Qsys System Design Tutorial

Download PDF
ID 683378
Date 5/04/2015
Public
Document Table of Contents
Document Table of Contents x
1. Qsys System Design Tutorial
1. Qsys System Design Tutorial x
1.1. Software and Hardware Requirements 1.2. Download and Install the Tutorial Design Files 1.3. Open the Tutorial Project 1.4. Creating Qsys Systems 1.5. Assemble a Hierarchical System 1.6. Viewing the Memory Tester System in Qsys 1.7. Compiling and Downloading Software to a Development Board 1.8. Debugging Your Design 1.9. Verifying Hardware in System Console 1.10. Simulating Custom Components 1.11. View a Diagram of the Completed System
1.4. Creating Qsys Systems x
1.4.1. Create a Data Pattern Generator Qsys System 1.4.2. Create a Data Pattern Checker Qsys System
1.4.1. Create a Data Pattern Generator Qsys System x
1.4.1.1. Create a New Qsys System and Set up the Clock Source 1.4.1.2. Add a Pipeline Bridge 1.4.1.3. Add a Custom Pattern Generator 1.4.1.4. Add a PRBS Pattern Generator 1.4.1.5. Add a Two-to-One Streaming Multiplexer 1.4.1.6. Verify the Memory Address Map 1.4.1.7. Connect the Reset Signals 1.4.1.8. Save the System
1.4.2. Create a Data Pattern Checker Qsys System x
1.4.2.1. Create a New Qsys System and Set Up the Clock Soource 1.4.2.2. Add a Pipeline Bridge 1.4.2.3. Add a Custom Pattern Checker 1.4.2.4. Add the PRBS Pattern Checker 1.4.2.5. Add a One-to-Two Streaming Demultiplexer 1.4.2.6. Verify the Memory Address Map 1.4.2.7. Connect the Reset Signals 1.4.2.8. Save the System
1.5. Assemble a Hierarchical System x
1.5.1. Create the Hierarchical Memory Tester System 1.5.2. Complete the Top-Level System
1.5.1. Create the Hierarchical Memory Tester System x
1.5.1.1. Add the Pattern Generator 1.5.1.2. Add the Pattern Checker 1.5.1.3. Add Memory Master Components 1.5.1.4. Connect the Reset Signals 1.5.1.5. Verify the Memory Address Map 1.5.1.6. Save the System
1.5.1.3. Add Memory Master Components x
1.5.1.3.1. Add a Pattern Writer Component 1.5.1.3.2. Add a Pattern Reader Component 1.5.1.3.3. Add a RAM Test Controller
1.9. Verifying Hardware in System Console x
1.9.1. Open the Tutorial Project 1.9.2. Add the JTAG-to-Avalon Master Bridge 1.9.3. Debug with System Console
1.10. Simulating Custom Components x
1.10.1. Generate a Testbench System in Qsys 1.10.2. Run Simulation In the ModelSim-Altera Software
1.10.1. Generate a Testbench System in Qsys x
1.10.1.1. Create a New Qsys System for the Design Under Test 1.10.1.2. Export Design Under Test 1.10.1.3. Generate a Testbench System 1.10.1.4. Generate Testbench System's Simulation Models
1.10.2. Run Simulation In the ModelSim-Altera Software x
1.10.2.1. Set Up the Simulation Environment 1.10.2.2. Run the Simulation
1. Qsys System Design Tutorial

1.5.1.1. Add the Pattern Generator

The custom pattern generator system provides a stream of pattern data via an Avalon-ST source interface. You control the system by accessing the memory locations allocated to each component within the subsystem. The system connects slave ports to a pipeline bridge, which it then exposes outside of the system.

The pattern generator system contains the following components:

  • Pipeline bridge
  • Custom pattern generator
  • PRBS pattern generator
  • Two-to-one streaming multiplexer
  • Streaming timing adapters
  1. In the IP Catalog, under Project expand System, and then double-click pattern_generator_system.
  2. In the parameter editor, click Finish to accept the default settings.
  3. Rename the instance to pattern_generator_subsystem.
  4. Set the pattern_generator_subsystem clk to clk_0.
  5. Connect the pattern_generator_subsystem slave interface to the mm_bridge m0 interface.
  6. Connect the pattern_generator_subsystem reset interface to the clk_0 clk_reset interface.
Level Two Title