PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

Download PDF
ID 683716
Date 4/10/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the PHY Lite for Parallel Interfaces IP 2. PHY Lite for Parallel Interfaces Intel Agilex 7 FPGA IP for M-Series 3. PHY Lite for Parallel Interfaces Intel Agilex 7 FPGA IP for F-Series and I-Series 4. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP 5. PHY Lite for Parallel Interfaces Intel Arria 10 and Intel Cyclone 10 GX FPGA IPs 6. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives 7. Document Revision History for the PHY Lite for Parallel Interfaces IP User Guide
1. About the PHY Lite for Parallel Interfaces IP x
1.1. Device Family Support 1.2. Features
2. PHY Lite for Parallel Interfaces Intel Agilex 7 FPGA IP for M-Series x
2.1. Release Information 2.2. Functional Description 2.3. Getting Started 2.4. I/O Standards 2.5. Design Example
2.2. Functional Description x
2.2.1. PHY Lite for Parallel Interfaces Intel® Agilex™ FPGA IP Top Level Interfaces 2.2.2. Dynamic Reconfiguration
2.2.1. PHY Lite for Parallel Interfaces Intel® Agilex™ FPGA IP Top Level Interfaces x
2.2.1.1. Clocks 2.2.1.2. Output Path 2.2.1.3. Input Path
2.2.1.1. Clocks x
2.2.1.1.1. Clock Frequency Relationships
2.2.2. Dynamic Reconfiguration x
2.2.2.1. Calibration IP 2.2.2.2. Dynamic Reconfigurable Delays 2.2.2.3. Register Map
2.3. Getting Started x
2.3.1. Parameter Settings 2.3.2. Signals
2.3.2. Signals x
2.3.2.1. Clock and Reset Interface Signals 2.3.2.2. Output Path Signals 2.3.2.3. Input Path Signals
2.4. I/O Standards x
2.4.1. Design Guidelines
2.4.1. Design Guidelines x
2.4.1.1. DQS Trees 2.4.1.2. Pin Placement Restrictions
2.5. Design Example x
2.5.1. Generate the Design Example 2.5.2. Verify Simulation Design Examples using Tester IP
2.5.1. Generate the Design Example x
2.5.1.1. Design Example without Dynamic Reconfiguration 2.5.1.2. Dynamic Reconfiguration Design Examples
2.5.1.1. Design Example without Dynamic Reconfiguration x
2.5.1.1.1. Generate the Synthesis Design Example 2.5.1.1.2. Generate the Simulation Design Example
2.5.1.2. Dynamic Reconfiguration Design Examples x
2.5.1.2.1. Generate the Synthesis Design Example 2.5.1.2.2. Generate the Simulation Design Example
3. PHY Lite for Parallel Interfaces Intel Agilex 7 FPGA IP for F-Series and I-Series x
3.1. Release Information 3.2. Functional Description 3.3. Getting Started 3.4. I/O Standards 3.5. Design Guidelines 3.6. Design Example
3.2. Functional Description x
3.2.1. Intel® Agilex™ 7 for F-Series and I-Series I/O Sub-bank Interconnects 3.2.2. Intel® Agilex™ 7 for F-Series and I-Series Input DQS/Strobe Tree 3.2.3. PHY Lite for Parallel Interfaces Intel® Agilex™ 7 for F-Series and I-Series FPGA IP Top Level Interfaces 3.2.4. Dynamic Reconfiguration 3.2.5. I/O Timing
3.2.3. PHY Lite for Parallel Interfaces Intel® Agilex™ 7 for F-Series and I-Series FPGA IP Top Level Interfaces x
