GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

Download PDF
ID 848344
Date 8/04/2025
Public
Document Table of Contents
Document Table of Contents x
1. GTS Transceiver Overview 2. GTS Transceiver Architecture 3. Implementing the GTS PMA/FEC Direct PHY IP 4. Implementing the GTS System PLL Clocks IP 5. Implementing the GTS Reset Sequencer IP 6. GTS PMA/FEC Direct PHY IP Example Design 7. Design Assistance Tools 8. Debugging GTS Transceiver Links with Transceiver Toolkit 9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs
1. GTS Transceiver Overview x
1.1. GTS Transceiver Design Flow
2. GTS Transceiver Architecture x
2.1. Building Blocks 2.2. Channel Placement Rules and Design Requirements 2.3. PMA Architecture 2.4. PCS Architecture 2.5. Forward Error Correction (FEC) Architecture 2.6. Clock Architecture 2.7. Bonding and Deskew
2.1. Building Blocks x
2.1.1. PMA 2.1.2. FEC 2.1.3. PCS 2.1.4. Ethernet MAC 2.1.5. PCI Express* Hard IP 2.1.6. PLL and Clock Networks 2.1.7. Avalon® Memory-Mapped Interface
2.1.1. PMA x
2.1.1.1. Protocol Support Using PMA Direct Mode
2.1.1.1. Protocol Support Using PMA Direct Mode x
2.1.1.1.1. SDI 2.1.1.1.2. HDMI 2.1.1.1.3. OTN
2.2. Channel Placement Rules and Design Requirements x
2.2.1. Hard IP Rules 2.2.2. Use Scenario Rules 2.2.3. Unused PMA Rules 2.2.4. General Design Requirement
2.2.3. Unused PMA Rules x
2.2.3.1. Unused PMA Not Planned for Use in the Future 2.2.3.2. Unused PMA Planned for Use in the Future
2.3. PMA Architecture x
2.3.1. Transmitter PMA Architecture 2.3.2. Receiver PMA Architecture 2.3.3. PMA Loopback Modes
2.3.1. Transmitter PMA Architecture x
2.3.1.1. Transmitter Buffer 2.3.1.2. Serializer 2.3.1.3. Data Pattern Generator and Verifier
2.3.2. Receiver PMA Architecture x
2.3.2.1. Receiver Buffer and Equalizer 2.3.2.2. Deserializer 2.3.2.3. CDR Block 2.3.2.4. RX PMA Tuning 2.3.2.5. RX PMA Adaptation Modes
2.3.2.1. Receiver Buffer and Equalizer x
2.3.2.1.1. Control Unit
2.3.2.5. RX PMA Adaptation Modes x
2.3.2.5.1. RX Auto Adaptation Mode 2.3.2.5.2. RX Manual Adaptation Mode 2.3.2.5.3. RX Native Adaptation Mode
2.5. Forward Error Correction (FEC) Architecture x
2.5.1. FEC Loopback Mode
2.6. Clock Architecture x
2.6.1. Reference Clock Network 2.6.2. Datapath Clock Network 2.6.3. System PLL 2.6.4. Datapath Clock Cadences 2.6.5. Shared Clocking Resources Between the GTS Transceiver Bank and HVIO Bank
2.6.1. Reference Clock Network x
2.6.1.1. PMA Primary PLL Configuration
2.6.3. System PLL x
2.6.3.1. I/O PLL in HVIO Bank as System PLL 2.6.3.2. System PLL Clock for FPGA Core 2.6.3.3. System PLL with HVIO Reference Clock
2.7. Bonding and Deskew x
2.7.1. Bonding Architecture 2.7.2. TX Deskew Function
3. Implementing the GTS PMA/FEC Direct PHY IP x
3.1. IP Overview 3.2. Designing with the GTS PMA/FEC Direct PHY IP 3.3. Configuring the GTS PMA/FEC Direct PHY IP 3.4. Dynamically Reconfigurable PHY 3.5. Signal and Port Reference 3.6. Bit Mapping for PMA, FEC, and PCS Mode PHY TX and RX Datapath 3.7. Clocking 3.8. Custom Cadence Generation Ports and Logic 3.9. Asserting Reset 3.10. Bonding Implementation 3.11. Configuration Register 3.12. Configuring the GTS PMA/FEC Direct PHY IP for Hardware Testing 3.13. Configurable Quartus® Prime Software Settings 3.14. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.1. IP Overview x
3.1.1. PMA Direct Supported Modes 3.1.2. FEC Direct Supported Modes 3.1.3. PCS Direct Supported Modes 3.1.4. Unsupported PMA/FEC/PCS Modes
3.3. Configuring the GTS PMA/FEC Direct PHY IP x
