Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide

Download PDF
ID 683704
Date 10/02/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. CvP Description 3. CvP Topologies 4. Design Considerations 5. CvP Driver and Registers 6. Understanding the Design Steps for CvP Initialization and Update Mode in Stratix® 10 7. Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide Archives 8. Document Revision History
1. Overview x
1.1. Benefits of Using CvP 1.2. CvP System 1.3. CvP Modes
1.3. CvP Modes x
1.3.1. CvP Limitations and Restrictions
1.3.1. CvP Limitations and Restrictions x
1.3.1.1. CvP Error Recovery
2. CvP Description x
2.1. Configuration Images 2.2. CvP Modes 2.3. Compression Features 2.4. Pin Description
2.2. CvP Modes x
2.2.1. CvP Initialization Mode 2.2.2. CvP Update Mode
3. CvP Topologies x
3.1. Single Endpoint 3.2. Multiple Endpoints
4. Design Considerations x
4.1. Designing CvP for an Open System 4.2. Designing CvP for a Closed System
4.1. Designing CvP for an Open System x
4.1.1. FPGA Power Supplies Ramp Time Requirement 4.1.2. PCIe* Wake-Up Time Requirement
4.1.2. PCIe* Wake-Up Time Requirement x
4.1.2.1. For CvP Initialization Mode 4.1.2.2. For CvP Update Mode
5. CvP Driver and Registers x
5.1. CvP Driver Support 5.2. CvP Driver Flow 5.3. VSEC Registers for CvP
5.3. VSEC Registers for CvP x
5.3.1. Vendor Specific Capability Header Register 5.3.2. Vendor Specific Header Register 5.3.3. Intel Marker Register 5.3.4. User Configurable Device/Board ID Register 5.3.5. CvP Status Register 5.3.6. CvP Mode Control Register 5.3.7. CvP Data Registers 5.3.8. CvP Programming Control Register 5.3.9. CvP Credit Register
6. Understanding the Design Steps for CvP Initialization and Update Mode in Stratix® 10 x
6.1. Implementation of CvP Initialization Mode 6.2. Implementation of CvP Update Mode
6.1. Implementation of CvP Initialization Mode x
6.1.1. Generating the Synthesis HDL files for Avalon® Streaming Stratix® 10 Hard IP for PCI Express 6.1.2. Setting up the CvP Parameters in Device and Pin Options 6.1.3. Compiling the Design 6.1.4. Converting the SOF File 6.1.5. Bringing up the Hardware
6.1.5. Bringing up the Hardware x
6.1.5.1. Installing the Upstream Open Source CvP Driver in Linux Systems 6.1.5.2. Modifying MSEL/DIP switch on Stratix® 10 FPGA Development Kit 6.1.5.3. Programming CvP Images
6.2. Implementation of CvP Update Mode x
6.2.1. Instantiating the PCIe* Hard IP 6.2.2. Setting Up the CvP Parameters 6.2.3. Setting up the Base Revision 6.2.4. Setting up and Compile the Updated Revision 6.2.5. Converting the SOF file of the Updated Revision 6.2.6. Programming the Core RBF file from the Updated Revision via PCIe Link
6.2.3. Setting up the Base Revision x
6.2.3.1. Creating a Reserved Core Partition 6.2.3.2. Defining a Logic Lock Region 6.2.3.3. Compiling and Exporting the Root Partition
1. Overview
2. CvP Description
3. CvP Topologies
4. Design Considerations
5. CvP Driver and Registers
6. Understanding the Design Steps for CvP Initialization and Update Mode in Stratix® 10
7. Stratix® 10 Configuration via Protocol (CvP) Implementation User Guide Archives
8. Document Revision History

5.3.5. CvP Status Register

Table 9.  CvP Status Register (Byte Offset: 0xB9E)
Bits Name Reset Value Access Description
[15:11] — Variable RO Reserved.
[10] CVP_CONFIG_SUCCESS Variable RO Status bit set by the device to indicate that the core image configuration was successful.
[9] — Variable RO Reserved.
[8] PLD_CLK_IN_USE Variable RO

From clock switch module to fabric. You can use this bit for debug.
[7] CVP_CONFIG_DONE Variable RO

Indicates that the device has completed the device configuration via CvP and there were no errors.

[6] — Variable RO Reserved.
[5] USERMODE Variable RO Indicates if the configurable FPGA fabric is in user mode.
[4] CVP_EN Variable RO Indicates if the device has enabled CvP mode.
[3] CVP_CONFIG_ERROR Variable RO Reflects the value of this signal from the device, checked by software to determine if there was an error during configuration.
[2] CVP_CONFIG_READY 0x0 RO

Reflects the value of this signal from the device, checked by software during programming algorithm to determine the device is ready for configuration.

[1:0] — Variable RO Reserved.
Level Two Title