Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

Download PDF
ID 683426
Date 4/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. About LL Ethernet 10G MAC 2. Getting Started 3. LL Ethernet 10G MAC Intel® FPGA IP Design Examples 4. Functional Description 5. Configuration Registers 6. Interface Signals 7. Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide Archives 8. Document Revision History for the Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide
1. About LL Ethernet 10G MAC x
1.1. Features 1.2. Release Information 1.3. Low Latency Ethernet 10G MAC Operating Modes 1.4. Device Family Support 1.5. Performance and Resource Utilization
1.1. Features x
1.1.1. LL Ethernet 10G MAC and Legacy 10-Gbps Ethernet MAC
1.5. Performance and Resource Utilization x
1.5.1. Resource Utilization 1.5.2. TX and RX Latency
2. Getting Started x
2.1. Introduction to Intel® FPGA IP Cores 2.2. Installing and Licensing Intel® FPGA IP Cores 2.3. Specifying the IP Core Parameters and Options ( Quartus® Prime Pro Edition) 2.4. IP Core Generation Output ( Quartus® Prime Pro Edition) 2.5. Files Generated for Intel IP Cores (Legacy Parameter Editor) 2.6. Simulating Intel® FPGA IP Cores 2.7. Creating a Signal Tap Debug File to Match Your Design Hierarchy 2.8. Parameter Settings for the Low Latency Ethernet 10G MAC Intel® FPGA IP Core 2.9. Upgrading the Low Latency Ethernet 10G MAC Intel® FPGA IP Core 2.10. Design Considerations for the Low Latency Ethernet 10G MAC Intel® FPGA IP Core
2.10. Design Considerations for the Low Latency Ethernet 10G MAC Intel® FPGA IP Core x
2.10.1. Migrating from Legacy Ethernet 10G MAC to LL Ethernet 10G MAC 2.10.2. Timing Constraints 2.10.3. Jitter on PLL Clocks
2.10.1. Migrating from Legacy Ethernet 10G MAC to LL Ethernet 10G MAC x
2.10.1.1. Migration—32-bit Datapath on Avalon® Streaming Interface 2.10.1.2. Migration—Maintains 64-bit on Avalon® Streaming Interface
2.10.2. Timing Constraints x
2.10.2.1. Pseudo-Static CSR Fields 2.10.2.2. Clock Crosser 2.10.2.3. Dual Clock FIFO
3. LL Ethernet 10G MAC Intel® FPGA IP Design Examples x
3.1. LL Ethernet 10G MAC Intel® FPGA IP Design Example for Stratix® 10 Devices 3.2. LL Ethernet 10G MAC Intel® FPGA IP Design Example for Arria® 10 Devices 3.3. LL Ethernet 10G MAC Intel® FPGA IP Design Example for Cyclone® 10 GX Devices
4. Functional Description x
4.1. Architecture 4.2. Interfaces 4.3. Frame Types 4.4. TX Datapath 4.5. RX Datapath 4.6. Flow Control 4.7. Reset Requirements 4.8. Supported PHYs 4.9. XGMII Error Handling (Link Fault) 4.10. IEEE 1588v2
4.4. TX Datapath x
4.4.1. Padding Bytes Insertion 4.4.2. Address Insertion 4.4.3. CRC-32 Insertion 4.4.4. XGMII Encapsulation 4.4.5. Inter-Packet Gap Generation and Insertion 4.4.6. XGMII Transmission 4.4.7. Unidirectional Feature 4.4.8. TX Timing Diagrams
4.5. RX Datapath x
4.5.1. XGMII Decapsulation 4.5.2. CRC Checking 4.5.3. Address Checking 4.5.4. Frame Type Checking 4.5.5. Length Checking 4.5.6. CRC and Padding Bytes Removal 4.5.7. Overflow Handling 4.5.8. RX Timing Diagrams
4.5.5. Length Checking x
4.5.5.1. Frame Length 4.5.5.2. Payload Length
4.6. Flow Control x
4.6.1. IEEE 802.3 Flow Control 4.6.2. Priority-Based Flow Control
4.6.1. IEEE 802.3 Flow Control x
4.6.1.1. Pause Frame Reception 4.6.1.2. Pause Frame Transmission
4.6.2. Priority-Based Flow Control x
4.6.2.1. PFC Frame Reception 4.6.2.2. PFC Frame Transmission
4.8. Supported PHYs x
4.8.1. 10GBASE-R Register Mode
4.10. IEEE 1588v2 x
4.10.1. Architecture 4.10.2. TX Datapath 4.10.3. RX Datapath 4.10.4. Frame Format
4.10.4. Frame Format x
4.10.4.1. PTP Packet in IEEE 802.3 4.10.4.2. PTP Packet over UDP/IPv4 4.10.4.3. PTP Packet over UDP/IPv6
5. Configuration Registers x
5.1. Register Map 5.2. Register Access Definition 5.3. Primary MAC Address 5.4. MAC Reset Control Register 5.5. TX Configuration and Status Registers 5.6. Flow Control Registers 5.7. Unidirectional Control Registers 5.8. RX Configuration and Status Registers 5.9. Timestamp Registers 5.10. ECC Registers 5.11. Statistics Registers
5.1. Register Map x
5.1.1. Mapping 10-Gbps Ethernet MAC Registers to LL Ethernet 10G MAC Registers
5.9. Timestamp Registers x
5.9.1. Calculating Timing Adjustments
6. Interface Signals x
6.1. Clock and Reset Signals 6.2. Speed Selection Signal 6.3. Error Correction Signals 6.4. Unidirectional Signals 6.5. Avalon® Memory-Mapped Interface Programming Signals 6.6. Avalon® Streaming Data Interfaces 6.7. Avalon® Streaming Flow Control Signals 6.8. Avalon® Streaming Status Interface 6.9. PHY-side Interfaces 6.10. IEEE 1588v2 Interfaces
6.6. Avalon® Streaming Data Interfaces x
6.6.1. Avalon® Streaming TX Data Interface Signals 6.6.2. Avalon® Streaming RX Data Interface Signals 6.6.3. Avalon® Streaming Data Interface Clocks
6.8. Avalon® Streaming Status Interface x
6.8.1. Avalon® Streaming Interface TX Status Signals 6.8.2. Avalon® Streaming Interface RX Status Signals
6.9. PHY-side Interfaces x
6.9.1. XGMII TX Signals 6.9.2. XGMII RX Signals 6.9.3. GMII TX Signals 6.9.4. GMII RX Signals 6.9.5. MII TX Signals 6.9.6. MII RX Signals
6.10. IEEE 1588v2 Interfaces x
6.10.1. IEEE 1588v2 Egress TX Signals 6.10.2. IEEE 1588v2 Ingress RX Signals 6.10.3. IEEE 1588v2 Interface Clocks
1. About LL Ethernet 10G MAC
2. Getting Started
3. LL Ethernet 10G MAC Intel® FPGA IP Design Examples
4. Functional Description
5. Configuration Registers
6. Interface Signals
7. Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide Archives
8. Document Revision History for the Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

