50 Gbps Ethernet IP Core User Guide

Download PDF
ID 683158
Date 5/08/2017
Public
Document Table of Contents
Document Table of Contents x
1. About the 50GbE Core 2. Getting Started 3. 50GbE Parameters 4. Functional Description 5. Reset 6. Interfaces and Signal Descriptions 7. Control and Status Register Descriptions 8. Debugging the Link 9. Document Revision History
1. About the 50GbE Core x
1.1. 50GbE Supported Features 1.2. 50GbE Core Device Family and Speed Grade Support 1.3. IP Core Verification 1.4. Performance and Resource Utilization
1.2. 50GbE Core Device Family and Speed Grade Support x
1.2.1. Device Family Support 1.2.2. 50GbE Core Device Speed Grade Support
1.3. IP Core Verification x
1.3.1. Simulation Environment 1.3.2. Compilation Checking 1.3.3. Hardware Testing
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IP Cores 2.2. Specifying the 50GbE Core Parameters and Options 2.3. Simulating the IP Core 2.4. Generated File Structure 2.5. Integrating Your IP Core in Your Design 2.6. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IP Cores x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating Your IP Core in Your Design x
2.5.1. Pin Assignments 2.5.2. Adding the Transceiver PLL 2.5.3. Handling Potential Jitter in Intel® Arria® 10 Devices 2.5.4. Placement Settings for the 50GbE Core
4. Functional Description x
4.1. 50GbE Core Functional Description 4.2. User Interface to Ethernet Transmission
4.1. 50GbE Core Functional Description x
4.1.1. 50GbE Core TX MAC Datapath 4.1.2. 50GbE Core RX MAC Datapath 4.1.3. Link Fault Signaling Interface 4.1.4. 50 GbE RX PCS
4.1.1. 50GbE Core TX MAC Datapath x
4.1.1.1. Frame Padding 4.1.1.2. Preamble Insertion 4.1.1.3. Inter-Packet Gap Generation and Insertion
4.1.2. 50GbE Core RX MAC Datapath x
4.1.2.1. IP Core Preamble Processing 4.1.2.2. IP Core Strict SFD Checking 4.1.2.3. IP Core Malformed Packet Handling 4.1.2.4. Length/Type Field Processing 4.1.2.5. RX CRC Checking and Dynamic Forwarding
4.1.2.4. Length/Type Field Processing x
4.1.2.4.1. Length Checking
4.2. User Interface to Ethernet Transmission x
4.2.1. Order of Transmission 4.2.2. Bit Order For TX and RX Datapaths
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. Transceivers 6.4. Transceiver Reconfiguration Signals 6.5. Avalon® Memory-Mapped Management Interface 6.6. Miscellaneous Status and Debug Signals 6.7. Reset Signals
7. Control and Status Register Descriptions x
7.1. PHY Registers 7.2. TX MAC Registers 7.3. RX MAC Registers
1. About the 50GbE Core
2. Getting Started
3. 50GbE Parameters
4. Functional Description
5. Reset
6. Interfaces and Signal Descriptions
7. Control and Status Register Descriptions
8. Debugging the Link
9. Document Revision History

7.2. TX MAC Registers

Table 20.  TX MAC Registers
Addr Name Description Reset Access
0x400 TXMAC_REVID

TX MAC revision ID for 50G TX MAC CSRs.

0x0916 2016

 RO
0x401 TXMAC_SCRATCH Scratch register available for testing. 0x0000 0000 RW
0x402 TXMAC_NAME_0

First 4 characters of IP core variation identifier string, "50gMACTxCSR".

0x3530 674D

RO
0x403 TXMAC_NAME_1

Next 4 characters of IP core variation identifier string, "ACTx".

0x4143 5278 0x4143 5478

RO
0x404 TXMAC_NAME_2 Final 4 characters of IP core variation identifier string, "0CSR". The "0" is unprintable. 0x0043 5352

RO
0x405 LINK_FAULT

Link Fault Configuration Register. The following bits are defined:

  • Force Remote Fault bit[3]: When link fault generation is enabled, stops data transmission and forces transmission of a remote fault.
  • Disable Remote Fault bit[2]: When both link fault reporting and unidirectional transport are enabled, the core transmits data and does not transmit remote faults (RF). This bit takes effect when the value of this register is 28'hX4'b0111.
  • Unidir Enable bit[1]: When asserted, the core includes Clause 66 support for the remote link fault reporting on the Ethernet link.
  • Link Fault Reporting Enable bit[0]: The following encodings are defined:
    • 1'b1: The PCS generates the proper fault sequence on Ethernet link, when conditions are met.
    • 1'b0: The PCS does not generate the fault sequence.
28'hX_4'b0001 3

RW
0x406 IPG_COL_REM Specifies the number of IDLE columns to be removed in every Alignment Marker period to compensate for alignment marker insertion. You can program this register to a larger value than the default value, for clock compensation.

Bits [31:8] of this register are Reserved.

0xXXXX 0004 3 RW
0x407 MAX_TX_SIZE_CONFIG Specifies the maximum TX frame length. Frames that are longer are considered oversized. They are transmitted, but also increment the CNTR_TX_OVERSIZE register.

Bits [31:16] of this register are Reserved.

0xXXXX 2580 3

RW
0x40A TXMAC_CONTROL TX MAC Control Register. A single bit is defined:
  • Bit[1]: VLAN detection disabled. This bit is deasserted by default, implying VLAN detection is enabled.
30'hX2'b0X 3 RW
3 X means "Don't Care".
Level Two Title