3.3.1. Preset IP Parameter Settings 3.3.2. Mode and Common Datapath Options 3.3.3. TX Datapath Options 3.3.4. RX Datapath Options 3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations 3.3.6. FEC Options 3.3.7. PCS Options 3.3.8. Avalon® Memory-Mapped Interface Options 3.3.9. Register Map IP-XACT Support 3.3.10. Analog Parameter Options
3.3.2. Mode and Common Datapath Options x
3.3.2.1. Reconfigurable PHY Settings
3.3.3. TX Datapath Options x
3.3.3.1. TX PMA Interface Parameters
3.3.4. RX Datapath Options x
3.3.4.1. RX PMA Interface Parameters
3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations x
3.3.5.1. PMA Configuration Rules for SDI Mode 3.3.5.2. PMA Configuration Rules for HDMI Mode 3.3.5.3. PMA Configuration Rules for OTN Mode
3.4. Dynamically Reconfigurable PHY x
3.4.1. Clock Generation and Constraints for Multiple Profiles Design
3.5. Signal and Port Reference x
3.5.1. TX and RX Parallel and Serial Interface Signals 3.5.2. TX and RX Reference Clock and Clock Output Interface Signals 3.5.3. Reset Signals 3.5.4. FEC Signals 3.5.5. Custom Cadence Control and Status Signals 3.5.6. RX PMA Status Signals 3.5.7. TX and RX PMA and Core Interface FIFO Signals 3.5.8. Avalon Memory-Mapped Interface Signals
3.7. Clocking x
3.7.1. Clock Ports 3.7.2. Recommended tx/rx_coreclkin Connection and tx/rx_clkout2 Source 3.7.3. Port Widths and Recommended Connections for tx/rx_coreclkin, tx/rx_clkout, and tx/rx_clkout2 3.7.4. PMA Fractional Mode 3.7.5. Input Reference Clock Buffer Protection 3.7.6. Guidelines for Obtaining the Real-Time GTS TX PLL Lock Status
3.7.5. Input Reference Clock Buffer Protection x
3.7.5.1. Reference Clock Buffer Register Information 3.7.5.2. Re-enabling the Reference Clock Buffers
3.8. Custom Cadence Generation Ports and Logic x
3.8.1. Implementing PMA Direct Mode with TX Core FIFO in Elastic Configuration 3.8.2. Enabling the i_tx_cadence_slow_clk_locked Port
3.9. Asserting Reset x
3.9.1. Reset Signal Requirements 3.9.2. Power On Reset Requirements 3.9.3. Reset Signals—Block Level 3.9.4. Run-time Reset Sequence—TX 3.9.5. Run-time Reset Sequence—RX 3.9.6. Run-time Reset Sequence—TX + RX 3.9.7. RX Data Loss/CDR Lock Loss (Auto-Recovery) 3.9.8. TX PLL Lock Loss
3.10. Bonding Implementation x
3.10.1. Bonding Placement Requirements 3.10.2. Multilane RX Simplex Implementation
3.11. Configuration Register x
3.11.1. GTS PMA and FEC Direct PHY Soft CSR Register Map 3.11.2. GTS PMA Register Map 3.11.3. Accessing Configuration Registers
3.11.2. GTS PMA Register Map x
3.11.2.1. Logical Avalon® Memory-Mapped Port Indexing
3.11.3. Accessing Configuration Registers x
3.11.3.1. Accessing GTS PMA and FEC Direct PHY Soft CSR Registers 3.11.3.2. Accessing GTS PMA Registers
3.12. Configuring the GTS PMA/FEC Direct PHY IP for Hardware Testing x
3.12.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY IP 3.12.2. Using JTAG to Avalon Master Bridge IP
3.12.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY IP x
3.12.1.1. RTL Connection Example for Debug Endpoint Avalon® Interface
3.12.2. Using JTAG to Avalon Master Bridge IP x
3.12.2.1. RTL Connection Example for JTAG to Avalon Master Bridge IP
3.13. Configurable Quartus® Prime Software Settings x
3.13.1. Configuring the RX Adaptation Mode and PMA Manual Tuning
3.14. Hardware Configuration Using the Avalon® Memory-Mapped Interface x
3.14.1. Direct Register Method 3.14.2. GTS Attribute Access Method
3.14.1. Direct Register Method x
