push Buttons A.2.2. Switches A.2.3. LEDs
A.3. Components and Interfaces x
A.3.1. PCI Express* ( PCIe* ) Interface A.3.2. DisplayPort Interface A.3.3. MIPI Interface A.3.4. LPDDR4 Interfaces A.3.5. Raspberry Pi* , Pmod, and PCIe* x1 Interfaces A.3.6. HPS I/O48 Interface A.3.7. I2C
A.6. Power Guidelines x
A.6.1. Primary Mode—As a Standalone Evaluation Board A.6.2. Optional Mode—As a PCIe* Add-in Card in PCIe* Host System
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
C.1.1. Safety Warnings C.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Agilex™ 3 FPGA and SoC C-Series Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

2.3.4. Installing the USB Blaster III Driver

The Agilex™ 3 FPGA and SoC C-Series Development Kit includes onboard USB Blaster III circuits for FPGA programming. However, for the host computer and board to communicate, you must install the USB Blaster III driver on the host computer.

The USB Blaster III driver is available after you install the Quartus® Prime software (version 25.1.1 or higher) in the <Quartus Prime installation directory>\quartus\drivers directory.

Related Information
Level Two Title