Ethernet Toolkit User Guide

Download PDF
ID 683793
Date 4/28/2025
Public
Document Table of Contents
Document Table of Contents x
1. Ethernet Toolkit Overview 2. Setting up the Ethernet Toolkit 3. Functional Description 4. Document Revision History for the Ethernet Toolkit User Guide
1. Ethernet Toolkit Overview x
1.1. Features 1.2. Supported Ethernet IP Cores and Devices
2. Setting up the Ethernet Toolkit x
2.1. System Requirements and Prerequisites 2.2. Running the Ethernet Toolkit
2.1. System Requirements and Prerequisites x
2.1.1. System Requirements 2.1.2. Enabling your Design for the Ethernet Toolkit
3. Functional Description x
3.1. Ethernet Toolkit Groups and Tabs 3.2. Link Bring Up Guidelines 3.3. Ethernet Toolkit Multirate Support 3.4. Ethernet Toolkit Subsystem Support 3.5. Ethernet Toolkit GTS Ethernet Hard IP Support
3.1. Ethernet Toolkit Groups and Tabs x
3.1.1. IP Configuration and Other Information 3.1.2. General Commands 3.1.3. Settings 3.1.4. Status 3.1.5. Statistics Counters 3.1.6. Testing Features
3.1.2. General Commands x
3.1.2.1. Loopback 3.1.2.2. Resets
3.1.4. Status x
3.1.4.1. Link Bring Up 3.1.4.2. PCS Status 3.1.4.3. PHY Status 3.1.4.4. MAC Settings 3.1.4.5. AN and LT Status
3.1.5. Statistics Counters x
3.1.5.1. Example Design Packet Generator Settings 3.1.5.2. Transmitter and Receiver Statistics 3.1.5.3. RS-FEC
3.1.5.1. Example Design Packet Generator Settings x
3.1.5.1.1. Packet Generator for E-, H-, and L-Tile Ethernet IPs 3.1.5.1.2. Packet Generator for F-Tile Ethernet IP
3.1.5.2. Transmitter and Receiver Statistics x
3.1.5.2.1. Effective Bandwidth Calculation
3.1.5.3. RS-FEC x
3.1.5.3.1. 32-Bit Soft CWBIN Counter Status
3.1.6. Testing Features x
3.1.6.1. Example Design PHY and Packet Generator Loopback Test 3.1.6.2. Read Register 3.1.6.3. Write to Register
3.2. Link Bring Up Guidelines x
3.2.1. Example Link Bring Up Using E-Tile Hard IP 3.2.2. Example Link Bring Up Using F-Tile Hard IP 3.2.3. Example Link Bring Up Using GTS Ethernet Hard IP
1. Ethernet Toolkit Overview
2. Setting up the Ethernet Toolkit
3. Functional Description
4. Document Revision History for the Ethernet Toolkit User Guide

3.2.1. Example Link Bring Up Using E-Tile Hard IP

This section covers an example of link bring up for the E-Tile Hard IP for Ethernet Intel® FPGA IP. Perform the following steps to establish Ethernet link:

If your design (.sof) instantiates Ethernet IP with Enable AN/LT parameter enabled in IP parameter editor:
  1. If you configure your IP in internal or external loopback, then turn on the Ignore Nonce parameter, and if you are using internal loopback, then turn on Enable Internal Loopback parameter.
  2. Click Reset AN/LT Sequencer in AN and LT status tab of the Ethernet Toolkit.
If your design (.sof) instantiates Ethernet IP with Enable AN/LT parameter disabled in IP parameter editor:
  • When you configure your IP in internal loopback:
    1. Turn on Enable Internal Loopback parameter.
    2. Turn on Initial Adaptation parameter.
  • When you configure your IP in external loopback or connect to a link partner:
    1. Choose a recipe from the PMA Adaptation Select option and click Apply.
    2. Click External Adaption button.
Level Two Title