Intel® Cyclone® 10 GX CvP Initialization over PCI Express User Guide

Download PDF
ID 683358
Date 1/02/2018
Public
Document Table of Contents
Document Table of Contents x
1. CvP Initialization in Intel® Cyclone® 10 GX 2. Design Considerations for CvP Initialization in Intel® Cyclone® 10 GX 3. Understanding the Design Steps for CvP Initialization in Intel® Cyclone® 10 GX 4. CvP Driver and Registers A. Document Revision History for Intel® Cyclone® 10 GX CvP Initialization over PCI Express User Guide
1. CvP Initialization in Intel® Cyclone® 10 GX x
1.1. Benefits of Using CvP 1.2. CvP System 1.3. CvP Support for Intel® Cyclone® 10 GX Devices 1.4. CvP Initialization 1.5. CvP Compression and Encryption Features 1.6. CvP Pins
2. Design Considerations for CvP Initialization in Intel® Cyclone® 10 GX x
2.1. Designing CvP for an Open System 2.2. Designing CvP for a Closed System
3. Understanding the Design Steps for CvP Initialization in Intel® Cyclone® 10 GX x
3.1. Generating the Synthesis HDL Files for Intel® Cyclone® 10 GX PCI Express IP Core 3.2. Setting up the CvP Parameters in Device and Pin Options 3.3. Compiling the Design 3.4. Splitting the SOF File 3.5. Bringing up the Hardware
3.5. Bringing up the Hardware x
3.5.1. Installing Jungo WinDriver in Windows Systems 3.5.2. Installing Jungo WinDriver in Linux Systems 3.5.3. Modifying MSEL/DIP switch on Intel® Cyclone® 10 GX Dev-Kit 3.5.4. Programming CvP Images
4. CvP Driver and Registers x
4.1. CvP Driver Support 4.2. CvP Driver Flow 4.3. VSEC Registers for CvP
4.3. VSEC Registers for CvP x
4.3.1. Intel® -defined Vendor Specific Capability Header Register 4.3.2. Intel® -defined Vendor Specific Header Register 4.3.3. Intel® Marker Register 4.3.4. CvP Status Register 4.3.5. CvP Mode Control Register 4.3.6. CvP Data Registers 4.3.7. CvP Programming Control Register 4.3.8. Uncorrectable Internal Error Status Register 4.3.9. Uncorrectable Internal Error Mask Register 4.3.10. Correctable Internal Error Status Register 4.3.11. Correctable Internal Error Mask Register
1. CvP Initialization in Intel® Cyclone® 10 GX
2. Design Considerations for CvP Initialization in Intel® Cyclone® 10 GX
3. Understanding the Design Steps for CvP Initialization in Intel® Cyclone® 10 GX
4. CvP Driver and Registers
A. Document Revision History for Intel® Cyclone® 10 GX CvP Initialization over PCI Express User Guide

1.4. CvP Initialization

This scheme configures the core of the FPGA through the PCIe link upon system power up. Initialization refers to the initial fabric configuration image loaded in the FPGA fabric after power up.

Configuration Images

In CvP, you partition your design into two images: core image and periphery image.

You use the Intel® Quartus® Prime software to generate the following images:
  • Periphery image (*.periph.jic) — contains general purpose I/Os (GPIOs), I/O registers, the GCLK, QCLK, and RCLK clock networks, and logic that is implemented in hard IP such as the JTAG interface, PR block, CRC block, Oscillator block, Impedance control block, Chip ID, ASMI block, Remote update block, Temperature sensor, and Hard IP for PCI Express IP Core. These components are included in the periphery image because they are controlled by I/O periphery register bits. The entire periphery image is static and cannot be reconfigured.
  • Core image (*.core.rbf) — contains logic that is programmed by configuration RAM (CRAM). This image includes LABs, DSP, and embedded memory.

The periphery image is stored in an external configuration device and is loaded into the FPGA through the conventional configuration scheme. The core image is stored in a host memory and loaded into the FPGA through the PCIe link. All other periphery and core resources are frozen until the FPGA enters user mode.

After the periphery image configuration is complete, the CONF_DONE signal goes high and allows the FPGA to start PCIe link training. During PCIe link training, the FPGA is not in user mode. When PCIe link training is complete, the PCIe link transitions to L0 state and then through PCIe enumeration. The PCIe host then initiates the core image configuration through the PCIe link.

After the core image configuration is complete, the CvP_CONFDONE pin goes high, indicating the FPGA is fully configured.

After the FPGA is fully configured, the FPGA enters user mode. If the INIT_DONE signal is enabled, the INIT_DONE signal goes high after initialization is complete and the FPGA enters user mode.

In user mode, the PCIe links are available for normal PCIe applications.

Level Two Title