GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

Download PDF
ID 848344
Date 8/04/2025
Public
Document Table of Contents
Document Table of Contents x
1. GTS Transceiver Overview 2. GTS Transceiver Architecture 3. Implementing the GTS PMA/FEC Direct PHY IP 4. Implementing the GTS System PLL Clocks IP 5. Implementing the GTS Reset Sequencer IP 6. GTS PMA/FEC Direct PHY IP Example Design 7. Design Assistance Tools 8. Debugging GTS Transceiver Links with Transceiver Toolkit 9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs
1. GTS Transceiver Overview x
1.1. GTS Transceiver Design Flow
2. GTS Transceiver Architecture x
2.1. Building Blocks 2.2. Channel Placement Rules and Design Requirements 2.3. PMA Architecture 2.4. PCS Architecture 2.5. Forward Error Correction (FEC) Architecture 2.6. Clock Architecture 2.7. Bonding and Deskew
2.1. Building Blocks x
2.1.1. PMA 2.1.2. FEC 2.1.3. PCS 2.1.4. Ethernet MAC 2.1.5. PCI Express* Hard IP 2.1.6. PLL and Clock Networks 2.1.7. Avalon® Memory-Mapped Interface
2.1.1. PMA x
2.1.1.1. Protocol Support Using PMA Direct Mode
2.1.1.1. Protocol Support Using PMA Direct Mode x
2.1.1.1.1. SDI 2.1.1.1.2. HDMI 2.1.1.1.3. OTN
2.2. Channel Placement Rules and Design Requirements x
2.2.1. Hard IP Rules 2.2.2. Use Scenario Rules 2.2.3. Unused PMA Rules 2.2.4. General Design Requirement
2.2.3. Unused PMA Rules x
2.2.3.1. Unused PMA Not Planned for Use in the Future 2.2.3.2. Unused PMA Planned for Use in the Future
2.3. PMA Architecture x
2.3.1. Transmitter PMA Architecture 2.3.2. Receiver PMA Architecture 2.3.3. PMA Loopback Modes
2.3.1. Transmitter PMA Architecture x
2.3.1.1. Transmitter Buffer 2.3.1.2. Serializer 2.3.1.3. Data Pattern Generator and Verifier
2.3.2. Receiver PMA Architecture x
2.3.2.1. Receiver Buffer and Equalizer 2.3.2.2. Deserializer 2.3.2.3. CDR Block 2.3.2.4. RX PMA Tuning 2.3.2.5. RX PMA Adaptation Modes
2.3.2.1. Receiver Buffer and Equalizer x
2.3.2.1.1. Control Unit
2.3.2.5. RX PMA Adaptation Modes x
2.3.2.5.1. RX Auto Adaptation Mode 2.3.2.5.2. RX Manual Adaptation Mode 2.3.2.5.3. RX Native Adaptation Mode
2.5. Forward Error Correction (FEC) Architecture x
2.5.1. FEC Loopback Mode
2.6. Clock Architecture x
2.6.1. Reference Clock Network 2.6.2. Datapath Clock Network 2.6.3. System PLL 2.6.4. Datapath Clock Cadences 2.6.5. Shared Clocking Resources Between the GTS Transceiver Bank and HVIO Bank
2.6.1. Reference Clock Network x
2.6.1.1. PMA Primary PLL Configuration
2.6.3. System PLL x
2.6.3.1. I/O PLL in HVIO Bank as System PLL 2.6.3.2. System PLL Clock for FPGA Core 2.6.3.3. System PLL with HVIO Reference Clock
2.7. Bonding and Deskew x
2.7.1. Bonding Architecture 2.7.2. TX Deskew Function
3. Implementing the GTS PMA/FEC Direct PHY IP x
3.1. IP Overview 3.2. Designing with the GTS PMA/FEC Direct PHY IP 3.3. Configuring the GTS PMA/FEC Direct PHY IP 3.4. Dynamically Reconfigurable PHY 3.5. Signal and Port Reference 3.6. Bit Mapping for PMA, FEC, and PCS Mode PHY TX and RX Datapath 3.7. Clocking 3.8. Custom Cadence Generation Ports and Logic 3.9. Asserting Reset 3.10. Bonding Implementation 3.11. Configuration Register 3.12. Configuring the GTS PMA/FEC Direct PHY IP for Hardware Testing 3.13. Configurable Quartus® Prime Software Settings 3.14. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.1. IP Overview x
3.1.1. PMA Direct Supported Modes 3.1.2. FEC Direct Supported Modes 3.1.3. PCS Direct Supported Modes 3.1.4. Unsupported PMA/FEC/PCS Modes
3.3. Configuring the GTS PMA/FEC Direct PHY IP x