3.2.3.1. Clocks 3.2.3.2. Output Path 3.2.3.3. Input Path
3.2.3.1. Clocks x
3.2.3.1.1. Clock Frequency Relationships
3.2.4. Dynamic Reconfiguration x
3.2.4.1. Connectivity 3.2.4.2. Reconfiguration Features and Register Addressing 3.2.4.3. Dynamic Reconfiguration Guidelines
3.2.4.2. Reconfiguration Features and Register Addressing x
3.2.4.2.1. Control Registers Addresses 3.2.4.2.2. Control Registers
3.2.4.3. Dynamic Reconfiguration Guidelines x
3.2.4.3.1. Strobe Enable Window Calibration 3.2.4.3.2. Output and Strobe Enable Minimum and Maximum Phase Settings 3.2.4.3.3. Input DQ/DQS Delay Chains Maximum Values
3.3. Getting Started x
3.3.1. Parameter Settings 3.3.2. Signals
3.3.1. Parameter Settings x
3.3.1.1. Read Latency 3.3.1.2. Write Latency
3.3.2. Signals x
3.3.2.1. Clock and Reset Interface Signals 3.3.2.2. Output Path Signals 3.3.2.3. Input Path Signals
3.4. I/O Standards x
3.4.1. Input Buffer Reference Voltage (VREF) 3.4.2. On-Chip Termination (OCT)
3.4.2. On-Chip Termination (OCT) x
3.4.2.1. RZQ_GROUP Assignment
3.5. Design Guidelines x
3.5.1. Guidelines: Group Pin Placement 3.5.2. Reference Clock 3.5.3. Reset
3.6. Design Example x
3.6.1. Generate the Design Example
3.6.1. Generate the Design Example x
3.6.1.1. Design Example without Dynamic Reconfiguration 3.6.1.2. Dynamic Reconfiguration Design Examples
3.6.1.1. Design Example without Dynamic Reconfiguration x
3.6.1.1.1. Generate the Synthesis Design Example 3.6.1.1.2. Generate the Simulation Design Example
3.6.1.2. Dynamic Reconfiguration Design Examples x
3.6.1.2.1. Generate the Synthesis Design Example 3.6.1.2.2. Generate the Simulation Design Example
4. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP x
4.1. Release Information 4.2. Functional Description 4.3. Getting Started 4.4. I/O Standards 4.5. Design Guidelines 4.6. Design Example
4.2. Functional Description x
4.2.1. Top Level Interfaces 4.2.2. Clocks 4.2.3. Output Path 4.2.4. Input Path 4.2.5. Dynamic Reconfiguration
4.2.2. Clocks x
4.2.2.1. Clock Frequency Relationships
4.2.3. Output Path x
4.2.3.1. Output Path Data Alignment
4.2.4. Input Path x
4.2.4.1. Input Path Data Alignment
4.2.5. Dynamic Reconfiguration x
4.2.5.1. RTL Connectivity 4.2.5.2. Address Lookup 4.2.5.3. Reconfiguration Features and Register Addressing 4.2.5.4. Calibration Guidelines
4.2.5.1. RTL Connectivity x
4.2.5.1.1. Daisy Chain
4.2.5.2. Address Lookup x
4.2.5.2.1. Strobes 4.2.5.2.2. Parameter Table Examples
4.2.5.3. Reconfiguration Features and Register Addressing x
4.2.5.3.1. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP Control Registers Addresses 4.2.5.3.2. Control Registers Description
4.2.5.4. Calibration Guidelines x
4.2.5.4.1. Strobe Enable Window Calibration 4.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
4.3. Getting Started x
4.3.1. Parameter Settings 4.3.2. Signals
4.3.1. Parameter Settings x
4.3.1.1. Read Latency 4.3.1.2. Write Latency
4.3.2. Signals x
