Arria V GZ Avalon-ST Interface for PCIe Solutions: User Guide

ID 683297
Date 12/21/2020
Public
Document Table of Contents

5.14.3. PIPE Interface Signals

These PIPE signals are available for Gen1, Gen2, and Gen3 variants so that you can simulate using either the serial or the PIPE interface. Simulation is much faster using the PIPE interface because the PIPE simulation bypasses the SERDES model . By default, the PIPE interface data width is 8 bits for Gen1 and Gen2 and 32 bits for Gen3. You can use the PIPE interface for simulation even though your actual design includes a serial interface to the internal transceivers. However, it is not possible to use the Hard IP PIPE interface in hardware, including probing these signals using Signal Tap.

Intel® Cyclone® 10 GX devices do not support the Gen3 data rate.

Note: The Intel Root Port BFM bypasses Gen3 Phase 2 and Phase 3 Equalization. However, Gen3 variants can perform Phase 2 and Phase 3 equalization if instructed by a third-party BFM.
Table 45.  PIPE Interface Signals

Signal

Direction

Description

txdata0[7:0]

Output

Transmit data <n>. This bus transmits data on lane <n>.

txdatak0

Output

Transmit data control <n>. This signal serves as the control bit for txdata <n>.

txblkst0

Output

For Gen3 operation, indicates the start of a block in the transmit direction.

txcompl0

Output

Transmit compliance <n>. This signal forces the running disparity to negative in Compliance Mode (negative COM character).

txdataskip0

Output

For Gen3 operation. Allows the MAC to instruct the TX interface to ignore the TX data interface for one clock cycle. The following encodings are defined:

  • 1’b0: TX data is invalid
  • 1’b1: TX data is valid
txdeemph0

Output

Transmit de-emphasis selection. The Intel® Arria® 10 Hard IP for PCI Express sets the value for this signal based on the indication received from the other end of the link during the Training Sequences (TS). You do not need to change this value.

txdetectrx0

Output

Transmit detect receive <n>. This signal tells the PHY layer to start a receive detection operation or to begin loopback.

txelecidle0

Output

Transmit electrical idle <n>. This signal forces the TX output to electrical idle.

txswing

Output

When asserted, indicates full swing for the transmitter voltage. When deasserted indicates half swing.

txmargin[2:0]

Output

Transmit VOD margin selection. The value for this signal is based on the value from the Link Control 2 Register. Available for simulation only.

txsynchd0[1:0]

Output

For Gen3 operation, specifies the transmit block type. The following encodings are defined:

  • 2'b01: Ordered Set Block
  • 2'b10: Data Block
Designs that do not support Gen3 can let this signal float.

rxdata0[7:0]

Input

Receive data <n>. This bus receives data on lane <n>.

rxdatak0

Input

Receive data <n>. This bus receives data on lane <n>. Bit 0 corresponds to the lowest-order byte of rxdata, and so on. A value of 0 indicates a data byte. A value of 1 indicates a control byte. For Gen1 and Gen2 only.

rxblkst0

Input

For Gen3 operation, indicates the start of a block in the receive direction.

rxdataskip0

Output

For Gen3 operation. Allows the PCS to instruct the RX interface to ignore the RX data interface for one clock cycle. The following encodings are defined:

  • 1’b0: RX data is invalid
  • 1’b1: RX data is valid

rxelecidle0

Input

Receive electrical idle <n>. When asserted, indicates detection of an electrical idle.

rxpolarity0

Output

Receive polarity <n>. This signal instructs the PHY layer to invert the polarity of the 8B/10B receiver decoding block.

rxstatus0[2:0]

Input

Receive status <n>. This signal encodes receive status, including error codes for the receive data stream and receiver detection.

rxsynchd0[1:0]

Input

For Gen3 operation, specifies the receive block type. The following encodings are defined:

  • 2'b01: Ordered Set Block
  • 2'b10: Data Block
Designs that do not support Gen3 can ground this signal.

rxvalid0

Input

Receive valid <n>. This signal indicates symbol lock and valid data on rxdata <n> and rxdatak <n>.

phystatus0

Input

PHY status <n>. This signal communicates completion of several PHY requests.

powerdown0[1:0]

Output

Power down <n>. This signal requests the PHY to change its power state to the specified state (P0, P0s, P1, or P2).

currentcoeff0[17:0]

Output

For Gen3, specifies the coefficients to be used by the transmitter. The 18 bits specify the following coefficients:

  • [5:0]: C-1
  • [11:6]: C0
  • [17:12]: C+1
currentrxpreset0[2:0]

Output

For Gen3 designs, specifies the current preset.

simu_mode_pipe

Input

When set to 1, the PIPE interface is in simulation mode.

sim_pipe_rate[1:0]

Output

The 2‑bit encodings have the following meanings:

  • 2’b00: Gen1 rate (2.5 Gbps)
  • 2’b01: Gen2 rate (5.0 Gbps)
  • 2’b10: Gen3 rate (8.0 Gbps)
sim_pipe_pclk_in

Input

This clock is used for PIPE simulation only, and is derived from the refclk. It is the PIPE interface clock used for PIPE mode simulation.

sim_pipe_pclk_out

Output

TX datapath clock to the BFM PHY. pclk_out is derived from refclk and provides the source synchronous clock for TX data from the PHY.

sim_pipe_clk250_out

Output

Used to generate pclk.

sim_pipe_clk500_out

Output

Used to generate pclk.

sim_pipe_ltssmstate0[4:0]

Input and Output

LTSSM state: The LTSSM state machine encoding defines the following states:

  • 5’b00000: Detect.Quiet
  • 5’b00001: Detect.Active
  • 5’b00010: Polling.Active
  • 5’b 00011: Polling.Compliance
  • 5’b 00100: Polling.Configuration
  • 5’b00101: Polling.Speed
  • 5’b00110: config.LinkwidthsStart
  • 5’b 00111: Config.Linkaccept
  • 5’b 01000: Config.Lanenumaccept
  • 5’b01001: Config.Lanenumwait
  • 5’b01010: Config.Complete
  • 5’b 01011: Config.Idle
  • 5’b01100: Recovery.Rcvlock
  • 5’b01101: Recovery.Rcvconfig
  • 5’b01110: Recovery.Idle
  • 5’b 01111: L0
  • 5’b10000: Disable
  • 5’b10001: Loopback.Entry
  • 5’b10010: Loopback.Active
  • 5’b10011: Loopback.Exit
  • 5’b10100: Hot.Reset
  • 5’b10101: L0s
  • 5’b11001: L2.transmit.Wake
  • 5’b11010: Recovery.Speed
  • 5’b11011: Recovery.Equalization, Phase 0
  • 5’b11100: Recovery.Equalization, Phase 1
  • 5’b11101: Recovery.Equalization, Phase 2
  • 5’b11110: Recovery.Equalization, Phase 3
  • 5’b11111: Recovery.Equalization, Done
rxfreqlocked0

Input

When asserted indicates that the pclk_in used for PIPE simulation is valid.

eidleinfersel0[2:0]

Output

Electrical idle entry inference mechanism selection. The following encodings are defined:

  • 3'b0xx: Electrical Idle Inference not required in current LTSSM state
  • 3'b100: Absence of COM/SKP Ordered Set in the 128 us window for Gen1 or Gen2
  • 3'b101: Absence of TS1/TS2 Ordered Set in a 1280 UI interval for Gen1 or Gen2
  • 3'b110: Absence of Electrical Idle Exit in 2000 UI interval for Gen1 and 16000 UI interval for Gen2
  • 3'b111: Absence of Electrical idle exit in 128 us window for Gen1