3.3.1. Preset IP Parameter Settings 3.3.2. Mode and Common Datapath Options 3.3.3. TX Datapath Options 3.3.4. RX Datapath Options 3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations 3.3.6. FEC Options 3.3.7. PCS Options 3.3.8. Avalon® Memory-Mapped Interface Options 3.3.9. Register Map IP-XACT Support 3.3.10. Analog Parameter Options
3.3.2. Mode and Common Datapath Options x
3.3.2.1. Reconfigurable PHY Settings
3.3.3. TX Datapath Options x
3.3.3.1. TX PMA Interface Parameters
3.3.4. RX Datapath Options x
3.3.4.1. RX PMA Interface Parameters
3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations x
3.3.5.1. PMA Configuration Rules for SDI Mode 3.3.5.2. PMA Configuration Rules for HDMI Mode 3.3.5.3. PMA Configuration Rules for OTN Mode
3.4. Dynamically Reconfigurable PHY x
3.4.1. Clock Generation and Constraints for Multiple Profiles Design
3.5. Signal and Port Reference x
3.5.1. TX and RX Parallel and Serial Interface Signals 3.5.2. TX and RX Reference Clock and Clock Output Interface Signals 3.5.3. Reset Signals 3.5.4. FEC Signals 3.5.5. Custom Cadence Control and Status Signals 3.5.6. RX PMA Status Signals 3.5.7. TX and RX PMA and Core Interface FIFO Signals 3.5.8. Avalon Memory-Mapped Interface Signals
3.7. Clocking x
3.7.1. Clock Ports 3.7.2. Recommended tx/rx_coreclkin Connection and tx/rx_clkout2 Source 3.7.3. Port Widths and Recommended Connections for tx/rx_coreclkin, tx/rx_clkout, and tx/rx_clkout2 3.7.4. PMA Fractional Mode 3.7.5. Input Reference Clock Buffer Protection 3.7.6. Guidelines for Obtaining the Real-Time GTS TX PLL Lock Status
3.7.5. Input Reference Clock Buffer Protection x
3.7.5.1. Reference Clock Buffer Register Information 3.7.5.2. Re-enabling the Reference Clock Buffers
3.8. Custom Cadence Generation Ports and Logic x
3.8.1. Implementing PMA Direct Mode with TX Core FIFO in Elastic Configuration 3.8.2. Enabling the i_tx_cadence_slow_clk_locked Port
3.9. Asserting Reset x
3.9.1. Reset Signal Requirements 3.9.2. Power On Reset Requirements 3.9.3. Reset Signals—Block Level 3.9.4. Run-time Reset Sequence—TX 3.9.5. Run-time Reset Sequence—RX 3.9.6. Run-time Reset Sequence—TX + RX 3.9.7. RX Data Loss/CDR Lock Loss (Auto-Recovery) 3.9.8. TX PLL Lock Loss
3.10. Bonding Implementation x
3.10.1. Bonding Placement Requirements 3.10.2. Multilane RX Simplex Implementation
3.11. Configuration Register x
3.11.1. GTS PMA and FEC Direct PHY Soft CSR Register Map 3.11.2. GTS PMA Register Map 3.11.3. Accessing Configuration Registers
3.11.2. GTS PMA Register Map x
3.11.2.1. Logical Avalon® Memory-Mapped Port Indexing
3.11.3. Accessing Configuration Registers x
3.11.3.1. Accessing GTS PMA and FEC Direct PHY Soft CSR Registers 3.11.3.2. Accessing GTS PMA Registers
3.12. Configuring the GTS PMA/FEC Direct PHY IP for Hardware Testing x
3.12.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY IP 3.12.2. Using JTAG to Avalon Master Bridge IP
3.12.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY IP x
3.12.1.1. RTL Connection Example for Debug Endpoint Avalon® Interface
3.12.2. Using JTAG to Avalon Master Bridge IP x
3.12.2.1. RTL Connection Example for JTAG to Avalon Master Bridge IP
3.13. Configurable Quartus® Prime Software Settings x
3.13.1. Configuring the RX Adaptation Mode and PMA Manual Tuning
3.14. Hardware Configuration Using the Avalon® Memory-Mapped Interface x
3.14.1. Direct Register Method 3.14.2. GTS Attribute Access Method
3.14.1. Direct Register Method x
