GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

Download PDF
ID 848344
Date 8/04/2025
Public
Document Table of Contents
Document Table of Contents x
1. GTS Transceiver Overview 2. GTS Transceiver Architecture 3. Implementing the GTS PMA/FEC Direct PHY IP 4. Implementing the GTS System PLL Clocks IP 5. Implementing the GTS Reset Sequencer IP 6. GTS PMA/FEC Direct PHY IP Example Design 7. Design Assistance Tools 8. Debugging GTS Transceiver Links with Transceiver Toolkit 9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs
1. GTS Transceiver Overview x
1.1. GTS Transceiver Design Flow
2. GTS Transceiver Architecture x
2.1. Building Blocks 2.2. Channel Placement Rules and Design Requirements 2.3. PMA Architecture 2.4. PCS Architecture 2.5. Forward Error Correction (FEC) Architecture 2.6. Clock Architecture 2.7. Bonding and Deskew
2.1. Building Blocks x
2.1.1. PMA 2.1.2. FEC 2.1.3. PCS 2.1.4. Ethernet MAC 2.1.5. PCI Express* Hard IP 2.1.6. PLL and Clock Networks 2.1.7. Avalon® Memory-Mapped Interface
2.1.1. PMA x
2.1.1.1. Protocol Support Using PMA Direct Mode
2.1.1.1. Protocol Support Using PMA Direct Mode x
2.1.1.1.1. SDI 2.1.1.1.2. HDMI 2.1.1.1.3. OTN
2.2. Channel Placement Rules and Design Requirements x
2.2.1. Hard IP Rules 2.2.2. Use Scenario Rules 2.2.3. Unused PMA Rules 2.2.4. General Design Requirement
2.2.3. Unused PMA Rules x
2.2.3.1. Unused PMA Not Planned for Use in the Future 2.2.3.2. Unused PMA Planned for Use in the Future
2.3. PMA Architecture x
2.3.1. Transmitter PMA Architecture 2.3.2. Receiver PMA Architecture 2.3.3. PMA Loopback Modes
2.3.1. Transmitter PMA Architecture x
2.3.1.1. Transmitter Buffer 2.3.1.2. Serializer 2.3.1.3. Data Pattern Generator and Verifier
2.3.2. Receiver PMA Architecture x
2.3.2.1. Receiver Buffer and Equalizer 2.3.2.2. Deserializer 2.3.2.3. CDR Block 2.3.2.4. RX PMA Tuning 2.3.2.5. RX PMA Adaptation Modes
2.3.2.1. Receiver Buffer and Equalizer x
2.3.2.1.1. Control Unit
2.3.2.5. RX PMA Adaptation Modes x
2.3.2.5.1. RX Auto Adaptation Mode 2.3.2.5.2. RX Manual Adaptation Mode 2.3.2.5.3. RX Native Adaptation Mode
2.5. Forward Error Correction (FEC) Architecture x
2.5.1. FEC Loopback Mode
2.6. Clock Architecture x
2.6.1. Reference Clock Network 2.6.2. Datapath Clock Network 2.6.3. System PLL 2.6.4. Datapath Clock Cadences 2.6.5. Shared Clocking Resources Between the GTS Transceiver Bank and HVIO Bank
2.6.1. Reference Clock Network x
2.6.1.1. PMA Primary PLL Configuration
2.6.3. System PLL x
2.6.3.1. I/O PLL in HVIO Bank as System PLL 2.6.3.2. System PLL Clock for FPGA Core 2.6.3.3. System PLL with HVIO Reference Clock
2.7. Bonding and Deskew x
2.7.1. Bonding Architecture 2.7.2. TX Deskew Function
3. Implementing the GTS PMA/FEC Direct PHY IP x
3.1. IP Overview 3.2. Designing with the GTS PMA/FEC Direct PHY IP 3.3. Configuring the GTS PMA/FEC Direct PHY IP 3.4. Dynamically Reconfigurable PHY 3.5. Signal and Port Reference 3.6. Bit Mapping for PMA, FEC, and PCS Mode PHY TX and RX Datapath 3.7. Clocking 3.8. Custom Cadence Generation Ports and Logic 3.9. Asserting Reset 3.10. Bonding Implementation 3.11. Configuration Register 3.12. Configuring the GTS PMA/FEC Direct PHY IP for Hardware Testing 3.13. Configurable Quartus® Prime Software Settings 3.14. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.1. IP Overview x
3.1.1. PMA Direct Supported Modes 3.1.2. FEC Direct Supported Modes 3.1.3. PCS Direct Supported Modes 3.1.4. Unsupported PMA/FEC/PCS Modes
3.3. Configuring the GTS PMA/FEC Direct PHY IP x
