DisplayPort Intel® FPGA IP User Guide

ID 683273
Date 4/18/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

5.8. Source Interfaces

The following tables list the source’s port interfaces. Your instantiation contains only the interfaces that you have enabled.

Table 20.  Controller Interface

Interface

Port Type

Clock Domain

Port

Direction

Description

clk

Clock

N/A

clk

Input

Clock for embedded controller

reset

Reset

clk

reset

Input

Reset for embedded controller

tx_mgmt

AV-MM

clk tx_mgmt_address[8:0] Input

32-bit word addressing address

tx_mgmt_chipselect

Input

Assert for valid read or write access

tx_mgmt_read Input

Assert to indicate a read transfer

tx_mgmt_write Input

Assert to indicate a write transfer

tx_mgmt_writedata[31:0] Input

Data for write transfers

tx_mgmt_readdata[31:0] Output Data for read transfers
tx_mgmt_waitrequest Output Asserted when the DisplayPort Intel® FPGA IP is unable to respond to a read or write request. Forces the GPU to wait until the IP is ready to proceed with the transfer.

tx_mgmt_irq

IRQ

clk

tx_mgmt_irq

Output Interrupt for embedded controller
Table 21.  Transceiver Management Interface n is the number of TX lanes.

Interface

Port Type

Clock Domain

Port

Direction

Description

xcvr_mgmt_clk

Clock

N/A

xcvr_mgmt_clk Input

Transceiver management clock

clk_cal

Clock

N/A

clk_cal Input

A 50-MHz calibration clock input. This clock must be synchronous to the clock used for the Transceiver Reconfiguration block (xvcr_mgmt_clk), external to the DisplayPort source.

tx_analog_reconfig

Conduit

xcvr_mgmt_clk tx_vod[2n - 1:0] Output

Transceiver analog reconfiguration handshaking

tx_emp[2n - 1:0] Output
tx_analog_reconfig_req Output
tx_analog_reconfig_ack Input
tx_analog_reconfig_busy Input

tx_reconfig

Conduit

xcvr_mgmt_clk tx_link_rate_8bits[7:0] Output

Transceiver link rate reconfiguration handshaking

tx_reconfig_req Input
tx_reconfig_ack Input
tx_reconfig_busy Input

     

Note: Value of tx_link_rate[1:0]: 0 = 1.62 Gbps, 1 = 2.70 Gbps, 2 = 5.40 Gbps, 3 = 8.10 Gbps; value of tx_link_rate_8bits[7:0]: 0x06 = 1.62 Gbps, 0x0a = 2.70 Gbps, 0x14 = 5.40 Gbps, 0x1e = 8.10 Gbps, 0x01 = 10 Gbps.
Note: tx_link_rate [1:0] is depreciated
Note: For devices using a 50-MHz xcvr_mgmt_clk clock, connect the same clock directly also to the clk_cal signal. For devices using a 100-MHz xcvr_mgmt_clk clock, connect the same clock to clk_cal signal through a by-2 divider.

Transceiver Analog Reconfiguration Interface

Transceiver Reconfiguration Interface

Video Interface

When you turn off Enable Video input Image port, the source uses the standard HSYNC/VSYNC/DE ports in txN_vid_clk and txN_video_in interfaces.

Table 22.  Video Interface (HSYNC/VSYNC/DE Interface) v is the number of bits per color, p is the pixels per clock (1 = single, 2 = dual, and 4 = quad). N is the stream number; for example, tx_vid_clk represents Stream 0, tx1_vid_clk represents Stream 1, and so on.

Interface

Port Type

Clock Domain

Port

Direction

Description

txN_vid_clk

Clock

N/A

txN_vid_clk Input

Video clock

txN_video_in

Conduit

txN_vid_clk txN_vid_data[3v*p-1:0] Input

Video data and standard H/V synchronization video port input

txN_vid_v_sync[p-1:0] Input
txN_vid_h_sync[p-1:0] Input
txN_vid_de[p-1:0] Input

When you turn on Enable Video input Image port, the source uses the txN_im_clk and txN_video_in_im interfaces.

Table 23.  Video Interface (TX Video IM Interface) v is the number of bits per color, p is the pixels per clock (1 = single, 2 = dual, and 4 = quad). N is the stream number; for example, tx_im_clk represents Stream 0, tx1_im_clk represents Stream 1, and so on.

