AN 955: Programmer’s Configuration Debugger Tool

Download PDF
ID 691274
Date 4/07/2025
Public
Document Table of Contents
Document Table of Contents x
1. Programmer’s Configuration Debugger Tool 2. Debugging Tool Components 3. Document Revision History for AN 955: Programmer’s Configuration Debugger Tool
1. Programmer’s Configuration Debugger Tool x
1.1. Launching Debugger Tool
2. Debugging Tool Components x
2.1. Parsing Programming Files 2.2. Getting Device Information 2.3. Debugging QSPI Flash 2.4. QSPI Controller Settings and SFDP Values 2.5. Debugging Remote System Update 2.6. Voltage Sensor Monitoring 2.7. Temperature Sensor Monitoring 2.8. Hard Processor System (HPS) Cold Reset 2.9. Debug Log 2.10. SDM Mailbox Command 2.11. VR Diagnostic 2.12. VR Telemetry
2.1. Parsing Programming Files x
2.1.1. Reading Programming File Information 2.1.2. Parsing Program Files Command Option 2.1.3. Programming File Formats
2.1.3. Programming File Formats x
2.1.3.1. SOF File Information 2.1.3.2. RBF File Information 2.1.3.3. PMSF File Information 2.1.3.4. JIC File Information 2.1.3.5. RPD File Information 2.1.3.6. POF File Information
2.2. Getting Device Information x
2.2.1. Reading Device Information from SDM-Based Devices 2.2.2. Reading Device Information from Legacy Devices
2.3. Debugging QSPI Flash x
2.3.1. Performing QSPI Flash Debugging
2.4. QSPI Controller Settings and SFDP Values x
2.4.1. Reading the QSPI Controller Settings and SFDP Values
2.4.1. Reading the QSPI Controller Settings and SFDP Values x
2.4.1.1. QSPI Flash Debugging Use Cases
2.5. Debugging Remote System Update x
2.5.1. Performing Remote System Update Debugging
2.6. Voltage Sensor Monitoring x
2.6.1. Reading Voltage Measurement
2.7. Temperature Sensor Monitoring x
2.7.1. Reading Temperature Measurement
2.8. Hard Processor System (HPS) Cold Reset x
2.8.1. Performing Hard Processor System (HPS) Cold Reset
2.9. Debug Log x
2.9.1. Getting the Debug Log
2.10. SDM Mailbox Command x
2.10.1. Sending SDM Mailbox Command 2.10.2. Command Options for Sending SDM Mailbox Command
2.11. VR Diagnostic x
2.11.1. Performing VR Diagnostic
2.12. VR Telemetry x
2.12.1. Performing VR Telemetry
1. Programmer’s Configuration Debugger Tool
2. Debugging Tool Components
3. Document Revision History for AN 955: Programmer’s Configuration Debugger Tool

2.11.1. Performing VR Diagnostic

Perform the VR diagnostic test by following the steps below.
  1. Click Hardware Setup and select the hardware setup to use for debugging.
  2. Click Load Device and select your device.
  3. Click Power Management tab.
    Note: The Power Management tab is disabled if the selected device is not SDM-based.
  4. Click VR Diagnostic.
  5. Click Select All VR Diagnostic Test(s) to select all tests. To run specific tests, click the checkboxes for the tests you want to run.
    Note: To run VADC crosscheck tests, the device must not be in user mode. VADC crosscheck tests are not supported in user mode and are disabled when the device enters user mode.
  6. Click Run Selected Test(s) to perform all the selected tests.
  7. Click Load Last Test Result to load the results of the last executed test.
    • Passing tests are in green and with a checkmark symbol.
    • Failing tests are in red and with an X symbol.
    • Unsupported tests are in yellow with a question mark symbol.
  8. Click Clear to reset the test selection and results.
Figure 15. VR Diagnostic Results
Related Information
Level Two Title