AN 955: Programmer’s Configuration Debugger Tool

Download PDF
ID 691274
Date 9/29/2025
Public
Document Table of Contents
Document Table of Contents x
1. Programmer’s Configuration Debugger Tool 2. Debugging Tool Components 3. Document Revision History for AN 955: Programmer’s Configuration Debugger Tool
1. Programmer’s Configuration Debugger Tool x
1.1. Launching the Debugger Tool
2. Debugging Tool Components x
2.1. Parsing Programming Files 2.2. Getting Device Information 2.3. Debugging QSPI Flash 2.4. QSPI Controller Settings and SFDP Values 2.5. Debugging Remote System Update 2.6. Voltage Sensor Monitoring 2.7. Temperature Sensor Monitoring 2.8. Hard Processor System (HPS) Cold Reset 2.9. Debug Log 2.10. SDM Mailbox Command 2.11. VR Diagnostic 2.12. VR Telemetry 2.13. Virtual Hardware
2.1. Parsing Programming Files x
2.1.1. Reading Programming File Information 2.1.2. Parsing Program Files Command Option 2.1.3. Programming File Formats
2.1.3. Programming File Formats x
2.1.3.1. SOF File Information 2.1.3.2. RBF File Information 2.1.3.3. PMSF File Information 2.1.3.4. JIC File Information 2.1.3.5. RPD File Information 2.1.3.6. POF File Information
2.2. Getting Device Information x
2.2.1. Reading Device Information from SDM-Based Devices 2.2.2. Reading Device Information from Legacy Devices
2.3. Debugging QSPI Flash x
2.3.1. Performing QSPI Flash Debugging
2.4. QSPI Controller Settings and SFDP Values x
2.4.1. Reading the QSPI Controller Settings and SFDP Values
2.4.1. Reading the QSPI Controller Settings and SFDP Values x
2.4.1.1. QSPI Flash Debugging Use Cases
2.5. Debugging Remote System Update x
2.5.1. Performing Remote System Update Debugging
2.6. Voltage Sensor Monitoring x
2.6.1. Reading Voltage Measurement
2.7. Temperature Sensor Monitoring x
2.7.1. Reading Temperature Measurement
2.8. Hard Processor System (HPS) Cold Reset x
2.8.1. Performing Hard Processor System (HPS) Cold Reset
2.9. Debug Log x
2.9.1. Getting the Debug Log
2.10. SDM Mailbox Command x
2.10.1. Sending SDM Mailbox Command 2.10.2. Command Options for Sending SDM Mailbox Command
2.11. VR Diagnostic x
2.11.1. Performing VR Diagnostic
2.12. VR Telemetry x
2.12.1. Performing VR Telemetry
2.13. Virtual Hardware x
2.13.1. Virtual Hardware Expected Behavior 2.13.2. Accessing Virtual Hardware
2.13.2. Accessing Virtual Hardware x
2.13.2.1. Reading Programming File Information from Virtual Hardware 2.13.2.2. Reading Device Information from Virtual Hardware 2.13.2.3. Accessing Flash Memory Attached to Virtual Hardware 2.13.2.4. Performing RSU with Virtual Hardware 2.13.2.5. Reading Voltage Sensor Measurement from Virtual Hardware 2.13.2.6. Reading Temperature Sensor Measurement from Virtual Hardware 2.13.2.7. Sending SDM Mailbox Commands with Virtual Hardware
1. Programmer’s Configuration Debugger Tool
2. Debugging Tool Components
3. Document Revision History for AN 955: Programmer’s Configuration Debugger Tool

2.5. Debugging Remote System Update

You can debug the RSU feature through the debugger tool GUI. Triggering reconfiguration of the factory image or an application image is supported. Connect the device to the debugger tool via the JTAG interface to enable the debugging. Then, configure the device with a RSU image to debug the RSU related issues.

The debugger tool allows to debug RSU related issues that include:
  • Trigger reconfiguration of an image at specified start address.
  • Read the application image addresses from the sub-partition table and configuration pointer block.
  • Display the source, location, messages, and details of the error.
  • Read current image and failing image addresses from RSU status.
  • Clear the current image retry counter and error log status information.

Section Content
Performing Remote System Update Debugging

Level Two Title