Interface

Port Type

Clock Domain

Port

Direction

Description

txN_im_clk

Clock

N/A

txN_im_clk Input

Video Image clock

txN_video_in

Conduit

txN_im_clk txN_im_sol Input

Start of video line

txN_im_eol Input

End of video line

txN_im_sof Input

Start of video frame

txN_im_eof Input

End of video frame

txN_im_data[3v*p-1:0] Input

Video input data

txN_im_valid[p-1:0] Input

Video data valid. Each bit must assert when all other signals on this port are valid and the corresponding pixel belongs to active video.

txN_im_locked Input
Video locked
  • 0 = Unlocked
  • 1 = Locked
txN_im_interlace Input
Video interlaced
  • 0 = Progressive video
  • 1 = Interlaced video
txN_im_field Input
Video field
  • 0 = Bottom field (or progressive)
  • 1 = Top field
Table 24.  Video Interface (TX AXI4-Stream Video Interface)v is the number of bits per color, p is the pixels per clock (1 = single, 2 = dual, and 4 = quad).
Interface Port Type Clock Domain Port Direction Description
tx_axi4s_clk Clock N/A tx_axi4s_clk Input AXI4-stream video clock (300Mhz)
tx_axi4s_reset Reset tx_axi4s_clk tx_axi4s_reset Input AXI4-stream video reset
tx_axi4s_vid_in Conduit tx_axi4s_vid_in_tdata[(3v+7/8)*p*8-1:0] Input AXI4-stream video data
tx_axi4s_vid_in_tuser[(3v+7/8)*p-1:0] Input AXI4-stream video data start of frame
tx_axi4s_vid_in_tvalid Input AXI4-stream video data valid
tx_axi4s_vid_in_tready Output AXI4-stream video data ready
tx_axi4s_vid_in_tlast Input AXI4-stream video data end of line
Table 25.  AUX Interface

Interface

Port Type

Clock Domain

Port

Direction

Description

aux_clk

Clock

N/A

aux_clk Input

AUX channel clock

aux_reset

Reset

aux_clk aux_reset Input

Active-high AUX channel reset

tx_aux

Conduit

aux_clk tx_aux_in Input

AUX channel data input

tx_aux_out Output

AUX channel data output

tx_aux_oe Output

Output buffer enable

tx_hpd Input

Hot plug detect

tx_aux_debug

AV-ST

aux_clk tx_aux_debug_data[31:0] Output

Formatted AUX channel debug data

tx_aux_debug_valid Output

Asserted when all the other signals on this port are valid

tx_aux_debug_sop Output

Start of packet (start of AUX request or reply)

tx_aux_debug_eop Output

End of packet (end of AUX request or reply)

tx_aux_debug_err Output

Asserted when an AUX channel bit error is detected

tx_aux_debug_cha Output

The channel number for data being transferred on the current cycle. Used as AUX channel data direction.

0 = Reply (from DisplayPort sink)

1 = Request (to DisplayPort sink)

AUX Interface

Table 26.  Secondary Interface N is the stream number; for example, tx_ss represents Stream 0, tx1_ss represents Stream 1, and so on.

Interface

Signal Type

Clock Domain

Port

Direction

Description

tx_ss_clk

Clock

N/A

tx_ss_clk Output

TX transceiver clock out and clock for secondary stream

Secondary Stream

(txN_ss)

AV-ST

tx_ss_clk txN_ss_data[127:0] Input

Secondary stream interface

txN_ss_valid Input
txN_ss_ready Output
txN_ss_sop Input
txN_ss_eop Input

Secondary Stream Interface 

Table 27.  Audio Interface m is the number of TX audio channels. N is the stream number; for example, tx_audio represents Stream 0, tx1_audio represents Stream 1, and so on.

Interface

Signal Type

Clock Domain

Port

Direction

Description

Audio

(txN_audio)

Clock N/A txN_audio_clk Input Audio clock
Conduit txN_audio_clk txN_audio_lpcm_data [m*32-1:0] Input

m channels of 32-bit audio sample data.

txN_audio_valid Input

Must be asserted when valid data is available on txN_audio_lpcm_data

txN_audio_mute Input

Must be asserted when audio is muted

Audio Interface

Table 28.  TX Transceiver Interface n is the number of TX lanes, s is the number of DisplayPort 1.4 symbols per clock. For any link rates equal to or below UHBR10, w = n * s * 10. For link rates above UHBR10, w = 64.
Note: Connect the DisplayPort signals to the Native PHY signals of the same name.

Interface

Port Type

Clock Domain

Port

Direction

Description

TX transceiver interface Clock N/A tx_std_clkout Input TX transceiver clock out.

Equivalent to Link Speed Clock (ls_clk).

All lanes on this interface use a single clock, sourced from DisplayPort Lane 0

Conduit tx_std_clkout tx_parallel_data[w–1:0] Output Parallel data for TX transceiver
Conduit N/A tx_pll_powerdown Output PLL power down for TX transceiver
Conduit xcvr_mgmt_clk tx_digitalreset[n–1:0] Output Resets the digital TX portion of TX transceiver
Note: Required only for Arria V, Cyclone V, and Stratix V devices.
Conduit N/A tx_analogreset[n–1:0] Output Resets the analog TX portion of TX transceiver
Note: Required only for Arria V, Cyclone V, and Stratix V devices.
Conduit N/A tx_cal_busy[n–1:0] Input Calibration in progress signal from TX transceiver
Conduit N/A tx_pll_locked Input PLL locked signal from TX transceiver
Table 29.  HDCP InterfaceApplicable only when you turn on the Support HDCP 2.3 or Support HDCP 1.3 parameters.

