MIPI D-PHY IP User Guide: Agilex™ 3 and Agilex™ 5 FPGAs

Download PDF
ID 817561
Date 6/30/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the MIPI D-PHY IP 2. Configuring and Generating the MIPI D-PHY IP 3. MIPI D-PHY Interface Design Guidelines 4. Simulating the MIPI D-PHY IP 5. Validating the MIPI D-PHY IP 6. Debugging the MIPI-PHY IP 7. MIPI D-PHY Architecture 8. Interface Signals and Register Maps 9. Verification Test Plan 10. Document Revision History for the MIPI D-PHY IP User Guide
1. About the MIPI D-PHY IP x
1.1. MIPI D-PHY IP Features 1.2. Unsupported Features 1.3. MIPI D-PHY IP Release Information 1.4. MIPI D-PHY IP Block Diagram 1.5. Supported Data Lanes and Clock Lane Per Single HSIO Bank 1.6. MIPI D-PHY IP Design Flow
2. Configuring and Generating the MIPI D-PHY IP x
2.1. Creating a MIPI D-PHY Project 2.2. Generating a MIPI D-PHY IP 2.3. Generating the Design Example 2.4. MIPI D-PHY IP Parameters 2.5. Compiling the Design Example
2.3. Generating the Design Example x
2.3.1. Generating the Synthesizable MIPI D-PHY Design Example
2.3.1. Generating the Synthesizable MIPI D-PHY Design Example x
2.3.1.1. Design Example Block Diagram 2.3.1.2. External Interfaces
2.4. MIPI D-PHY IP Parameters x
2.4.1. MIPI D-PHY IP Configuration Parameters 2.4.2. MIPI D-PHY Link n Tab: RX Parameters 2.4.3. MIPI D-PHY Link n Tab: TX Parameters
3. MIPI D-PHY Interface Design Guidelines x
3.1. Identifying Pin Assignments Based on Byte Location 3.2. Assigning the RZQ pin and Dedicated Reference Clock Pin for MIPI D-PHY IP 3.3. Rules for the Remaining I/O Pin from Same Byte Location 3.4. I/O Bank Sharing 3.5. MIPI D-PHY Placement Rules 3.6. Handling MIPI D-PHY IP Reset
3.4. I/O Bank Sharing x
3.4.1. MIPI I/O Bank Sharing with External Memory Interface Protocol
4. Simulating the MIPI D-PHY IP x
4.1. Simulating the MIPI D-PHY IP Design Example with External Loopback Enabled
4.1. Simulating the MIPI D-PHY IP Design Example with External Loopback Enabled x
4.1.1. Simulation Design Example with External Loopback Enabled Block Diagram 4.1.2. Simulating MIPI D-PHY IP Design Example with Modelsim* and Questasim* 4.1.3. Simulating MIPI D-PHY IP Design Example with Synopsys VCSMX* and Xcelium*
5. Validating the MIPI D-PHY IP x
5.1. Adding Signal Tap Logic Analyzer to MIPI D-PHY IP Design Example 5.2. Testing the MIPI D-PHY Design Example
6. Debugging the MIPI-PHY IP x
6.1. Creating a Simplified Design that Demonstrates the Same Problem 6.2. Evaluating FPGA Timing Problems 6.3. Determining if the Problem Exists in Previous Quartus Prime Versions 6.4. Determining if the Problem Exists in the Current Version of Software 6.5. Verifying the MIPI D-PHY IP Using the Signal Tap Logic Analyzer 6.6. Varying the Voltage 6.7. Operating at Lower Speed 6.8. Trying a Different PCB
7. MIPI D-PHY Architecture x
7.1. MIPI D-PHY IP TX 7.2. MIPI D-PHY IP RX 7.3. Initialization and Reset Sequences 7.4. Calibration 7.5. CSR Clock Domain Crossing (CDC)
8. Interface Signals and Register Maps x
8.1. Interface Signals 8.2. Register Maps
8.1. Interface Signals x
8.1.1. General Interface Signals 8.1.2. AXI-Lite Interface 8.1.3. Core Register Bus 8.1.4. D-PHY RX PPI Interface Signals 8.1.5. D-PHY TX PPI Interface Signals 8.1.6. AXI-Lite CSR Access
8.2. Register Maps x
8.2.1. D-PHY IP Registers 8.2.2. D-PHY Traffic Generator (TG) Registers
8.2.1. D-PHY IP Registers x
