Quartus® Prime Pro Edition User Guide: Design Compilation

ID 683236
Date 4/01/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

1.10.6. Retiming Restrictions and Workarounds

The Compiler identifies the register chains in your design that limit further optimization through Hyper-Retiming. The Compiler refers to these related register-to-register paths as a critical chain. The fMAX of the critical chain and its associated clock domain is limited by the average delay of a register-to-register path, and quantization delays of indivisible circuit elements like routing wires. There are a variety of situations that cause retiming restrictions. Retiming restrictions exist because of hardware characteristics, software behavior, or are inherent to the design. The Retiming Limit Details report the limiting reasons preventing further retiming, and the registers and combinational nodes that comprise the chain. The Fast Forward recommendations list the steps you can take to remove critical chains and enable additional register retiming.

In the diagram of a simple critical chain that follows, the red line represents the same critical chain. Timing restrictions prevent register A from retiming forward. Timing restrictions also prevent register B from retiming backwards. A loop occurs when register A and register B are the same register.

Figure 113. Sample Critical Chain

Particular registers in critical chains can limit performance for many other reasons. The Compiler classifies the following types of reasons that limit further optimization by retiming:

  • Insufficient Registers—indicates insufficient quantity of registers at either end of the chain for retiming. Adding more registers can improve performance.
  • Short Path/Long Path—indicates that the critical chain has dependent paths with conflicting characteristics. For example, one path improves performance with more registers, and another path has no place for additional hyper-registers.
  • Path Limit—indicates that there are no further Hyper-Register locations available on the critical path, or the design reached a performance limit of the current place and route.
  • Loops—indicates a feedback path in a circuit. When the critical chain includes a feedback loop, retiming cannot change the number of registers in the loop without changing functionality. The Compiler can retime around the loop without changing functionality. However, the Compiler cannot place additional registers in the loop.

After understanding why a particular critical chain limits your design’s performance, you can then make RTL changes to eliminate that bottleneck and increase performance.

Table 25.  Hyper-Register Support for Various Design Conditions
Design Condition Hyper-Register Support
Initial conditions that cannot be preserved Hyper-Registers do have initial condition support. However, you cannot perform some retiming operations while preserving the initial condition stage of all registers (that is, the merging and duplicating of Hyper-Registers). If this condition occurs in the design, the Fitter does not retime those registers. This retiming limit ensures that the register retiming does not affect design functionality.
Register has an asynchronous clear Hyper-Registers support only data and clock inputs. Hyper-Registers do not have control signals such as asynchronous clears, presets, or enables. The Fitter cannot retime any register that has an asynchronous clear. Use asynchronous clears only when necessary, such as state machines or control logic. Often, you can avoid or remove asynchronous clears from large parts of a datapath.
Register drives an asynchronous signal This design condition is inherent to any design that uses asynchronous resets. Focus on reducing the number of registers that are reset with an asynchronous clear.
Register has don’t touch or preserve attributes The Compiler does not retime registers with these attributes. If you use the preserve attribute to manage register duplication for high fan-out signals, try removing the preserve attribute. The Compiler may be able to retime the high fan-out register along each of the routing paths to its destinations. Alternatively, use the dont_merge attribute. The Compiler retimes registers in ALMs, DDIOs, single port RAMs, and DSP blocks.
Register is a clock source This design condition is uncommon, especially for performance-critical parts of a design. If this retiming restriction prevents you from achieving the required performance, consider whether a PLL can generate the clock, rather than a register.
Register is a partition boundary This condition is inherent to any design that uses design partitions. If this retiming restriction prevents you from achieving the required performance, add additional registers inside the partition boundary for Hyper-Retiming.
Register is a block type modified by an ECO operation This restriction is uncommon. Avoid the restriction by making the functional change in the design source and recompiling, rather than performing an ECO.
Register location is an unknown block This restriction is uncommon. You can often work around this condition by adding extra registers adjacent to the specified block type.
Register is described in the RTL as a latch Hyper-Registers cannot implement latches. The Compiler infers latches because of RTL coding issues, such as incomplete assignments. If you do not intend to implement a latch, change the RTL.
Register location is at an I/O boundary All designs contain I/O, but you can add additional pipeline stages next to the I/O boundary for Hyper-Retiming.
Combinational node is fed by a special source This condition is uncommon, especially for performance-critical parts of a design.
Register is driven by a locally routed clock Only the dedicated clock network clocks Hyper-Registers. Using the routing fabric to distribute clock signals is uncommon, especially for performance-critical parts of a design. Consider implementing a small clock region instead.
Register is a timing exception end-point The Compiler does not retime registers that are sources or destinations of .sdc constraints.
Register with inverted input or output This condition is uncommon.
Register is part of a synchronizer chain The Fitter optimizes synchronizer chains to increase the mean time between failure (MTBF), and the Compiler does not retime registers that are detected or marked as part of a synchronizer chain. Add more pipeline stages at the clock domain boundary adjacent to the synchronizer chain to provide flexibility for the retiming. Alternatively, you can reduce the detection number for that particular synchronizer chain Synchronization Register Chain Length (default is 3). In some cases a synchronizer chain isn't necessary, and shouldn't be inferred.
Register with multiple period requirements for paths that start or end at the register (cross-clock boundary) This situation occurs at any cross-clock boundary, where a register latches data on a clock at one frequency, and fans out to registers running at another frequency. The Compiler does not retime registers at cross-clock boundaries. Consider adding additional pipeline stages at one side of the clock domain boundary, or the other, to provide flexibility for retiming.