3.14.1.1. Direct Register Method Examples
3.14.2. GTS Attribute Access Method x
3.14.2.1. GTS Attribute Access Method Example 1: Enable or Disable Internal Serial Loopback Mode (RX Auto Adaptation Mode) 3.14.2.2. GTS Attribute Access Method Example 2: Enable or Disable Internal Serial Loopback Mode (RX Manual Adaptation Mode) 3.14.2.3. GTS Attribute Access Method Example 3: Enable or Disable Polarity Inversion of the PMA 3.14.2.4. GTS Attribute Access Method Example 4: Enable PRBS Generator and Checker to Run BER Test
4. Implementing the GTS System PLL Clocks IP x
4.1. IP Parameters 4.2. IP Port List 4.3. Mode of System PLL - System PLL Reference Clock and Output Frequencies 4.4. Guidelines for GTS System PLL Clocks IP Usage 4.5. Guidelines to Indicate System PLL Reference Clock is Ready
4.5. Guidelines to Indicate System PLL Reference Clock is Ready x
4.5.1. Example Flow to Indicate System PLL Reference Clock is Ready
5. Implementing the GTS Reset Sequencer IP x
5.1. IP Requirements 5.2. IP Parameters 5.3. IP Port List 5.4. GTS Reset Sequencer IP General Interface 5.5. GTS Reset Sequencer IP Design Flow 5.6. GTS Reset Sequencer IP Use Cases 5.7. Connecting the Reference Clock Buffer Status to the GTS Reset Sequencer IP
5.6. GTS Reset Sequencer IP Use Cases x
5.6.1. Example Use Case 1 5.6.2. Example Use Case 2
6. GTS PMA/FEC Direct PHY IP Example Design x
6.1. Instantiating the GTS PMA/FEC Direct PHY IP 6.2. Generating the GTS PMA/FEC Direct PHY IP Example Design 6.3. GTS PMA/FEC Direct PHY IP Example Design Functional Description 6.4. Simulating the GTS PMA/FEC Direct PHY IP Example Design Testbench 6.5. Compiling the GTS PMA/FEC Direct PHY IP Example Design 6.6. GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design 6.7. Generating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable Example Design 6.8. GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design Functional Description 6.9. Simulating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design Testbench 6.10. Compiling the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design
6.2. Generating the GTS PMA/FEC Direct PHY IP Example Design x
6.2.1. Fast Simulation Support 6.2.2. GTS PMA/FEC Direct PHY IP Example Design Directory Structure
6.4. Simulating the GTS PMA/FEC Direct PHY IP Example Design Testbench x
6.4.1. Modifying the Example Design and Performing Simulation
6.7. Generating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable Example Design x
6.7.1. Fast Simulation Support 6.7.2. GTS PMA/FEC Direct PHY IP Reconfigurable PHY Example Design Directory Structure
7. Design Assistance Tools x
7.1. Clocking and Datapath Tool 7.2. TX Equalizer Tool
8. Debugging GTS Transceiver Links with Transceiver Toolkit x
8.1. GTS Transceiver Toolkit Parameter Settings 8.2. GTS Transceiver Toolkit GUI 8.3. GTS Transceiver Debugging Flow Walkthrough
8.2. GTS Transceiver Toolkit GUI x
8.2.1. Collection View
8.3. GTS Transceiver Debugging Flow Walkthrough x
8.3.1. Modifying the Design to Enable GTS Transceiver Debug Toolkit 8.3.2. Programming the Design into an Altera FPGA 8.3.3. Loading the Design to the Transceiver Toolkit 8.3.4. Creating Transceiver Links 8.3.5. Running BER Tests 8.3.6. Running Eye Viewer Tests 8.3.7. Running Link Optimization Tests
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY IP
4. Implementing the GTS System PLL Clocks IP
5. Implementing the GTS Reset Sequencer IP
6. GTS PMA/FEC Direct PHY IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