8.2.1.1. IP_ID 8.2.1.2. IP_CAP 8.2.1.3. D0_CAP 8.2.1.4. DN_CAP 8.2.1.5. RX_CAP 8.2.1.6. TX_CAP 8.2.1.7. TX_PREAMBLE_LEN 8.2.1.8. D-PHY_CSR 8.2.1.9. TX_CLK_LANE_PS 8.2.1.10. RX_DLANE_ERR 8.2.1.11. SKEW_CAL_LEN_B0 8.2.1.12. SKEW_CAL_LEN_B1 8.2.1.13. SKEW_CAL_LEN_B2 8.2.1.14. SKEW_CAL_LEN_B3 8.2.1.15. ALT_CAL_LEN_B0 8.2.1.16. ALT_CAL_LEN_B1 8.2.1.17. ALT_CAL_LEN_B2 8.2.1.18. ALT_CAL_LEN_B3 8.2.1.19. CLK_CSR 8.2.1.20. CLK_STATUS 8.2.1.21. DLANE_CSR_0 8.2.1.22. DLANE_STATUS_0 8.2.1.23. RX_DLANE_DESKEW_DELAY_0 8.2.1.24. RX_DLANE_ERR_0 8.2.1.25. DLANE_CSR_1 8.2.1.26. DLANE_STATUS_1 8.2.1.27. RX_DLANE_DESKEW_DELAY_1 8.2.1.28. RX_DLANE_ERR_1 8.2.1.29. DLANE_CSR_2 8.2.1.30. DLANE_STATUS_2 8.2.1.31. RX_DLANE_DESKEW_DELAY_2 8.2.1.32. RX_DLANE_ERR_2 8.2.1.33. DLANE_CSR_3 8.2.1.34. DLANE_STATUS_3 8.2.1.35. RX_DLANE_DESKEW_DELAY_3 8.2.1.36. RX_DLANE_ERR_3 8.2.1.37. DLANE_CSR_4 8.2.1.38. DLANE_STATUS_4 8.2.1.39. RX_DLANE_DESKEW_DELAY_4 8.2.1.40. RX_DLANE_ERR_4 8.2.1.41. DLANE_CSR_5 8.2.1.42. DLANE_STATUS_5 8.2.1.43. RX_DLANE_DESKEW_DELAY_5 8.2.1.44. RX_DLANE_ERR_5 8.2.1.45. DLANE_CSR_6 8.2.1.46. DLANE_STATUS_6 8.2.1.47. RX_DLANE_DESKEW_DELAY_6 8.2.1.48. RX_DLANE_ERR_6 8.2.1.49. DLANE_CSR_7 8.2.1.50. DLANE_STATUS_7 8.2.1.51. RX_DLANE_DESKEW_DELAY_7 8.2.1.52. RX_DLANE_ERR_7 8.2.1.53. TX_LPX 8.2.1.54. TX_HS_EXIT 8.2.1.55. TX_LP_EXIT 8.2.1.56. TX_CLK_PREPARE 8.2.1.57. TX_CLK_ZERO 8.2.1.58. TX_CLK_POST 8.2.1.59. TX_CLK_PRE 8.2.1.60. TX_HS_PREPARE 8.2.1.61. TX_HS_ZERO 8.2.1.62. TX_HS_TRAIL 8.2.1.63. TX_INIT 8.2.1.64. TX_WAKE 8.2.1.65. RX_CLK_LOSS_DETECT 8.2.1.66. RX_CLK_SETTLE 8.2.1.67. RX_HS_SETTLE 8.2.1.68. RX_INIT 8.2.1.69. RX_CLK_POST 8.2.1.70. RX_CAL_REG_CTRL 8.2.1.71. RX_CAL_STATUS_D-PHY 8.2.1.72. RX_CAL_SKEW_W_START_MUX 8.2.1.73. RX_CAL_SKEW_W_END_MUX 8.2.1.74. RX_CAL_ALT_W_START_MUX 8.2.1.75. RX__CAL_ALT_W_END_MUX 8.2.1.76. RX_DESKEW_DELAY_MUX 8.2.1.77. RX_CAL_STATUS_LANE_MUX 8.2.1.78. PRBS_INIT_0 8.2.1.79. PRBS_INIT_1 8.2.1.80. PRBS_INIT_2 8.2.1.81. PRBS_INIT_3 8.2.1.82. PRBS_INIT_4 8.2.1.83. PRBS_INIT_5 8.2.1.84. PRBS_INIT_6 8.2.1.85. TX_TM_CONTROL 8.2.1.86. TX_MNL_IO_0 8.2.1.87. TX_MNL_D_LP_EN 8.2.1.88. RX_TM_CONTROL
8.2.2. D-PHY Traffic Generator (TG) Registers x
8.2.2.1. TG_TOP_CTRL_0 8.2.2.2. TG_TOP_CTRL_1 8.2.2.3. TG_TOP_DONE 8.2.2.4. TG_TOP_FAIL 8.2.2.5. TG_TOP_TEST_EN 8.2.2.6. TG_TOP_TEST_LINK 8.2.2.7. TARGET_TEST_CNT 8.2.2.8. TCHK_CONTROL 8.2.2.9. TCHK_LINK_STATUS 8.2.2.10. HS_DONE_LANES 8.2.2.11. TCHK_LINK_ERR_STATUS 8.2.2.12. LANE_ERROR_SOT_LANES 8.2.2.13. CAL_ERROR_LANES 8.2.2.14. HS_ERR_LANES 8.2.2.15. HS_TEST_CNT 8.2.2.16. LPDT_TEST_CNT 8.2.2.17. TRIGGER_TEST_CNT 8.2.2.18. ULPS_TEST_CNT 8.2.2.19. TG_RX_OVRD_DATA_PAT 8.2.2.20. TG_RX_BIT_ERROR_CNT 8.2.2.21. TG_RX_HS_TXFER_CNT 8.2.2.22. TG_LINK_CONTROL 8.2.2.23. TG_INIT_CNT 8.2.2.24. TG_HS_LEN 8.2.2.25. TG_LP_LEN 8.2.2.26. TG_SKEW_CAL 8.2.2.27. TG_ALT_CAL 8.2.2.28. TG_PER_SKEW_CAL_LEN 8.2.2.29. TG_TEST_CNT 8.2.2.30. TG_OVRD_DATA_PAT 8.2.2.31. TG_TX_HS_TXFER_CNT
9. Verification Test Plan x
9.1. MIPI D-PHY Tests
1. About the MIPI D-PHY IP
2. Configuring and Generating the MIPI D-PHY IP
3. MIPI D-PHY Interface Design Guidelines
4. Simulating the MIPI D-PHY IP
5. Validating the MIPI D-PHY IP
6. Debugging the MIPI-PHY IP
7. MIPI D-PHY Architecture
8. Interface Signals and Register Maps
9. Verification Test Plan
10. Document Revision History for the MIPI D-PHY IP User Guide