3.3.1. Preset IP Parameter Settings 3.3.2. Mode and Common Datapath Options 3.3.3. TX Datapath Options 3.3.4. RX Datapath Options 3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations 3.3.6. FEC Options 3.3.7. PCS Options 3.3.8. Avalon® Memory-Mapped Interface Options 3.3.9. Register Map IP-XACT Support 3.3.10. Analog Parameter Options
3.3.2. Mode and Common Datapath Options x
3.3.2.1. Reconfigurable PHY Settings
3.3.3. TX Datapath Options x
3.3.3.1. TX PMA Interface Parameters
3.3.4. RX Datapath Options x
3.3.4.1. RX PMA Interface Parameters
3.3.5. PMA Configuration Rules for Specific Protocol Mode Implementations x
3.3.5.1. PMA Configuration Rules for SDI Mode 3.3.5.2. PMA Configuration Rules for HDMI Mode 3.3.5.3. PMA Configuration Rules for OTN Mode
3.4. Dynamically Reconfigurable PHY x
3.4.1. Clock Generation and Constraints for Multiple Profiles Design
3.5. Signal and Port Reference x
3.5.1. TX and RX Parallel and Serial Interface Signals 3.5.2. TX and RX Reference Clock and Clock Output Interface Signals 3.5.3. Reset Signals 3.5.4. FEC Signals 3.5.5. Custom Cadence Control and Status Signals 3.5.6. RX PMA Status Signals 3.5.7. TX and RX PMA and Core Interface FIFO Signals 3.5.8. Avalon Memory-Mapped Interface Signals
3.7. Clocking x
3.7.1. Clock Ports 3.7.2. Recommended tx/rx_coreclkin Connection and tx/rx_clkout2 Source 3.7.3. Port Widths and Recommended Connections for tx/rx_coreclkin, tx/rx_clkout, and tx/rx_clkout2 3.7.4. PMA Fractional Mode 3.7.5. Input Reference Clock Buffer Protection 3.7.6. Guidelines for Obtaining the Real-Time GTS TX PLL Lock Status
3.7.5. Input Reference Clock Buffer Protection x
3.7.5.1. Reference Clock Buffer Register Information 3.7.5.2. Re-enabling the Reference Clock Buffers
3.8. Custom Cadence Generation Ports and Logic x
3.8.1. Implementing PMA Direct Mode with TX Core FIFO in Elastic Configuration 3.8.2. Enabling the i_tx_cadence_slow_clk_locked Port
3.9. Asserting Reset x
3.9.1. Reset Signal Requirements 3.9.2. Power On Reset Requirements 3.9.3. Reset Signals—Block Level 3.9.4. Run-time Reset Sequence—TX 3.9.5. Run-time Reset Sequence—RX 3.9.6. Run-time Reset Sequence—TX + RX 3.9.7. RX Data Loss/CDR Lock Loss (Auto-Recovery) 3.9.8. TX PLL Lock Loss
3.10. Bonding Implementation x
3.10.1. Bonding Placement Requirements 3.10.2. Multilane RX Simplex Implementation
3.11. Configuration Register x
3.11.1. GTS PMA and FEC Direct PHY Soft CSR Register Map 3.11.2. GTS PMA Register Map 3.11.3. Accessing Configuration Registers
3.11.2. GTS PMA Register Map x
3.11.2.1. Logical Avalon® Memory-Mapped Port Indexing
3.11.3. Accessing Configuration Registers x
3.11.3.1. Accessing GTS PMA and FEC Direct PHY Soft CSR Registers 3.11.3.2. Accessing GTS PMA Registers
3.12. Configuring the GTS PMA/FEC Direct PHY IP for Hardware Testing x
3.12.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY IP 3.12.2. Using JTAG to Avalon Master Bridge IP
3.12.1. Using Debug Endpoint Interface within the GTS PMA/FEC Direct PHY IP x
3.12.1.1. RTL Connection Example for Debug Endpoint Avalon® Interface
3.12.2. Using JTAG to Avalon Master Bridge IP x
3.12.2.1. RTL Connection Example for JTAG to Avalon Master Bridge IP
3.13. Configurable Quartus® Prime Software Settings x
3.13.1. Configuring the RX Adaptation Mode and PMA Manual Tuning
3.14. Hardware Configuration Using the Avalon® Memory-Mapped Interface x
3.14.1. Direct Register Method 3.14.2. GTS Attribute Access Method
3.14.1. Direct Register Method x
3.14.1.1. Direct Register Method Examples