3.3.2. Mode and Common Datapath Options

Figure 29. GTS PMA/FEC Direct PHY IP Parameter Editor
Table 18.  Mode Parameter
Parameter Values Description
Direct PHY Operation Mode

Basic Configuration,

Dynamically Reconfigurable

Specifies the operation mode of the GTS PMA/FEC Direct PHY IP. In the Basic Configuration, mode, the IP allows the PHY to operate in PMA Direct, PCS Direct, or FEC Direct modes. In the Dynamically Reconfigurable mode, the IP requires the GTS Dynamic Reconfiguration Controller IP in the design to switch between multiple data rates. Default value is Basic Configuration.
Table 19.  Common Datapath Options Parameters
Parameter Values Description
PMA configuration rules

Basic,

SDI,

HDMI

Selects the protocol configuration rules for the GTS PMA. This parameter governs the rules for correct settings of individual parameters within the PMA.

Certain features of the PMA are available only for specific protocol configuration rules. This parameter is not a preset. You must still correctly set all other parameters for your specific protocol and application needs.

Default value is Basic.
Number of PMA lanes For TX Simplex and Duplex : 1, 2, 4

For RX Simplex : 1

Specifies the total number of PMA lanes in a bonded group. For example, if the value is 4, this means there are 4 PMA lanes bonded in the same group and share the same bonding clock. A value of 1 means there is no bonding. The number of PMA lanes is 1 when FEC is enabled.

Default value is 1.
Note: To use multiple lanes of RX simplex, you must instantiate the IP multiple times. Refer to Multilane RX Simplex Implementation for more details.

Datapath clocking mode

PMA

System PLL

Specifies whether the PMA parallel clock or System PLL is used to clock the TX/RX datapath.

You must use the System PLL setting when Enable FEC or Enable Custom PCS is on. Default value is System PLL.
System/HVIO PLL frequency 32.5 to 1000 MHz
Specifies the system PLL or HVIO PLL clock frequency (MHz) and applicable if datapath clocking mode is selected as system PLL. Default value is 322.265625 MHz.
Note: You must ensure that the system PLL frequency and GTS System PLL Clocks IP frequency is set to the same value if you are using the system PLL clocking mode.
PMA mode Duplex, TX Simplex and RX Simplex

Specifies the PMA operation mode. TX simplex and RX simplex can operate at independent rates at different PMA lanes. Default value is Duplex.
PMA data rate

10312.5 Mbps (default)

12500 Mbps (maximum)

Specifies the PMA data rate in units of Mbps (Mb/sec). Default value is 10312.5 Mbps.
PMA parallel clock frequency Data rate/PMA width Displays PMA parallel clock frequency which is PMA data rate divided by PMA interface width in MHz. Default value is Data rate / PMA Width.
PMA width 8, 10, 16, 20, 32

Specifies the PMA data width. Supported Data width is 8, 10, 16, 20 and 32 bit. Default value is 32
Provide separate interface for each PMA On/Off
When enabled, the GTS PMA/FEC Direct PHY IP presents separate data and clock interfaces for each PMA lane, rather than a wide bus. Default value is Off.
Note: When the Enable FEC option is on, a separate interface is not available for each PMA by use of the Provide separate interface for each PMA option.
Enable refclock to core On/Off Enables the reference clock to FPGA core feature.
Note: This feature is not supported when the TX PLL cascade mode is enabled.
Use HVIO PLL On/Off
Enables the use of the HVIO bank's IOPLL in place of the system PLL.
Note: This feature is currently only enabled for single bank devices and does not support the PCS/FEC Direct mode yet.
Table 20.  TX/RX Common PMA Options Parameters
Parameter Values Description
Loopback mode 17

disabled

parallel

reverse parallel

 Selects the PMA loopback mode. Default value is disabled.

Section Content
Reconfigurable PHY Settings

17 Internal serial loopback mode is not supported in the GTS PMA/FEC Direct PHY IP GUI. You must follow the steps explained in the GTS Attribute Access Method Example 2: Enable or Disable Internal Serial Loopback Mode (RX Manual Adaptation Mode) section to enable or disable the internal serial loopback mode.
Level Two Title