4.3.2.1. Clock and Reset Interface Signals 4.3.2.2. Output Path Signals 4.3.2.3. Input Path Signals 4.3.2.4. Avalon Configuration Bus Interface Signals 4.3.2.5. Termination Signals
4.4. I/O Standards x
4.4.1. Input Buffer Reference Voltage (VREF) 4.4.2. On-Chip Termination (OCT)
4.4.1. Input Buffer Reference Voltage (VREF) x
4.4.1.1. Calibrated VREF Settings
4.4.2. On-Chip Termination (OCT) x
4.4.2.1. RZQ_GROUP Assignment 4.4.2.2. Manual Insertion of OCT Block
4.5. Design Guidelines x
4.5.1. Guidelines: Group Pin Placement 4.5.2. Reference Clock 4.5.3. Reset 4.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 4.5.5. Dynamic Reconfiguration 4.5.6. Timing
4.5.6. Timing x
4.5.6.1. Timing Components 4.5.6.2. Timing Constraints and Files 4.5.6.3. Timing Analysis 4.5.6.4. Timing Closure Guidelines
4.5.6.2. Timing Constraints and Files x
4.5.6.2.1. <variation_name>.sdc 4.5.6.2.2. <variation_name>_parameter.tcl 4.5.6.2.3. <variation_name>_ip_parameters.tcl 4.5.6.2.4. <variation_name>_pin_map.tcl 4.5.6.2.5. <variation_name>_report_timing.tcl 4.5.6.2.6. <variation_name>_report_timing_core.tcl
4.5.6.4. Timing Closure Guidelines x
4.5.6.4.1. Timing Closure: Dynamic Reconfiguration 4.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 4.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 4.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 4.5.6.4.5. I/O Timing Violation 4.5.6.4.6. Internal FPGA Path Timing Violation
4.6. Design Example x
4.6.1. Generate the Design Example
4.6.1. Generate the Design Example x
4.6.1.1. Design Example without Dynamic Reconfiguration 4.6.1.2. Dynamic Reconfiguration Design Examples
4.6.1.1. Design Example without Dynamic Reconfiguration x
4.6.1.1.1. Generate the Hardware Design Example 4.6.1.1.2. Generate the Simulation Design Example
4.6.1.2. Dynamic Reconfiguration Design Examples x
4.6.1.2.1. Dynamic Reconfiguration Using Finite State Machine
5. PHY Lite for Parallel Interfaces Intel Arria 10 and Intel Cyclone 10 GX FPGA IPs x
5.1. Release Information 5.2. Functional Description 5.3. Getting Started 5.4. I/O Standards 5.5. Design Guidelines 5.6. Design Example 5.7. Application Specific Design Example
5.2. Functional Description x
5.2.1. Top Level Interfaces 5.2.2. Clocks 5.2.3. Output Path 5.2.4. Input Path 5.2.5. Dynamic Reconfiguration
5.2.2. Clocks x
5.2.2.1. Clock Frequency Relationships
5.2.3. Output Path x
5.2.3.1. Output Path Data Alignment
5.2.4. Input Path x
5.2.4.1. Input Path Data Alignment
5.2.5. Dynamic Reconfiguration x
5.2.5.1. RTL Connectivity 5.2.5.2. Address Lookup 5.2.5.3. Reconfiguration Features and Register Addressing 5.2.5.4. Calibration Guidelines
5.2.5.1. RTL Connectivity x
5.2.5.1.1. Daisy Chain
5.2.5.2. Address Lookup x
5.2.5.2.1. Strobes 5.2.5.2.2. Parameter Table Examples
5.2.5.3. Reconfiguration Features and Register Addressing x
5.2.5.3.1. PHY Lite for Parallel Interfaces Intel Arria 10 FPGA IP and PHY Lite for Parallel Interfaces Intel Cyclone 10 GX IPs Address Registers 5.2.5.3.2. Control Registers Description