3.14.2. GTS Attribute Access Method x
3.14.2.1. GTS Attribute Access Method Example 1: Enable or Disable Internal Serial Loopback Mode (RX Auto Adaptation Mode) 3.14.2.2. GTS Attribute Access Method Example 2: Enable or Disable Internal Serial Loopback Mode (RX Manual Adaptation Mode) 3.14.2.3. GTS Attribute Access Method Example 3: Enable or Disable Polarity Inversion of the PMA 3.14.2.4. GTS Attribute Access Method Example 4: Enable PRBS Generator and Checker to Run BER Test
4. Implementing the GTS System PLL Clocks IP x
4.1. IP Parameters 4.2. IP Port List 4.3. Mode of System PLL - System PLL Reference Clock and Output Frequencies 4.4. Guidelines for GTS System PLL Clocks IP Usage 4.5. Guidelines to Indicate System PLL Reference Clock is Ready
4.5. Guidelines to Indicate System PLL Reference Clock is Ready x
4.5.1. Example Flow to Indicate System PLL Reference Clock is Ready
5. Implementing the GTS Reset Sequencer IP x
5.1. IP Requirements 5.2. IP Parameters 5.3. IP Port List 5.4. GTS Reset Sequencer IP General Interface 5.5. GTS Reset Sequencer IP Design Flow 5.6. GTS Reset Sequencer IP Use Cases 5.7. Connecting the Reference Clock Buffer Status to the GTS Reset Sequencer IP
5.6. GTS Reset Sequencer IP Use Cases x
5.6.1. Example Use Case 1 5.6.2. Example Use Case 2
6. GTS PMA/FEC Direct PHY IP Example Design x
6.1. Instantiating the GTS PMA/FEC Direct PHY IP 6.2. Generating the GTS PMA/FEC Direct PHY IP Example Design 6.3. GTS PMA/FEC Direct PHY IP Example Design Functional Description 6.4. Simulating the GTS PMA/FEC Direct PHY IP Example Design Testbench 6.5. Compiling the GTS PMA/FEC Direct PHY IP Example Design 6.6. GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design 6.7. Generating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable Example Design 6.8. GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design Functional Description 6.9. Simulating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design Testbench 6.10. Compiling the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable PHY Example Design
6.2. Generating the GTS PMA/FEC Direct PHY IP Example Design x
6.2.1. Fast Simulation Support 6.2.2. GTS PMA/FEC Direct PHY IP Example Design Directory Structure
6.4. Simulating the GTS PMA/FEC Direct PHY IP Example Design Testbench x
6.4.1. Modifying the Example Design and Performing Simulation
6.7. Generating the GTS PMA/FEC Direct PHY IP Dynamically Reconfigurable Example Design x
6.7.1. Fast Simulation Support 6.7.2. GTS PMA/FEC Direct PHY IP Reconfigurable PHY Example Design Directory Structure
7. Design Assistance Tools x
7.1. Clocking and Datapath Tool 7.2. TX Equalizer Tool
8. Debugging GTS Transceiver Links with Transceiver Toolkit x
8.1. GTS Transceiver Toolkit Parameter Settings 8.2. GTS Transceiver Toolkit GUI 8.3. GTS Transceiver Debugging Flow Walkthrough
8.2. GTS Transceiver Toolkit GUI x
8.2.1. Collection View
8.3. GTS Transceiver Debugging Flow Walkthrough x
8.3.1. Modifying the Design to Enable GTS Transceiver Debug Toolkit 8.3.2. Programming the Design into an Altera FPGA 8.3.3. Loading the Design to the Transceiver Toolkit 8.3.4. Creating Transceiver Links 8.3.5. Running BER Tests 8.3.6. Running Eye Viewer Tests 8.3.7. Running Link Optimization Tests
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY IP
4. Implementing the GTS System PLL Clocks IP
5. Implementing the GTS Reset Sequencer IP
6. GTS PMA/FEC Direct PHY IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide: Agilex™ 3 FPGAs and SoCs