4.8.1. 10GBASE-R Register Mode

The MAC IP core supports this feature for use with the Arria® 10, Cyclone® 10 GX, and Stratix® 10 Transceiver Native PHY IP core preset configurations. When operating in this mode, the round-trip latency for the MAC and PHY is reduced to 140 ns (for Arria® 10 and Cyclone® 10 GX devices) or 168 ns (for Stratix® 10 devices) with a slight increase in resource count and clock frequencies.

When you enable this feature, the MAC IP core implements two additional signals to determine the validity of the data on the TX and RX XGMII. These signals, xgmii_tx_valid and xgmii_rx_valid, ensure that the effective data rate of the MAC is 10 Gbps. You must also observe the following guidelines when using the register mode:

  • For Arria® 10 and Cyclone® 10 GX devices, the selected preset is 10GBASE-R Register Mode.
  • For Stratix® 10 devices, the selected preset is 10GBASE-R 1588.
  • The PHY must expose the TX and RX parallel clocks.
  • The PHY must expose data valid signals, with MAC/PHY TX/RX interfaces in register mode, as in the IEEE 1588v2 configuration.
  • The MAC and PHY run at the parallel clock frequency of 322.265625 MHz (the PCS/PMA width equals to 32).
Figure 26. PHY Configuration with 10GBASE-R Register Mode Enabled for Arria® 10 and Cyclone® 10 GX Devices


Figure 27. PHY Configuration with 10GBASE-R with IEEE 1588v2 Enabled for Stratix® 10 Devices
Related Information
Level Two Title