5.2.5.4. Calibration Guidelines x
5.2.5.4.1. Strobe Enable Window Calibration 5.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
5.3. Getting Started x
5.3.1. Parameter Settings 5.3.2. Signals
5.3.1. Parameter Settings x
5.3.1.1. Read Latency 5.3.1.2. Write Latency
5.3.2. Signals x
5.3.2.1. Clock and Reset Interface Signals 5.3.2.2. Output Path Signals 5.3.2.3. Input Path Signals 5.3.2.4. Avalon Configuration Bus Interface Signals 5.3.2.5. Termination Signals
5.4. I/O Standards x
5.4.1. Input Buffer Reference Voltage (VREF) 5.4.2. On-Chip Termination (OCT)
5.4.1. Input Buffer Reference Voltage (VREF) x
5.4.1.1. Calibrated VREF Settings
5.4.2. On-Chip Termination (OCT) x
5.4.2.1. RZQ_GROUP Assignment 5.4.2.2. Manual Insertion of OCT Block
5.5. Design Guidelines x
5.5.1. Guidelines: Group Pin Placement 5.5.2. Reference Clock 5.5.3. Reset 5.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 5.5.5. Dynamic Reconfiguration 5.5.6. Timing
5.5.6. Timing x
5.5.6.1. Timing Components 5.5.6.2. Timing Constraints and Files 5.5.6.3. Timing Analysis 5.5.6.4. Timing Closure Guidelines
5.5.6.2. Timing Constraints and Files x
5.5.6.2.1. <variation_name>.sdc 5.5.6.2.2. <variation_name>_parameter.tcl 5.5.6.2.3. <variation_name>_ip_parameters.tcl 5.5.6.2.4. <variation_name>_pin_map.tcl 5.5.6.2.5. <variation_name>_report_timing.tcl 5.5.6.2.6. <variation_name>_report_timing_core.tcl
5.5.6.4. Timing Closure Guidelines x
5.5.6.4.1. Timing Closure: Dynamic Reconfiguration 5.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 5.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 5.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 5.5.6.4.5. I/O Timing Violation 5.5.6.4.6. Internal FPGA Path Timing Violation
5.6. Design Example x
5.6.1. Generate the Design Example
5.6.1. Generate the Design Example x
5.6.1.1. Design Example without Dynamic Reconfiguration 5.6.1.2. Dynamic Reconfiguration Design Examples
5.6.1.1. Design Example without Dynamic Reconfiguration x
5.6.1.1.1. Generate the Hardware Design Example 5.6.1.1.2. Generate the Simulation Design Example
5.6.1.2. Dynamic Reconfiguration Design Examples x
5.6.1.2.1. Dynamic Reconfiguration with Debug Kit 5.6.1.2.2. Dynamic Reconfiguration Using Finite State Machine
5.7. Application Specific Design Example x
5.7.1. Implementation using the PHY Lite for Parallel Interfaces IP
1. About the PHY Lite for Parallel Interfaces IP
2. PHY Lite for Parallel Interfaces Intel Agilex 7 FPGA IP for M-Series
3. PHY Lite for Parallel Interfaces Intel Agilex 7 FPGA IP for F-Series and I-Series
4. PHY Lite for Parallel Interfaces Intel Stratix 10 FPGA IP
5. PHY Lite for Parallel Interfaces Intel Arria 10 and Intel Cyclone 10 GX FPGA IPs
6. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives
7. Document Revision History for the PHY Lite for Parallel Interfaces IP User Guide