3.1. Identifying Pin Assignments Based on Byte Location

In the MIPI D-PHY GUI, you must provide the pin placement location via the byte location. Look for the Byte Location parameter under the Link n Location for each Link n tab. Refer to the pin index table below for each MIPI configuration on the I/O bank. You can refer to the device pin-out files to identify the pin location with reference to the pin index. You can assign the pin location with the pin location identified.

Example for MIPI D-PHY design using 2 data lanes and 1 clock lane assigned to byte location 7: The pin index 84 and 85 are for data lane 0 (D0), pin index 86 and 87 are for data lane 1 (D1), and pin index 88 and 89 are for the clock lane (CLK).

Example for MIPI D-PHY design using 2 data lanes and 1 clock lane assigned to byte location 6: The pin index 72 and 73 are for data lane 0 (D0), pin index 74 and 75 are for data lane 1 (D1), and pin index 76 and 77 are for the clock lane (CLK).

Table 14.  MIPI Pin Assignments Based on Byte Location
Pin Index * Byte Location Number of MIPI Lanes
x1 x2 x4 x8
95 7        
94
93     D3 D7
92
91***     D2 D6
90
89 CLK CLK CLK  
88
87   D1 D1 D5
86
85 D0 D0 D0 D4
84
83 6        
82
81     D3 D3
80
79***     D2 D2
78
77 CLK CLK CLK CLK
76
75   D1 D1 D1
74
73 D0 D0 D0 D0
72
71 5        
70
69     D3 D7
68
67***     D2 D6
66
65 CLK CLK CLK  
64
63   D1 D1 D5
62**
61 D0 D0 D0 D4
60
59 4        
58
57     D3 D3
56
55***     D2 D2
54
53 CLK CLK CLK CLK
52
51   D1 D1 D1
50
49 D0 D0 D0 D0
48
47 3        
46
45     D3 D7
44
43***     D2 D6
42
41 CLK CLK CLK  
40
39   D1 D1 D5
38**
37 D0 D0 D0 D4
36
35 2        
34
33     D3 D3
32
31***     D2 D2
30
29 CLK CLK CLK CLK
28
27   D1 D1 D1
26
25 D0 D0 D0 D0
24
23 1        
22
21     D3 D7
20
19***     D2 D6
18
17 CLK CLK CLK  
16
15   D1 D1 D5
14
13 D0 D0 D0 D4
12
11 0        
10
9     D3 D3
8
7***     D2 D2
6
5 CLK CLK CLK CLK
4
3   D1 D1 D1
2
1 D0 D0 D0 D0
0
Note:

* Based on the pin index, the even number is P pin and odd number is N pin for data lane or clock lane.

** These pins can be use as RZQ pin. Refer to Assigning RZQ Pin and Dedicated Reference Clock Pin for MIPI D-PHY IP for more details.

*** Unused Pin 7 on the same I/O byte location for design with 1 or 2 data lanes plus 1 clock, should be left unused. Refer to Using the Remaining I/O Pin from Same Byte Location for details.
Level Two Title