Interface

Port Type

Clock Domain

Port

Direction

Description

HDCP Clocks (hdcp_clks) Reset hdcp_reset Input Main asynchronous reset for HDCP.
Clock csr_clk Input

HDCP clock for control and status registers.

Typically, shares the Nios II processor clock (100 MHz).

crypto_clk Input

HDCP 2.3 clock for authentication and cryptographic layer.

You can use any clock with a frequency of up to 200 MHz.

Not applicable for HDCP 1.3.

Note: The clock frequency determines the authentication latency.
CSR Interface (tx_csr) Avalon-MM csr_clk tx_csr_addr[7:0] Input

The Avalon-MM slave port that provides access to internal control and status register, mainly for authentication messages transfer. This interface is expected to operate at Nios II processor clock domain.

Because of the extremely large bit portion of message, the IP transfers the message in burst mode with full handshaking mechanism.

Write transfers always have a wait time of 0 cycle while read transfers have a wait time of 1 cycle.

The addressing should be accessed as word addressing in the Platform Designer flow. For example, addressing of 4 in the Nios II software selects the address of 1 in the slave.

tx_csr_wr Input
tx_csr_rd Input
tx_csr_wrdata[31:0] Input
tx_csr_rddata[31:0] Output
HDCP Key and Status Interface (tx_hdcp) Conduit (Key) crypto_clk tx_kmem_wait[0] (HDCP 2.3)

tx_kmem_wait[1] (HDCP 1.3)

Input

Always keep this signal asserted until the key is ready to be read.

This signal is not available if you turn on the Support HDCP Key Management parameter.

tx_kmem_rdaddr[3:0] (HDCP 2.3)

tx_kmem_rdaddr[9:4] (HDCP 1.3)

Output

Key read address bus.

[3:2] = Reserved.

This signal is not available if you turn on the Support HDCP Key Management parameter.

tx_kmem_q[31:0] (HDCP 2.3)

tx_kmem_q[87:32] (HDCP 1.3)

Input

Key data for read transfers.

Read transfer always have a wait time of 1 cycle.

This signal is not available if you turn on the Support HDCP Key Management parameter.

Avalon-MM csr_clk tx_hdcp1_kmem_wr Input

The Avalon® memory-mapped slave port provides write access to internal HDCP 1.3 key storage.

Write transfers always have a wait time of 0.

The Avalon® memory-mapped master access the addressing as word addressing in the Platform Designer flow.

For example, addressing of 4 in the Avalon® memory-mapped master selects the address of 1 in the slave.

These signals are only available if you turn on the Support HDCP Key Management parameter and the Support HDCP 1.3 parameter.

tx_hdcp1_kmem_wrdata[31:0] Input
tx_hdcp1_kmem_addr[6:0] Input
Avalon-MM csr_clk tx_hdcp2_kmem_wr Input

The Avalon® memory-mapped slave port provides write access to internal HDCP 2.3 key storage.

Write transfers always have a wait time of 0.

The Avalon® memory-mapped master access the addressing as word addressing in the Platform Designer flow.

For example, addressing of 4 in the Avalon® memory-mapped master selects the address of 1 in the slave.

These signals are only available if you turn on the Support HDCP Key Management parameter and the Support HDCP 2.3 parameter.

tx_hdcp2_kmem_wrdata[31:0] Input
tx_hdcp2_kmem_addr[3:0] Input
Conduit tx_std_clkout[0] tx_hdcp1_enabled Output This signal is asserted by the IP if the outgoing video and secondary data are HDCP 1.3 encrypted.
tx_hdcp2_enabled Output This signal is asserted by the IP if the outgoing video and secondary data are HDCP 2.3 encrypted.
csr_clk tx_hdcp1_disable Input Assert this signal to disable the HDCP 1.3 IP.
Note: You must reset the HDCP IP (hdcp_reset) after toggling this signal. You must not call the software API hdcp_main() while this signal is asserted. You must call the software API hdcp_unauth() after deasserting this signal.
tx_hdcp2_disable Input Assert this signal to disable the HDCP 2.3 IP.
Note: You must reset the HDCP IP (hdcp_reset) after toggling this signal. You must not call the software API hdcp_main() while this signal is asserted. You must call the software API hdcp_unauth() after deasserting this signal.

Transceiver Reconfiguration Interface