2.3.1. Parameter Settings

Table 14.   PHY Lite for Parallel Interfaces IP Parameter Settings
Parameter Values Default Values Description
Parameter
Number of groups 1 - 8 1 Number of data and strobe groups in the interface. The value is set to 1 by default.
I/O Instance ID 0 - 7 0 To be used to assign different base addressed to two instances in the same bank.
General Tab- these parameters are set on a per interface basis
Clocks
Interface clock frequency

150 MHz - 1250 MHz

 533.0 MHz External interface clock frequency.
Use recommended PLL reference clock frequency On, Off On

Turn this option on to calculate the PLL reference clock frequency automatically for best performance.

Turn this option off to specify your own PLL reference clock frequency.
PLLreference clock frequency Dependent on interface clock frequency 266.5 MHz

PLL reference clock frequency. You must feed a clock of this frequency to the PLL reference clock input of the memory interface.

Select the desired PLL reference clock frequency from the drop-down list. The values in the list changes when you change the interface clock frequency or the user clock rate logic.

VCO clock frequency Calculated internally by PLL 1066.0 MHz The frequency of this clock is calculated internally by the PLL based on the interface clock and the core clock rate.
Core clock frequency Calculated internally by PLL 266.5 MHz The frequency of this clock is calculated internally by the PLL based on clock rate of user logic.
Dynamic Reconfiguration
Use dynamic reconfiguration On, Off Off

Exposes an Avalon® memory-mapped interface, allowing you to control the configuration of the PHY Lite for Parallel Interfaces IP settings.

Note: The PHY Lite for Parallel Interfaces IP does not support dynamic reconfiguration feature in the Intel® Quartus® Prime version 20.3.
I/O Settings
I/O standard

SSTL-12

1.2-V POD

1.1-V POD

1.2-V HSTL

1.2-V HSUL

1.1-V LVSTL

1.05-V LVSTL

 SSTL-12 Specifies the I/O standard of the interface's strobe and data pins written.
Reference clock I/O configuration

Single-ended,

True Differential with on-chip termination,

True Differential without on-chip termination

 Single-ended Specifies the reference clock I/O configuration.
Group<x> - these parameters are set on a per group basis
Group<x> Pin Settings
Pin type Input, Output, Bidirectional Bidirectional Direction of data pins. This value is set to Bidirectional by default.
Pin width 1 to 22 8 Number of pins in this data/strobe group. The pin width includes the number of strobe pins.
DDR/SDR DDR, SDR DDR Double/single data rate.
Data Configuration Differential, Single-ended Differential Select the type of data.
Group<x> Input Path Settings
Additional receiver enable latency 0 to 15 0 The number of external interface clock cycles to delay the internal receiver enable signal in addition to the inherent latency in the receiver enable path. The valid range depends on the user clock rate and memory interface frequency set in the General tab.
Capture strobe phase shift 0, 45, 90 90 Internally phase shift the input strobe relative to input data.
Group<x> Output Path Settings
Additional write latency 0 to 15 0 The number of external interface clock cycles to delay the output data in addition to the inherent write latency. The valid range is the set of sub core clock cycles, which is dependent on the user clock rate set in the General tab. To delay by a larger amount, the data should be registered in the core.
Output strobe phase

0, 45, 90, 135,

180

 90 Phase shift of the output strobe relative to the output data.

Group<x> General Strobe Settings

Note: These parameters are disabled when Copy parameters from another group is enabled.
Strobe configuration Differential, Single-ended Differential

Select the type of strobe.

Refer to the I/O Standards table for a list of supported I/O standards.

Group<x> OCT Settings
Use Default OCT Values On, Off On Use default OCT values based on the I/O standard parameter setting.
Input OCT Value

40 ohm with calibration,

50 ohm with calibration,

50 ohm without calibration,

60 ohm with calibration

 60 ohm with calibration

Specifies the group's data and strobe input termination values.

Disables the Use Default OCT Values parameter to select the desired input OCT value.

Output OCT Value

34 ohm with calibration,

34 ohm without calibration,

40 ohm with calibration,

40 ohm without calibration

 40 ohm with calibration

Specifies the group's data and strobe output termination values.

Disable the Use Default OCT Values parameter to select the desired output OCT value.

Pin Placement
RZQ Index 38, 62 38 Specifies the RZQ pin index in the I/O bank. It should be reserved at pin 38 or pin 62.

Pin Parameter Settings

Enable manual location of data pins

On, Off Off By default, all the data pins are placed in an ordered-dense format i.e., no gap pins. Enable this option if data pins are required to be spaced out i.e. with gap-pins. Adhere to all restrictions in the user guide.
Pin Placement Settings Comma separated values — Provides a CSV list of pin locations one per each data pin. For example, a value of 0, 1, 8, 9 places data[0], data[1], data[2], data[3] on pin0, pin1, pin8, pin9 of IO48 Tile respectively, leaving pin2-7 not used for data. These unused pins may be used for PLL Reference Clocks, RZQ Pin or Strobes (subject to the constraints mentioned in the User Guide).
Related Information
Level Two Title