3.14.1.1. Direct Register Method Examples
3.14.2. GTS Attribute Access Method x
3.14.2.1. GTS Attribute Access Method Example 1: Enable or Disable Internal Serial Loopback Mode (RX Auto Adaptation Mode) 3.14.2.2. GTS Attribute Access Method Example 2: Enable or Disable Internal Serial Loopback Mode (RX Manual Adaptation Mode) 3.14.2.3. GTS Attribute Access Method Example 3: Enable or Disable Polarity Inversion of the PMA 3.14.2.4. GTS Attribute Access Method Example 4: Enable PRBS Generator and Checker to Run BER Test
4. Implementing the GTS System PLL Clocks IP x
4.1. IP Parameters 4.2. IP Port List 4.3. Mode of System PLL - System PLL Reference Clock and Output Frequencies 4.4. Guidelines for GTS System PLL Clocks IP Usage 4.5. Guidelines to Indicate System PLL Reference Clock is Ready
4.5. Guidelines to Indicate System PLL Reference Clock is Ready x
4.5.1. Example Flow to Indicate System PLL Reference Clock is Ready
5. Implementing the GTS Reset Sequencer IP x
5.1. IP Requirements 5.2. IP Parameters 5.3. IP Port List 5.4. GTS Reset Sequencer IP General Interface 5.5. GTS Reset Sequencer IP Design Flow 5.6. GTS Reset Sequencer IP Use Cases 5.7. Connecting the Reference Clock Buffer Status to the GTS Reset Sequencer IP
5.6. GTS Reset Sequencer IP Use Cases x
5.6.1. Example Use Case 1 5.6.2. Example Use Case 2
6. GTS PMA/FEC Direct PHY IP Example Design x
6.1. Instantiating the GTS PMA/FEC Direct PHY IP 6.2. Generating the GTS PMA/FEC Direct PHY IP Example Design 6.3. GTS PMA/FEC Direct PHY IP Example Design Functional Description 6.4. Simulating the GTS PMA/FEC Direct PHY IP Example Design Testbench 6.5. Compiling the GTS PMA/FEC Direct PHY IP Example Design 6.6. GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design 6.7. Generating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable Example Design 6.8. GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design Functional Description 6.9. Simulating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design Testbench 6.10. Compiling the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design
6.2. Generating the GTS PMA/FEC Direct PHY IP Example Design x
6.2.1. Fast Simulation Support 6.2.2. GTS PMA/FEC Direct PHY IP Example Design Directory Structure
6.4. Simulating the GTS PMA/FEC Direct PHY IP Example Design Testbench x
6.4.1. Modifying the Example Design and Performing Simulation
6.7. Generating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable Example Design x
6.7.1. Fast Simulation Support 6.7.2. GTS PMA/FEC Direct PHY IP Reconfigurable PHY Example Design Directory Structure
7. Design Assistance Tools x
7.1. Clocking and Datapath Tool 7.2. TX Equalizer Tool
8. Debugging GTS Transceiver Links with Transceiver Toolkit x
8.1. GTS Transceiver Toolkit Parameter Settings 8.2. GTS Transceiver Toolkit GUI 8.3. GTS Transceiver Debugging Flow Walkthrough
8.2. GTS Transceiver Toolkit GUI x
8.2.1. Collection View
8.3. GTS Transceiver Debugging Flow Walkthrough x
8.3.1. Modifying the Design to Enable GTS Transceiver Debug Toolkit 8.3.2. Programming the Design into an Altera FPGA 8.3.3. Loading the Design to the Transceiver Toolkit 8.3.4. Creating Transceiver Links 8.3.5. Running BER Tests 8.3.6. Running Eye Viewer Tests 8.3.7. Running Link Optimization Tests
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY IP
4. Implementing the GTS System PLL Clocks IP
5. Implementing the GTS Reset Sequencer IP
6. GTS PMA/FEC Direct PHY IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

