Qsys System Design Tutorial

Download PDF
ID 683378
Date 5/04/2015
Public
Document Table of Contents
Document Table of Contents x
1. Qsys System Design Tutorial
1. Qsys System Design Tutorial x
1.1. Software and Hardware Requirements 1.2. Download and Install the Tutorial Design Files 1.3. Open the Tutorial Project 1.4. Creating Qsys Systems 1.5. Assemble a Hierarchical System 1.6. Viewing the Memory Tester System in Qsys 1.7. Compiling and Downloading Software to a Development Board 1.8. Debugging Your Design 1.9. Verifying Hardware in System Console 1.10. Simulating Custom Components 1.11. View a Diagram of the Completed System
1.4. Creating Qsys Systems x
1.4.1. Create a Data Pattern Generator Qsys System 1.4.2. Create a Data Pattern Checker Qsys System
1.4.1. Create a Data Pattern Generator Qsys System x
1.4.1.1. Create a New Qsys System and Set up the Clock Source 1.4.1.2. Add a Pipeline Bridge 1.4.1.3. Add a Custom Pattern Generator 1.4.1.4. Add a PRBS Pattern Generator 1.4.1.5. Add a Two-to-One Streaming Multiplexer 1.4.1.6. Verify the Memory Address Map 1.4.1.7. Connect the Reset Signals 1.4.1.8. Save the System
1.4.2. Create a Data Pattern Checker Qsys System x
1.4.2.1. Create a New Qsys System and Set Up the Clock Soource 1.4.2.2. Add a Pipeline Bridge 1.4.2.3. Add a Custom Pattern Checker 1.4.2.4. Add the PRBS Pattern Checker 1.4.2.5. Add a One-to-Two Streaming Demultiplexer 1.4.2.6. Verify the Memory Address Map 1.4.2.7. Connect the Reset Signals 1.4.2.8. Save the System
1.5. Assemble a Hierarchical System x
1.5.1. Create the Hierarchical Memory Tester System 1.5.2. Complete the Top-Level System
1.5.1. Create the Hierarchical Memory Tester System x
1.5.1.1. Add the Pattern Generator 1.5.1.2. Add the Pattern Checker 1.5.1.3. Add Memory Master Components 1.5.1.4. Connect the Reset Signals 1.5.1.5. Verify the Memory Address Map 1.5.1.6. Save the System
1.5.1.3. Add Memory Master Components x
1.5.1.3.1. Add a Pattern Writer Component 1.5.1.3.2. Add a Pattern Reader Component 1.5.1.3.3. Add a RAM Test Controller
1.9. Verifying Hardware in System Console x
1.9.1. Open the Tutorial Project 1.9.2. Add the JTAG-to-Avalon Master Bridge 1.9.3. Debug with System Console
1.10. Simulating Custom Components x
1.10.1. Generate a Testbench System in Qsys 1.10.2. Run Simulation In the ModelSim-Altera Software
1.10.1. Generate a Testbench System in Qsys x
1.10.1.1. Create a New Qsys System for the Design Under Test 1.10.1.2. Export Design Under Test 1.10.1.3. Generate a Testbench System 1.10.1.4. Generate Testbench System's Simulation Models
1.10.2. Run Simulation In the ModelSim-Altera Software x
1.10.2.1. Set Up the Simulation Environment 1.10.2.2. Run the Simulation
1. Qsys System Design Tutorial

1.4.1.2. Add a Pipeline Bridge

The components that make up the data pattern generator include several Avalon-MM slave interfaces. To allow a higher-level system to access the Avalon-MM slave interfaces by reading and writing to a single slave interface, you can consolidate the slave interfaces behind an Avalon-MM pipeline bridge, and export a single Avalon-MM slave interface out of the system.

To determine the required address width for a bridge, you must know the required addresses span of the other components in the system. Memory-mapped component interfaces outside the system address each interface in the system by specifying a memory offset value relative to the base address of the bridge.

A pipeline bridge can also improve system timing performance by optionally adding pipeline registers to the design.

  1. In the Library search box, type bridge to filter the component list and show only bridge components.
  2. Select Avalon-MM Pipeline Bridge, and then click Add.
  3. In the parameter editor, under Parameters, type 11 for the Address width.
    This width accommodates the memory span of all memory-mapped components behind the bridge in this system. As you add the other components in the system, you specify their base addresses within the span of the address space.
  4. Accept all other default settings, and then click Finish.
    The pipeline bridge is added to your system with the instance name mm_bridge_0.
  5. On the System Contents tab, right-click mm_bridge_0, click Rename, and then type mm_bridge.
  6. In the Clock column for the mm_bridge clk interface, select clk_0 from the list.
  7. To export the mm_bridge s0 interface, double-click the Export column, and then type slave.
Level Two Title