3.8. Custom Cadence Generation Ports and Logic

When using system PLL clocking mode, you must enable the Custom cadence generation (CCG) ports and logic parameter for the use cases that the Custom Cadence Generation Ports and Logic Use Cases table below describes. Enabling CCG logic ensures that the TX PMA interface FIFO does not overflow due to the over clocking of the datapath when using system PLL clocking mode.

For PMA clocking with Elastic mode, the custom cadence generation (CCG) ports and logic are enabled by default.

Table 59.  Custom Cadence Generation Ports and Logic Use Cases
Configuration Datapath Clocking mode System PLL Frequency Enable Custom Cadence Generation (CCG) Ports and Logic
PMA Direct PMA N/A No
PMA Direct System PLL Equal to PMA parallel clock frequency. No PPM between PMA parallel clock frequency and system PLL frequency. That is, the same reference clock source for PMA and system PLL.22 No
PMA Direct System PLL Greater than the PMA parallel clock frequency. Yes
PMA Direct with Elastic mode PMA N/A When you are using PMA clocking with the Elastic mode configuration, the CCG ports and logic are enabled by default.
FEC Direct System PLL Equal to the PMA Parallel clock frequency. No PPM between PMA parallel clock frequency and system PLL frequency. That is, the same reference clock source for PMA and system PLL. No
FEC Direct System PLL Equal to the PMA Parallel clock frequency. PPM between PMA parallel clock frequency and system PLL frequency. That is, different reference clock for PMA and system PLL. Yes
FEC Direct System PLL Greater than the PMA parallel clock frequency. Yes
When you enable Custom cadence generation (CCG) ports and logic or enable PMA clocking with Elastic mode, the o_tx_cadence, i_tx_cadence_fast_clk, and i_tx_cadence_slow_clk ports are available in the GTS PMA/FEC Direct PHY IP. CCG logic uses the i_tx_cadence_fast_clk and i_tx_cadence_slow_clk inputs (does not monitor PMA Interface FIFO status), and generates a o_tx_cadence output signal. You must use o_tx_cadence to assert and de-assert the TX PMA Interface data valid bit. This bit is one of the bits in TX parallel data. Refer to Parallel Data Mapping Information.
Table 60.  tx_cadence_fast_clk and tx_cadence_slow_clk connections
Configuration Enable TX Double Width Transfer Recommended Connections
PMA Direct (Elastic mode)

PMA Direct (Elastic mode/Phase Compensation)

 Yes
  • Connect i_tx_cadence_fast_clk to tx user clock/2
  • Connect i_tx_cadence_slow_clk to word clock/2
PMA Direct (Elastic mode)

PMA Direct (Elastic mode/Phase Compensation)

 No
  • Connect i_tx_cadence_fast_clk to tx user clock
  • i_tx_cadence_slow_clk to word clock
PMA Direct (Phase Compensation/Elastic mode) Yes
  • Connect i_tx_cadence_fast_clk to word clock/2
  • i_tx_cadence_slow_clk to word clock/2
PMA Direct (Phase Compensation/Elastic mode) No
  • Connect i_tx_cadence_fast_clk to word clock
  • i_tx_cadence_slow_clk to word clock
FEC Direct Yes
  • Connect i_tx_cadence_fast_clk to System PLL Clock Div2
  • i_tx_cadence_slow_clk to User Clock (DIV 66)

Section Content
Implementing PMA Direct Mode with TX Core FIFO in Elastic Configuration
Enabling the i_tx_cadence_slow_clk_locked Port

22 When using PMA direct with system PLL clocking mode, if the reference clock for PMA and system PLL are from different clock source, then the system PLL frequency cannot be equal to the PMA parallel clock frequency. System PLL frequency must be greater than or equal to the fastest possible TX and RX PMA clock, including PPM.
Level Two Title