6.2. Generating the GTS PMA/FEC Direct PHY IP Example Design

To generate the example design you need to open the GTS PMA/FEC Direct PHY IP and go to the Example Design tab. The GTS PMA/FEC Direct PHY IP parameter editor includes the Generate Example Design function to easily create and generate simulation files to simulate a GTS PMA or FEC direct mode example design.

You can select any one of the Example Design Options for generation as shown in the following table.
Table 84.  Example Design Options
Example Design Options Description
1 x 10.3125G FEC Direct Mode (System PLL Clocking) One NRZ Firecode FEC Direct GTS lane, with a throughput of 10.3125 Gbps, with System PLL clocking mode
1 x 10.3125G Firecode FEC PCS Mode (System PLL Clocking) One NRZ Firecode FEC and PCS Direct GTS lane, with a throughput of 10.3125 Gbps, with System PLL clocking mode
1 x 10.3125G RSFEC Direct Mode (System PLL Clocking) One NRZ RS-FEC FEC Direct GTS lane, with a throughput of 10.3125 Gbps, with System PLL clocking mode
1 x 10.3125G PMA Direct Mode (System PLL Clocking) with Custom Cadence

One NRZ PMA Direct GTS lane, with a throughput of 10.3125 Gbps, with System PLL clocking mode and custom cadencing
4 x 10.3125G PMA Direct Mode (PMA Clocking)

Four NRZ PMA Direct GTS lanes, with 10.3125 Gbps per PMA lane, with PMA clocking mode
1 x 1G PMA Direct Mode (System PLL Clocking) with Custom Cadence

One NRZ PMA Direct GTS lane, with a throughput of 1Gbps, with System PLL clocking mode and custom cadencing
1 x 3.125G PMA Direct Mode (System PLL Clocking) with Custom Cadence

One NRZ PMA Direct GTS lane, with a throughput of 3.125 Gbps, with System PLL clocking mode and custom cadencing.
To generate an example design, follow the steps below:
  1. Go to the Example Design tab in the GTS PMA/FEC Direct PHY IP.
  2. Select one of the example designs from the drop-down menu. If you select None you cannot generate the example design.
  3. Click the Acknowledgement option box. This option is to remind you that only the example design you specify in the drop-down menu is generated. If you make any modification to the parameter settings of the IP after selecting the Example Design options from the drop-down list, the changes you make to the IP parameters do not take effect. Only the parameters defined for the Example Design options in the Example Design Options table take effect. If you do not check the acknowledgment box, you cannot generate the example design.
  4. Ensure steps 2 and step 3 are done, then click Generate Example Design. Clicking Generate Example Design completes the IP Generation. An example design folder is generated containing the Quartus® Prime software project (.qpf), settings (.qsf), and IP files. In addition, there are two folders created named rtl and testbench containing the RTL and simulation testbench files in the following location: 
    <Project Folder>/<directphy_example_design/example_design>
Figure 75. GTS PMA/FEC Direct PHY IP Example Design Steps
Note: If you select any of the seven available Example Design Options, but change the GTS PMA/FEC Direct PHY IP settings in the GUI thereafter, the example design generated does not follow the changed settings for the GTS PMA/FEC Direct PHY IP. The example design generation only takes the Example Design Options listed in Example Design tab of the IP Parameter editor. Any other changes that you make to the GTS PMA/FEC Direct PHY IP settings are not applied during example design generation.
Note: When you generate the GTS PMA/FEC Direct PHY IP example designs, the JTAG to Avalon Master Bridge IP instance is used to connect to the Avalon® memory-mapped interface. If you want to use the Debug Endpoint interface to connect to the Avalon® memory-mapped interface, you must enable the functionality under the Avalon® Memory-Mapped Interface tab of the IP GUI. In addition, you must change the reconfiguration interface connections of the IP by following the instructions in Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY IP.

Section Content
Fast Simulation Support
GTS PMA/FEC Direct PHY IP Example Design Directory Structure

Level Two Title